2000 SUZUKI SWIFT fuel pump

6E2-20 ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13)
[Using SUZUKI scan tool]
a) Connect SUZUKI scan tool to DLC with ignition switch OFF.
b) Turn ignition switch ON and then select “DATA LIST” mode on
scan tool.
c) Make sure that vehicle condition is as following.

Vehicle speed = 0 KPH

Engine speed = 0 RPM

Fuel tank level
15%
d) Clear DTC by using “CLEAR INFO” mode.
e) Check fuel pressure by using “FUEL PUMP CONT” mode in
“MISC TEST” menu.
CONDITIONFUEL PRESSURE
With fuel pump operating
2.7 – 3.1 kg / cm2
270 – 310 kPa
38.4 – 44.0 psi
Within 1 min. after fuel pump
stop (Pressure reduces as
time passes)Over 2.0 kg / cm2
200 kPa
28.4 psi
If measured pressure doesn’t satisfy specification, refer to
“Diagnostic Flow Table B-3” and check each possibly defective
part. Replace if found defective.
f) Start engine and warm it up to normal operating temperature.
And then check fuel pressure.
CONDITIONFUEL PRESSURE
At specified idle speed
2.0 – 2.4 kg / cm2
200 – 240 kPa
28.4 – 34.1 psi
If measured pressure doesn’t satisfy specification, refer to
“Diagnostic Flow Table B-3” and check each possibly defective
part. Replace if found defective.
g) After checking fuel pressure, remove fuel pressure gauge.
CAUTION:
As fuel feed line is still under high fuel pressure, make
sure to release fuel pressure according to following pro-
cedures.

Place fuel container under joint.

Cover joint with rag and loosen joint nut slowly to re-
lease fuel pressure gradually.
h) Remove special tools from fuel delivery pipe.
i) Connect fuel feed hose to fuel delivery pipe and clamp it secure-
ly.
j) With engine OFF and ignition switch ON, check for fuel leaks.
Tightening Torque
Fuel pressure regulator bolt: 11 N
.m (1.1 kg-m, 8.0 lb-ft)

1. Fuel filler
2. Ignition switch
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-21
FUEL PUMP
On-Vehicle Inspection
CAUTION:
When fuel filler cap is removed in any procedure, work must
be done in a well-ventilated area, keep away from any open
flames and without smoking.
NOTE:
The fuel pressure regulator is the one body with the fuel pump
assembly so individual inspection of it is impossible.
1) Remove filler cap and turn ON ignition switch. Then fuel pump
operating sound should be heard from fuel filler for about 2 se-
conds and stop. Be sure to reinstall fuel filler cap after checking.
If above check result is not satisfactory, advance to “Diagnostic
Flow Table B-2”.
2) Turn OFF ignition switch and leave over 10 minutes as it is.
3) Fuel pressure should be felt at fuel return hose (1) for 2 seconds
after ignition switch ON.
If fuel pressure is not felt, advance to “Diagnostic Flow Table
B-3”.
Removal
Remove fuel tank from body according to procedure described in
Section 6C and remove fuel pump from fuel tank.
Inspection
Check fuel pump filter for evidence of dirt and contamination. If
present, clean and check for presence of dirt in fuel tank.
Installation
1) Install fuel pump to its bracket.
2) Install fuel pump to fuel tank and then install fuel tank to body ac-
cording to procedure described in Section 6C.

When not using
SUZUKI scan tool : When using
SUZUKI scan tool :
4. Keep as far apart
as possible
ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-25
4) Install suitable vinyl tube onto injector nozzle to prevent fuel from
splashing out when injecting.
5) Put graduated cylinder under injector as shown.
6) Operate fuel pump and apply fuel pressure to injector as follows:
When using SUZUKI scan tool :
a) Connect SUZUKI scan tool to DLC with ignition switch OFF.
b) Turn ignition switch ON, clear DTC and select “MISC TEST”
mode on SUZUKI scan tool.
c) Turn fuel pump ON by using SUZUKI scan tool.
Special Tool
(A): 09931-76011 (SUZUKI scan tool)
(B): Mass storage cartridge
(C): 09931-76030 (16 / 14 pin DLC cable)
When not using SUZUKI scan tool :
a) Remove fuel pump relay from connector.
b) Connect two terminals of relay connector using service wire
(1) as shown in figure.
CAUTION:
Check to make sure that connection is made between
correct terminals. Wrong connection can cause dam-
age to ECM, wire harness, etc.
c) Turn ignition switch ON.
7) Apply battery voltage (3) to injector (2) for 15 seconds and mea-
sure injected fuel volume with graduated cylinder.
Test each injector two or three times.
If not within specification, replace injector.
Injected fuel volume:
38 – 48 cc / 15 sec. (1.28 / 1.34 – 1.62 / 1.69 US / Imp. oz / 15 sec.)
8) Check fuel leakage from injector nozzle. Do not operate injector
for this check (but fuel pump should be at work).
If fuel leaks (1) more than following specifications, replace.
Fuel leakage (1): Less than 1 drop / min.

ENGINE AND EMISSION CONTROL SYSTEM (SFI FOR G13) 6E2-33
VEHICLE SPEED SENSOR (VSS)
Inspection
Check vehicle speed sensor referring to step 3 of DTC P0500 Flow
Table. If malfunction is found, replace.
Removal / Installation
Refer to Section 7A.
FUEL LEVEL SENSOR (GAUGE)
Inspection
Refer to Section 8.
Removal / Installation
Refer to Section 6C.
MAIN RELAY, FUEL PUMP RELAY AND RADIATOR
FAN CONTROL RELAY
Inspection
1) Disconnect negative cable at battery.
2) Remove main relay (1), fuel pump relay (2) and radiator fan con-
trol relay (3) from relay box.
3) Check that there is no continuity between terminal “c” and “d”.
If there is continuity, replace relay.
4) Connect battery positive (+) terminal to terminal “b” of relay.
Connect battery negative (–) terminal “a” of relay.
Check continuity between terminal “c” and “d”.
If there is no continuity when relay is connected to the battery,
replace relay.