2000 YAMAHA CYGNUS 125 oil level

1
2
3
4
5
6
7
8
9
EAU10210
TABLE OF CONTENTSSAFETY INFORMATION....... 1-1
Further safe-riding points ..... 1-4
DESCRIPTION ....................... 2-1
Left view ............................... 2-1
Right view ............................. 2-2
Controls and instruments ..... 2-3
INSTRUMENT AND CONTROL
FUNCTIONS........................... 3-1
Main switch/steering lock ..... 3-1
Indicator lights ...................... 3-2
Speedometer unit................. 3-3
Fuel gauge ............................ 3-3
Handlebar switches .............. 3-3
Front brake lever .................. 3-4
Rear brake lever ................... 3-4
Fuel tank cap ........................ 3-5
Fuel...................................... 3-6
Catalytic converter ............... 3-6
Kickstarter............................ 3-7
Seat ......................................3-7
Helmet holder ....................... 3-8
Storage compartment ........... 3-8
Luggage hook ....................... 3-9
Sidestand ...........................3-10Sidestand switch operation
check...............................3-10
PRE-OPERATION CHECKS . 4-1
Pre-operation check list ........ 4-2
OPERATION AND IMPORTANT
RIDING POINTS.................... 5-1
Starting a cold engine ........... 5-1
Starting off ............................ 5-2
Acceleration and
deceleration....................... 5-2
Braking ................................. 5-2
Tips for reducing fuel consump-
tion..................................... 5-3
Engine break-in .................... 5-3
Parking ................................. 5-4
PERIODIC MAINTENANCE
AND MINOR REPAIR ............ 6-1
Owner’s tool kit ..................... 6-1
Periodic maintenance and
lubrication chart ................. 6-3
Removing and installing
panels ................................ 6-6
Checking the spark plug ....... 6-7Engine oil and oil strainer ...... 6-8
Final transmission oil..........6-10
Air filter and V-belt case air filter
elements..........................6-11
Adjusting the carburetor..... 6-13
Adjusting the throttle cable free
play ..................................6-14
Adjusting the valve
clearance.........................6-14
Tires...................................6-15
Cast wheels.......................6-17
Checking the front brake lever
free play...........................6-17
Adjusting the rear brake lever
free play...........................6-18
Checking the front brake pads
and rear brake shoes ......6-18
Checking the brake fluid
level .................................6-19
Changing the brake fluid .....6-20
Checking and lubricating the
cables..............................6-20
Checking and lubricating the
throttle grip and cable ......6-21
Lubricating the front and rear
brake levers.....................6-21
5ML-F8199-E0ch0.pmd2003/12/12, 16:02 5

4-2
1
2
3
4
5
6
7
8
9
PRE-OPERATION CHECKS
EAU15602
Pre-operation check list
ITEM CHECKS PAGE
Fuel Check fuel level in fuel tank.
 Refuel if necessary.
 Check fuel line for leakage.3-6
Engine oil Check oil level in engine.
 If necessary, add recommended oil to specified level.
 Check vehicle for oil leakage.6-8
Final transmission oil Check vehicle for oil leakage. 6-10
Front brake Check operation.
 If soft or spongy, have Yamaha dealer bleed hydraulic system.
 Check brake pads for wear.
 Replace if necessary.
 Check fluid level in reservoir.
 If necessary, add recommended brake fluid to specified level.
 Check hydraulic system for leakage.6-18, 6-19
Rear brake Check operation.
 Lubricate cable if necessary.
 Check lever free play.
 Adjust if necessary.6-18, 6-19
Throttle grip Make sure that operation is smooth.
 Check cable free play.
 If necessary, have Yamaha dealer adjust cable free play and lubricate cable and
grip housing.6-14, 6-21
Wheels and tires Check for damage.
 Check tire condition and tread depth.
 Check air pressure.
 Correct if necessary.6-15, 6-17
Brake levers Make sure that operation is smooth.
 Lubricate lever pivoting points if necessary.6-21
5ML-F8199-E0ch4.pmd2003/12/12, 16:03 2

6-4
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR9
*Wheels Check runout and for damage.————
10*Tires Check tread depth and for damage.
 Replace if necessary.
 Check air pressure.
 Correct if necessary.———— —
11*Wheel bearings Check bearing for looseness or damage.————
12*Steering bearings Check bearing play and steering for roughness.—————
 Lubricate with lithium-soap-based grease. Every 24000 km
13*Chassis fasteners Make sure that all nuts, bolts and screws are properly tightened.———— —
14 Sidestand, centerstand Check operation.
 Lubricate.———— —
15*Sidestand switch Check operation.————— —
16*Front fork Check operation and for oil leakage.————
17*Shock absorber
assembly Check operation and shock absorber for oil leakage.————
18*Carburetor Adjust engine idling speed.————— —
19*Engine oil Change. (see page 3-2)—Every 3000 km
 Check oil level and vehicle for oil leakage. Every 3000 km—
20*Engine oil strainer Clean.—
21 Final transmission oil Check vehicle for oil leakage.—— —
 Change.———
22*V-belt Replace. Every 18000 km
23*Front and rear brake
switches Check operation.————— — NO. ITEM CHECK OR MAINTENANCE JOBODOMETER READING (u1,000 km)
ANNUAL
CHECK
1 6 12 18 24
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 4

6-8
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIRZAUM00**
1
1. Spark plug gap
Spark plug gap:
0.6~0.7 mm (0.024~0.028 in)
2. Clean the surface of the spark plug
gasket and its mating surface, and
then wipe off any grime from the
spark plug threads.
3. Install the spark plug with the spark
plug wrench, and then tighten it to
the specified torque.
Tightening torque:
Spark plug:
13 Nm (1.3m  kgf, 9.4ft  lbf)
NOTE:
If a torque wrench is not available when
installing a spark plug, a good estimate
of the correct torque is 1/4~1/2 turn past
finger tight. However, the spark plug
should be tightened to the specified
torque as soon as possible.4. Install the spark plug cap.
5. Install the panel.
EAUT1350
Engine oil and oil strainerThe engine oil level should be checked
before each ride. In addition, the oil must
be changed and the oil strainer cleaned
at the intervals specified in the periodic
maintenance and lubrication chart. The
engine oil must also be changed at the
initial 1000 km (600 mi) and when the
oil change indicator changes from green
to red. The oil change indicator must be
reset after the initial 1000 km (600 mi).
(See page 3-2 for reset procedures.)
To check the engine oil level
1.Place the vehicle on the centerstand.NOTE:
Make sure that the vehicle is positioned
straight up when checking the oil level.
A slight tilt to the side can result in a
false reading.2. Start the engine, warm it up for sev-
eral minutes, and then turn it off.
3. Wait a few minutes until the oil
settles, remove the oil filler cap,
wipe the dipstick clean, inser t it
back into the oil filler hole (without
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 8

6-9
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
screwing it in), and then remove it
again to check the oil level.
NOTE:
The engine oil should be between the
minimum and maximum level marks.ZAUM00**
1
2
1. Maximum level mark
1. Minimum level mark4. If the engine oil is below the mini-
mum level mark, add sufficient oil
of the recommended type to raise
it to the correct level.
5. Insert the dipstick into the oil filler
hole, and then tighten the oil filler
cap.To change the engine oil and clean
the oil strainer
1. Start the engine, warm it up for sev-
eral minutes, and then turn it off.
2. Place an oil pan under the engine
to collect the used oil.
3. Remove the engine oil filler cap and
drain bolts to drain the oil from the
crankcase.
ECA10410
cCWhen removing the engine oil drain
bolt, the O-ring, spring, and oil
strainer will fall out. Take care not to
lose these parts.ZAUM00**
1
1. Oil filler cap
ZAUM00**
1
1. Engine oil drain bolt AZAUM00**
1
1. Engine oil drain bolt B4. Clean the oil strainer with solvent,
and then check it for damage and
replace it if necessary.
5. Check the O-ring for damage and
replace it if necessary.
6. Install the oil strainer, spring, O-ring
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 9

6-10
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
and engine oil drain bolts, and then
tighten the drain bolts to the speci-
fied torque.
Tightening torque:
Engine oil drain bolt A:
20 Nm (2.0 m  kgf, 14.5ft  lbf)
Engine oil drain bolt B:
20 Nm (2.0 m  kgf, 14.5 ft  lbf)
NOTE:
Make sure that the O-ring is properly
seated.7. Add the specified amount of the
recommended engine oil, and then
install and tighten the engine oil filler
cap.
Recommended engine oil:
See page 8-1.
Oil change quantity:
0.9 L (0.98 US qt) (0.83 Imp.qt)
ECA11670
cC8 88 8
8Do not use oils with a diesel
specification of “CD” or oils of a
higher quality than specified. Inaddition, do not use oils labeled
“ENERGY CONSERVING II” or
higher.
8 88 8
8Be sure no foreign material en-
ters the crankcase.
8. Start the engine, and then let it idle
for several minutes while checking
it for oil leakage. If oil is leaking,
immediately turn the engine off and
check for the cause.
9. Turn the engine off, and then check
the oil level and correct it if neces-
sary.
10. Reset the oil change indicator. (See
page 3-2 for reset procedures.)NOTE:
If the engine oil is changed before the
oil change indicator changes to red (i.e.
before the periodic oil change interval
has been reached), the indicator must
be reset after the oil change for the next
periodic oil change to be indicated at the
correct time.
EAU20060
Final transmission oilThe final transmission case must be
checked for oil leakage before each ride.
If any leakage is found, have a Yamaha
dealer check and repair the scooter. In
addition, the final transmission oil must
be changed as follows at the intervals
specified in the periodic maintenance
and lubrication chart.
1. Start the engine, warm it up by
riding the scooter for several min-
utes, and then stop the engine.
2. Place the scooter on the
centerstand.
3. Place an oil pan under the final
transmission case to collect the
used oil.
4. Remove the oil filler cap and drain
bolt to drain the oil from the final
transmission case.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 10

6-19
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22540
Rear brake shoes
1
2
ZAUM00591. Wear indicator
2. Wear limit lineThe rear brake is provided with a wear
indicator, which allows you to check the
brake shoe wear without having to dis-
assemble the brake. To check the brake
shoe wear, check the position of the
wear indicator while applying the brake.
If a brake shoe has worn to the point
that the wear indicator reaches the wear
limit line, have a Yamaha dealer replace
the brake shoes as a set. groove has almost disappeared, have a
Yamaha dealer replace the brake pads
as a set.
EAU32341
Checking the brake fluid levelZAUM00**
1
1. MInimum level markInsufficient brake fluid may allow air to
enter the brake system, possibly caus-
ing it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads and/
or brake system leakage. If the brake
fluid level is low, be sure to check the
brake pads for wear and the brake sys-
tem for leakage.
Observe these precautions:8When checking the fluid level, make
sure that the top of the master cyl-
inder is level by turning the handle-
bars.
8Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.
Recommended brake fluid:
DOT 4
8Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and lead
to poor braking performance.
8Be careful that water does not en-
ter the master cylinder when refill-
ing. Water will significantly lower the
boiling point of the fluid and may
result in vapor lock.
8Brake fluid may deteriorate painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 19

6-20
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR8As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer check
the cause.
EAU22720
Changing the brake fluidHave a Yamaha dealer change the brake
fluid at the intervals specified in the
NOTE after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cylin-
der and caliper as well as the brake hose
replaced at the intervals listed below or
whenever they are damaged or leaking.
8Oil seals: Replace every two years.
8Brake hose: Replace every four
years.
EAU23100
Checking and lubricating the
cablesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be lubri-
cated if necessary. If a cable is dam-
aged or does not move smoothly, have
a Yamaha dealer check or replace it.
Recommended lubricant:
Engine oil
EWA10720
wDamage to the outer sheath may in-
terfere with proper cable operation
and will cause the inner cable to rust.
Replace a damaged cable as soon as
possible to prevent unsafe condi-
tions.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 20