2000 SUZUKI SWIFT brake

9-32 BODY SERVICE
Hole to hole distance
[B] : 5 door model f. Side sill scuff installation rear hole l. Rear door rear notch
a. Front door upper hinge installation hole g. Front shoulder adjuster installation upper
holem. Rear door switch installation hole
b. Front door lower hinge installation hole h. Rear door upper hinge installation hole n. Side soil scuff installation rear hole
c. Front pillar inner trim installation lower hole i. Front door switch installation hole o. Parking brake cable bracket installation rear
hole
d. Front pillar inner trim installation upper hole j. Rear door lower hinge installation hole p. Steering support member installation hole
e. Assistant grip installation front hole k. Assistant grip installation hole
a-g : 1166 mm (45.90 in.) d-i : 820 mm (32.28 in.) i-o : 742 mm (29.21 in.)
a-h : 942 mm (37.09 in.) d-o : 1252 mm (49.29 in.) j-m : 895 mm (35.24 in.)
a-i : 901 mm (35.47 in.) e- f : 1077 mm (42.40 in.) k-n : 1089 mm (42.87 in.)
b-i : 891 mm (35.08 in.) e-o : 1244 mm (48.98 in.) k-o : 1321 mm (52.01 in.)
b-j : 902 mm (35.51 in.) f-g: 1048 mm (41.26 in.) l-n : 948 mm (37.32 in.)
b-o : 1222 mm (48.11 in.) f-o 785 mm (30.91 in.) l-o : 1323 mm (52.09 in.)
c-f : 884 mm (34.80 in.) g-l : 621 mm (24.45 in.) m-o : 1111 mm (43.74 in.)
c-o: 1282 mm (50.47 in.) g-o : 1147 mm (45.16 in.) n-o : 813 mm (32.00 in.)
d-f : 993 mm (39.09 in.) h-l : 846 mm (33.31 in.) o-p : 1229 mm (48.39 in.)
d-g : 580 mm (22.83 in.) h-m : 813 mm (32.01 in.)
a
c
gd
ek
l
m
n
i
h
bf
j
a
c
dl
k
g
e
n
m
i
f
b o
o [B]

BODY SERVICE 9-33
Hole to hole distance
[A] : 3 door model f. Quarter window lower side rear mounting hole (5.1 x 8.6 mm)
[B] : 5 door model g. Quarter window lower side front mounting hole (5.1 x 8.6 mm)
a (a’). Front end of front windshield upper installation section h. Quarter window upper notch
b (b). Front end of front windshield lower installation section i. Quarter window rear notch
c. Garnish installation center hole (φ5
mm) j. Quarter window lower mounting hole (5.1 x 8.6 mm)
d. Quarter window upper side front notch k. Parking brake cable bracket installation rear hole
e. Quarter window rear notch
a-a’ : 1047 mm (41.22 in.) b-k : 1411 mm (55.55 in.) f-k : 1373 mm (54.06 in.)
a-b : 688 mm (27.01 in.) d-e : 577 mm (22.72 in.) g-k : 1092 mm (42.99 in.)
a-b’ : 1356 mm (53.39 in.) d-f : 623 mm (24.53 in.) h-i : 237 mm (9.33 in.)
a-c : 1032 mm (40.63 in.) d-g : 363 mm (14.29 in.) h-k : 1430 mm (56.30 in.)
a-k : 1282 mm (50.47 in.) d-k : 1271 mm (50.04 in.) i-j : 242 mm (9.53 in.)
b-b’ : 1305 mm (51.38 in.) e-k : 1474 mm (58.03 in.) j-k : 1413 mm (55.63 in.)
[A]
[B]e
f
gd
a
a
a’
a’
b
b
k
hi
j
k
b’
b’
c
c
k

BODY SERVICE 9-47
IGNITION SWITCH LOCK CYLINDER
REMOVAL AND INSTALLATION
Refer to “STEERING LOCK ASSEMBLY (IGNITION SWITCH)” in
Section 3C.
ELECTRICAL DIAGNOSIS
For ignition switch electrical troubleshooting, refer to “IGNITION
SWITCH” in Section 8.
EXTERIOR AND INTERIOR TRIM
FLOOR CARPET
REMOVAL
1) Remove front seats and rear seat cushion.
2) Remove seat belt lower anchor bolt.
3) Remove dash side trims, front side sill scuffs, center pillar inner lower trims, quarter inner trims and rear side
sill scuffs.
4) Remove parking brake lever cover and console box.
5) Remove floor carpet.
INSTALLATION
Reverse removal sequence to install front floor carpet, noting the following instruction.
For tightening torque of seat belt anchor bolt, refer to “FRONT SEAT BELT” in Section 10.
1. Floor carpet
2. Dash panel silencer
3. Silencer seat

AIR BAG SYSTEM 10B-17
Fig. for STEP 3
Special tool
(A) : 09932-76010
Table B :
NOTE:
Upon completion of inspection and repair work, perform following items.
Reconnect all air bag system components, ensure all components are properly mounted.
Repeat AIR BAG DIAGNOSTIC SYSTEM CHECK to confirm that the trouble has been corrected.
Step Action Yes No
1 1) Set parking brake.
2) Note combination meter when ignition
switch is turned ON.
Does the “BRAKE” indicator (warning lamp)
come ON?Go to step 2.“BLK/WHT” wire, “IG
METER” fuse or J/B
(between ignition switch
and combination meter)
open or short to ground
2 1) With ignition switch OFF, disconnect SDM.
2) Check electrical connection check mecha-
nism.
Is it in good condition?Go to step 3. Repair electrical connec-
tion check mechanism.
3 1) Disconnect SDM.
2) Check proper connection to SDM at termi-
nal “Q06-2”.
3) If OK then check voltage from “Q06-2” ter-
minal of SDM connector to body ground
with ignition switch ON.
Is it 8 V or more?Substitute a known-good
SDM and recheck.Go to step 4.
4 1) Remove combination meter. Refer to COM-
BINATION METER in SECTION 8.
2) Check proper connection to combination
meter at “YEL/BLK” terminal for “AIR BAG”
warning lamp and to SDM at terminal “Q06-
2”.
3) If OK then check resistance between “YEL/
BLK” wire terminal of combination meter
connector (16-pin connector) and “Q06-2”
terminal of SDM connector.
Is resistance 1 Ω or less?Go to step 5. Repair high resistance or
open in “YEL/BLK” wire
circuit (between combina-
tion meter and SDM).