2000 YAMAHA CYGNUS 125 brake

6-19
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU22540
Rear brake shoes
1
2
ZAUM00591. Wear indicator
2. Wear limit lineThe rear brake is provided with a wear
indicator, which allows you to check the
brake shoe wear without having to dis-
assemble the brake. To check the brake
shoe wear, check the position of the
wear indicator while applying the brake.
If a brake shoe has worn to the point
that the wear indicator reaches the wear
limit line, have a Yamaha dealer replace
the brake shoes as a set. groove has almost disappeared, have a
Yamaha dealer replace the brake pads
as a set.
EAU32341
Checking the brake fluid levelZAUM00**
1
1. MInimum level markInsufficient brake fluid may allow air to
enter the brake system, possibly caus-
ing it to become ineffective.
Before riding, check that the brake fluid
is above the minimum level mark and
replenish if necessary. A low brake fluid
level may indicate worn brake pads and/
or brake system leakage. If the brake
fluid level is low, be sure to check the
brake pads for wear and the brake sys-
tem for leakage.
Observe these precautions:8When checking the fluid level, make
sure that the top of the master cyl-
inder is level by turning the handle-
bars.
8Use only the recommended quality
brake fluid, otherwise the rubber
seals may deteriorate, causing
leakage and poor braking perfor-
mance.
Recommended brake fluid:
DOT 4
8Refill with the same type of brake
fluid. Mixing fluids may result in a
harmful chemical reaction and lead
to poor braking performance.
8Be careful that water does not en-
ter the master cylinder when refill-
ing. Water will significantly lower the
boiling point of the fluid and may
result in vapor lock.
8Brake fluid may deteriorate painted
surfaces or plastic parts. Always
clean up spilled fluid immediately.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 19

6-20
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR8As the brake pads wear, it is nor-
mal for the brake fluid level to
gradually go down. However, if the
brake fluid level goes down sud-
denly, have a Yamaha dealer check
the cause.
EAU22720
Changing the brake fluidHave a Yamaha dealer change the brake
fluid at the intervals specified in the
NOTE after the periodic maintenance
and lubrication chart. In addition, have
the oil seals of the brake master cylin-
der and caliper as well as the brake hose
replaced at the intervals listed below or
whenever they are damaged or leaking.
8Oil seals: Replace every two years.
8Brake hose: Replace every four
years.
EAU23100
Checking and lubricating the
cablesThe operation of all control cables and
the condition of the cables should be
checked before each ride, and the
cables and cable ends should be lubri-
cated if necessary. If a cable is dam-
aged or does not move smoothly, have
a Yamaha dealer check or replace it.
Recommended lubricant:
Engine oil
EWA10720
wDamage to the outer sheath may in-
terfere with proper cable operation
and will cause the inner cable to rust.
Replace a damaged cable as soon as
possible to prevent unsafe condi-
tions.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 20

6-21
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23110
Checking and lubricating the
throttle grip and cableThe operation of the throttle grip should
be checked before each ride. In addi-
tion, the cable should be lubricated or
replaced at the intervals specified in the
periodic maintenance chart.
EAU23170
Lubricating the front and rear
brake leversZAUM00**The pivoting points of the front and rear
brake levers must be lubricated at the
intervals specified in the periodic main-
tenance and lubrication chart.
Recommended lubricant:
Lithium-soap-based grease (all-pur-
pose grease)
EAU23210
Checking and lubricating the
centerstand and sidestandZAUM00**The operation of the centerstand and
sidestand should be checked before
each ride, and the pivots and metal-to-
metal contact surfaces should be lubri-
cated if necessary.
EWA10740
wIf the centerstand or sidestand does
not move up and down smoothly,
have a Yamaha dealer check or repair
it.
Recommended lubricant:
Lithium-soap-based grease (all-pur-
pose grease)
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 21

6-22
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
EAU23271
Checking the front forkThe condition and operation of the front
fork must be checked as follows at the
intervals specified in the periodic main-
tenance and lubrication chart.
To check the condition
EWA10750
wSecurely support the motorcycle so
that there is no danger of it falling
over.Check the inner tubes for scratches,
damage and excessive oil leakage.
To check the operation
1. Place the motorcycle on a level sur-
face and hold it in an upright posi-
tion.
2. While applying the front brake, push
down hard on the handlebars sev-
eral times to check if the front fork
compresses and rebounds
smoothly.
ZAUM00**
ECA10590
cCIf any damage is found or the front
fork does not operate smoothly, have
a Yamaha dealer check or repair it.
EAU23280
Checking the steeringWorn or loose steering bearings may
cause danger. Therefore, the operation
of the steering must be checked as fol-
lows at the intervals specified in the
periodic maintenance and lubrication
chart.
1. Place a stand under the engine to
raise the front wheel off the ground.
EWA10750
wSecurely support the motorcycle so
that there is no danger of it falling
over.2. Hold the lower ends of the front fork
legs and try to move them forward
and backward. If any free play can
be felt, have a Yamaha dealer check
or repair the steering.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 22

6-27
1
2
3
4
5
6
7
8
9
PERIODIC MAINTENANCE AND MINOR REPAIR
the bulb life will be adversely affected.
Thoroughly clean off any dirt and fin-
gerprints on the headlight bulb us-
ing a cloth moistened with alcohol
or thinner.6. Install the headlight bulb cover, and
then connect the coupler.
7. Install the panel.
8. Have a Yamaha dealer adjust the
headlight beam if necessary.
EAU24131
Replacing the tail/brake light
bulb1. Remove the tail/brake light lens by
removing the screws.
2. Remove the defective bulb by push-
ing it in and turning it counterclock-
wise.ZAUM00**
1
1. Bulb3. Insert a new bulb into the socket,
push it in, and then turn it clock-
wise until it stops.
4. Install the lens by installing the
screws.
ECA10680
cCDo not overtighten the screws, other-
wise the lens may break.
5ML-F8199-E0ch6re.pmd2003/12/12, 16:04 27

7-1
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGE
EAU26090
CareWhile the open design of a scooter re-
veals the attractiveness of the technol-
ogy, it also makes it more vulnerable.
Rust and corrosion can develop even if
high-quality components are used. A
rusty exhaust pipe may go unnoticed on
a car, however, it detracts from the over-
all appearance of a scooter. Frequent and
proper care does not only comply with
the terms of the warranty, but it will also
keep your scooter looking good, extend
its life and optimize its performance.
Before cleaning
1. Cover the muffler outlet with a plas-
tic bag after the engine has cooled
down.
2. Make sure that all caps and cov-
ers as well as all electrical couplers
and connectors, including the spark
plug cap, are tightly installed.
3. Remove extremely stubborn dirt,
like oil burnt onto the crankcase,
with a degreasing agent and a
brush, but never apply such prod-ucts onto seals, gaskets and wheel
axles. Always rinse the dirt and
degreaser off with water.
Cleaning
ECA10780
cC8 88 8
8Avoid using strong acidic wheel
cleaners, especially on spoked
wheels. If such products are used
on hard-to-remove dirt, do not
leave the cleaner on the affected
area any longer than instructed.
Also, thoroughly rinse the area
off with water, immediately dry
it, and then apply a corrosion
protection spray.
8 88 8
8Improper cleaning can damage
windshields, cowlings, panels
and other plastic parts. Use only
a soft, clean cloth or sponge with
mild detergent and water to clean
plastic.
8 88 8
8Do not use any harsh chemical
products on plastic parts. Be sure
to avoid using cloths or sponges
which have been in contact with
strong or abrasive cleaning prod-ucts, solvent or thinner, fuel
(gasoline), rust removers or in-
hibitors, brake fluid, antifreeze or
electrolyte.
8 88 8
8Do not use high-pressure wash-
ers or steam-jet cleaners since
they cause water seepage and
deterioration in the following ar-
eas: seals (of wheel and
swingarm bearings, fork and
brakes), electric components
(couplers, connectors, instru-
ments, switches and lights),
breather hoses and vents.
8 88 8
8For scooters equipped with a
windshield: Do not use strong
cleaners or hard sponges as they
will cause dulling or scratching.
Some cleaning compounds for
plastic may leave scratches on
the windshield. Test the product
on a small hidden part of the
windshield to make sure that it
does not leave any marks. If the
windshield is scratched, use a
quality plastic polishing com-
pound after washing.
EAU25990
SCOOTER CARE AND STORAGE
5ML-F8199-E0ch7re.pmd2003/12/12, 16:04 1

7-2
1
2
3
4
5
6
7
8
9
SCOOTER CARE AND STORAGEAfter normal use
Remove dirt with warm water, a mild
detergent, and a soft, clean sponge, and
then rinse thoroughly with clean water.
Use a toothbrush or bottlebrush for hard-
to-reach areas. Stubborn dirt and insects
will come off more easily if the area is
covered with a wet cloth for a few min-
utes before cleaning.After riding in the rain, near the sea oron salt-sprayed roads
Since sea salt or salt sprayed on the
roads during winter are extremely corro-
sive in combination with water, carry out
the following steps after each ride in the
rain, near the sea or on salt-sprayed
roads.NOTE:
Salt sprayed on roads in the winter may
remain well into spring.1. Clean the scooter with cold water
and a mild detergent after the en-
gine has cooled down.
ECA10790
cCDo not use warm water since it in-
creases the corrosive action of the
salt.2. Apply a corrosion protection spray
on all metal, including chrome- and
nickel-plated, surfaces to prevent
corrosion.
After cleaning
1. Dry the scooter with a chamois or
an absorbing cloth.
2. Use a chrome polish to shine
chrome, aluminum and stainless-
steel parts, including the exhaust
system. (Even the thermally in-
duced discoloring of stainless-steel
exhaust systems can be removed
through polishing.)
3. To prevent corrosion, it is recom-
mended to apply a corrosion pro-
tection spray on all metal, includ-
ing chrome- and nickel-plated, sur-
faces.
4. Use spray oil as a universal cleaner
to remove any remaining dirt.5. Touch up minor paint damage
caused by stones, etc.
6. Wax all painted surfaces.
7. Let the scooter dry completely be-
fore storing or covering it.
EWA10940
w8 88 8
8Make sure that there is no oil or
wax on the brakes or tires. If nec-
essary, clean the brake discs and
brake linings with a regular brake
disc cleaner or acetone, and
wash the tires with warm water
and a mild detergent.
8 88 8
8Before operating the scooter test
its braking performance and cor-
nering behavior.
ECA10800
cC8 88 8
8Apply spray oil and wax spar-
ingly and make sure to wipe off
any excess.
8 88 8
8Never apply oil or wax to any rub-
ber and plastic parts, but treat
them with a suitable care prod-
uct.
5ML-F8199-E0ch7re.pmd2003/12/12, 16:04 2

8-2
1
2
3
4
5
6
7
8
9
SPECIFICATIONSFront tireType
Tubeless
Size
110 / 70-12 47L
Manufacturer/model
CHENG SHIN / C-922N-47LRear tireType
Tubeless
Size
120 / 70-12 58L
Manufacturer/model
CHENG SHIN / C-6007-58L
Maximum load
170 kg
(Total weight of rider, passenger, cargo and ac-
cessories)Tire air pressure (measured on cold tires)Loading condition
0-90 kg
Front
175 kPa
Rear
200 kPa
Loading condition
90-170 kg
Front
200 kPa
Rear
225 kPaFront wheelWheel type
Cast wheel
Rim size
12xMT2.75
Rear wheelWheel type
Cast wheel
Rim size
12xMT3.00Front brakeType
Single disc brake
Operation
Right hand operation
Recommended fluid
DOT 4Rear brakeType
Drum brake
Operation
Left hand operationFront suspensionType
Telescopic fork
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
90.0 mmRear suspensionType
Unit swing
Spring/shock absorber type
Coil spring/oil damper
Wheel travel
95.0 mm
Electrical systemIgnition system
C.D.I.
Charging system
A.C. magnetoBatteryModel
YTX7A-BS
Voltage, capacity
12 V, 6.0 AhHeadlightBulb type
Halogen bulbBulb voltage, wattage x quantityHeadlight
12 V, 60 W/55.0 W x 1
Tail/brake light
12 V, 5.0/21.0 W x 1
Front turn signal light
12 V, 10.0 W x 2
Rear turn signal light
12 V, 16.0 W x 2
Auxiliary light
12 V, 5.0 W x 1
Meter lighting
12 V, 1.7 W x 3
High beam indicator light
12 V, 1.7 W x 1
Turn signal indicator light
12 V, 3.4 W x 1
5ML-F8199-E0ch8re.pmd2003/12/12, 16:04 2