2000 SUZUKI GRAND VITARA body electrical system

YH4
GRAND
vol.1
0A
0B
1A
1B
3
3A
3B1
3C
3C1
3D
3E
3F
4A2
4B
5
6
7A5A
5B
5C
5E1
6A1
6A2
6A4
6B
6C
6E1
6E2
6F1
6F2
6G
6G1
6H
6K
7A1
7B1
7C1
7D
7E
7F
8
8B
8C
8D
8G
9
10
10A
8A
10B
6-1ENGINE
General Information and
Diagnosis (G16 / J20)
General Information and
Diagnosis (H25)
Engine Mechanical (G16)
Engine Mechanical (H25)
Engine Mechanical (J20)
Engine Cooling
Engine Fuel
Engine and Emission Control
System (SFI for G16 / J20)
Engine and Emission Control
System (SFI for H25)
Ignition System (G16)
Ignition System (J20 / H25)
Cranking System
(Reduction Type)
Cranking System
(No-Reduction Type)
Charging System
Exhaust System
TRANSMISSION, CLUTCH
AND DIFFERENTIAL
Manual Transmission (Type 1)
Manual Transmission (Type 2)
Automatic Transmission
Clutch (Hydraulic Type)
Transfer
Differential (Front)
Differential (Rear)
BODY ELECTRICAL SYSTEM
Wiring Diagram
Lighting System
Instrumentation / Driver
Information
Windows, Mirrors, Security
and Lock
Immobilizer Control System
BODY SERVICE
RESTRAINT SYSTEM
Seat Belt
Air Bag System GENERAL INFORMATION
General Information
Maintenance and Lubrication
TABLE OF CONTENTS TABLE OF CONTENTS SECTIONSECTION
0B
HEATING AND AIR
CONDITIONING
Heater and Ventilation
Air Conditioning
STEERING, SUSPENSION,
WHEELS AND TIRES
Front End Alignment
Power Steering (P / S) System
Steering Wheel and Column
(Not Equipped with Air Bag)
Air Bag Steering Wheel
and Column
Front Suspension
Rear Suspension
Wheel and Tires
1A
3A 0A
1B
3B1
3C
3C1
3D
3E
3F36A16
6A2
6A4
6B
6C
6E1
6E2
6F1
DRIVE SHAFT / PROP. SHAFT
Front Drive Shaft / Shaft
Bearing, Oil Seal
Propeller Shaft
BRAKES
Brake Pipe / Hose / Master
Cylinder
Front Brakes
Parking and Rear Brakes
Antilock Brake System
4A2
4B
5
5A
5B
5C
5E1
6F2
6G
6G1
6H
6K
7A
7A1
7B1
7C1
7D
7E
7F
8
8A
8B
8C
8D
8G
9
10
10A
10B
6-1
NOTE:
The screen toned Sections 6 ± 6K are included in Volume 2 and Section 8A is in Wiring
Diagram Manual.

YH4
GRAND
VITARA
0A
GENERAL INFORMATION 0A-1
SECTION 0A
GENERAL INFORMATION
CONTENTS
HOW TO USE THIS MANUAL0A- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTIONS0A- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Vehicle Equipped with a Supplemental Restraint (Air Bag) System 0A- 3. . . . . . . . . . . . . . . .
Diagnosis0A- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Servicing and Handling0A- 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
General Precautions0A- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Catalytic Converter 0A- 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precautions for Electrical Circuit Service 0A-10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electrical Circuit Inspection Procedure 0A-12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Intermittent and Poor Connection 0A-15. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Precaution for Installing Mobile Communication Equipment 0A-16. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IDENTIFICATION INFORMATION0A-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Body Number0A-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine Identification Number0A-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Transmission Identification Number 0A-17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WARNING, CAUTION AND INFORMATION LABELS0A-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
VEHICLE LIFTING POINTS0A-19 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ABBREVIATIONS MAY BE USED IN THIS MANUAL0A-21 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
METRIC INFORMATION0A-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Metric Fasteners0A-23 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fasteners Strength Identification 0A-23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Standard Tightening Torque0A-24 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
8
BODY ELECTRICAL SYSTEM 8-1
SECTION 8
BODY ELECTRICAL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
WIRING SYSTEM
(Harnesses, Connectors, Fuses, Relay, Switches, Grounds, System Circuit Diagram)Section 8A . . . . . . .
LIGHTING SYSTEMSection 8B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER INFORMATIONSection 8C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDOWS, MIRRORS, SECURITY AND LOCKSSection 8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMMOBILIZER CONTROL SYSTEMSection 8F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
8-2 BODY ELECTRICAL SYSTEM
GENERAL DESCRIPTION
The body electrical components of this vehicle are designed to operate on 12 Volts power supplied by the battery.
The electrical system utilizes negative ground polarity.
CAUTIONS IN SERVICING
When performing works related to electric systems, observe follow-
ing cautions for the purpose of protection of electrical parts and pre-
vention of a fire from occurrence.

When removing the battery from the vehicle or disconnecting the
cable from the battery terminals for inspection or service works
on the electric systems, always confirm first that the ignition
switch and all the other switches have been turned OFF. Other-
wise, the semi-conductor part may be damaged.

When disconnecting cables from the battery, be sure to discon-
nect the one from the negative (±) terminal first and then the other
from the positive (+) terminal.

Reverse the above order when connecting the cables to the bat-
tery terminals.

When disconnecting connectors, never pull the wiring harnesses.
Unlock the connector lock first and then pull them apart by holding
connectors themselves.

When connecting connectors, also hold connectors and put them
together until they lock securely (a click is heard).

YH4
GRAND
VITARA
BODY ELECTRICAL SYSTEM 8-3

When installing the wiring harness, fix it with clamps so that no
slack is left.

When installing vehicle parts, be careful so that the wiring har-
ness is not interfered with or caught by any other part.

To avoid damage to the harness, protect its part which may con-
tact against a part forming a sharp angle by winding tape or the
like around it.

When replacing a fuse, make sure to use a fuse of the specified
capacity. Use of a fuse with a larger capacity will cause a damage
to the electrical parts and a fire.

Always be careful not to handle electrical parts (computer, relay,
etc.) in a rough manner or drop them.

YH4
GRAND
VITARA
8-4 BODY ELECTRICAL SYSTEM

When performing a work that produces a heat exceeding 80C
in the vicinity of the electrical parts, remove the heat sensitive
electrical part(s) beforehand.

Use care not to expose connectors and electrical parts to water
which will be a cause of a trouble.

When using a tester for checking continuity or measuring voltage,
be sure to insert the tester probe from the wire harness side.
SYMBOLS AND MARKS
Refer to Section 8A.
ABBREVIATIONS
Refer to Section 8A.

YH4
GRAND
VITARA
Symbol
G : Green
G / Y : Green / Yellow G (Base Color)
G (Base Color)
Y (Stripe Color)G/Y
BODY ELECTRICAL SYSTEM 8-5
WIRE COLOR SYMBOLS
The wire color is abbreviated to the first (or first two) alphabet(s) of
each color.
There are two kinds of colored wire used in this vehicle. One is
single-colored wire and the other is dual-colored (striped) wire.
The single-colored wire uses only one color symbol (i.e. ªGº).
The dual-colored wire uses two color symbols (i.e. ªG / Yº). The first
symbol represents the base color of the wire (ªGº in the figure) and
the second symbol represents the color of the stripe (ªYº in the fig-
ure).
JOINT CONNECTOR (J / C)

Wiring of this vehicle employs joint connector (J / C) which divide
one wire into several different wires or combine several different
wires into one wire.

The joint connector is as shown in the figure.
FUSE BOX AND RELAY
Refer to Section 8A.

YH4
GRAND
VITARA
8-6 BODY ELECTRICAL SYSTEM
POWER SUPPLY DIAGRAM
Refer to Section 8A.