2000 SUZUKI GRAND VITARA key

YH4
GRAND
VITARA
8D
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-1
GENERAL DESCRIPTION8D- 2 . . . . . . . . . . . . . .
Cautions in Servicing 8D- 2. . . . . . . . . . . . . . . . .
Symbols and Marks 8D- 2. . . . . . . . . . . . . . . . . . .
Wiring Color Symbols 8D- 2. . . . . . . . . . . . . . . . .
Abbreviations 8D- 2. . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector 8D- 2. . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay 8D- 2. . . . . . . . . . . . . . . . . .
Power Supply Diagram 8D- 2. . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 2. . . . . . . . .
Front Wiper and Washer 8D- 2. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D- 3.
Power Door Lock and Keyless Entry
(If Equipped) System 8D- 4. . . . . . . . . . . . . . . .
DIAGNOSIS8D- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 5. . . . . . . . .
Front Wiper and Washer 8D- 5. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D- 5.
Rear Window Defogger (If Equipped) 8D- 5. . .
Power Window Control System 8D- 5. . . . . . . . .
Power Door Lock System (If Keyless
Entry is not Equipped) 8D- 6. . . . . . . . . . . . . . . Power Door Lock and Keyless Entry
System (If Keyless Entry is Equipped) 8D- 7. .
Power Door Mirror Control System 8D- 8. . . . . .
Door Mirror Heater (If Equipped) 8D- 8. . . . . . . .
Power Sliding Roof (If Equipped) 8D- 8. . . . . . .
Front Seat Heater (If Equipped) 8D- 8. . . . . . . .
ON-VEHICLE SERVICE8D- 9 . . . . . . . . . . . . . . . .
Windshield Wiper and Washer 8D- 9. . . . . . . . .
Front Wiper and Washer 8D- 9. . . . . . . . . . . . .
Rear Wiper and Washer (If Equipped) 8D-13.
Rear Window Defogger (If Equipped) 8D-16. . .
Power Window Control System 8D-18. . . . . . . . .
Power Door Lock System (If Keyless
Entry is not Equipped) 8D-20. . . . . . . . . . . . . . .
Power Door Lock and Keyless Entry
System (If Keyless Entry is Equipped) 8D-23. .
Power Door Mirror Control System 8D-30. . . . . .
Door Mirror Heater (If Equipped) 8D-31. . . . . . . .
Power Sliding Roof (If Equipped) 8D-32. . . . . . .
Front Seat Heater (If Equipped) 8D-33. . . . . . . .
SECTION 8D
WINDOWS, MIRRORS, SECURITY AND LOCKS
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
8D-4 WINDOWS, MIRRORS, SECURITY AND LOCKS
LH steering vehicleRH steering vehicle
Type 1
Type 2
Power Door Lock Controller (Canvas Top Model)
Power Door Lock SwitchBack Door Actuator
(except Canvas Top
Model)
Rear Door Actuator
Front Door Actuator
Fuse box
Power Door Lock and Keyless Entry (if equipped)
Controller (Hard Top Model)Keyless Entry Transmitter
(If keyless entry is equipped)
The illustration shows LH steering vehicle.
And RH steering vehicle is symmetrical.
POWER DOOR LOCK AND KEYLESS ENTRY (IF EQUIPPED) SYSTEM

YH4
GRAND
VITARA
8D-6 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR LOCK SYSTEM (IF KEYLESS ENTRY IS NOT EQUIPPED)
TroublePossible causeCorrection
All power doors are not
locked / unlocked by both
driver side door key
switch and power door
lock switch
ªDOOR LOCKº fuse blown (Hard Top
Model)
ªD / Lº fuse blown (Canvas Top Model)

Power door controller faulty

Wiring or grounding faultyReplace fuse to check for short
Replace controller
Repair
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-7
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
TroublePossible causeCorrection

All power doors are not
locked / unlocked by
both driver side door key
switch and power door
lock switch. But all
power doors are locked /
unlocked by keyless
entry transmitter

All power doors are not
locked / unlocked by
driver side door key
switch, power door lock
switch and keyless entry
transmitter

When power doors are
locked / unlocked by
keyless entry
transmitter, hazard
warning lights do not
flash
ªDOOR LOCKº fuse blown

Power door lock and keyless entry system
faultyReplace fuse to check for short
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
All power doors are not
locked / unlocked by only
power door lock switch
Power door lock switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
driver side door key
switch
Driver side door key switch faulty

Wiring or grounding faultyReplace switch
Repair
All power doors are not
locked / unlocked by only
keyless entry transmitter
Code registration error

Transmitter battery dead

Transmitter faulty

Power door lock and keyless entry system
faultyRegister code
Replace battery
Replace transmitter
Refer to SYSTEM INSPECTION
of POWER DOOR LOCK AND
KEYLESS ENTRY SYSTEM
(IF KEYLESS ENTRY IS
EQUIPPED) in this section
Although any door is
opened within 30 seconds
after power door(s)
unlocked by keyless entry
transmitter, all power
doors are locked again
automatically
Door switch faulty

Wiring harness connected to door switch
brakesReplace switch
Repair
Only one power door is not
locked / unlocked
Wiring or coupler faulty

Actuator (door lock motor) faultyRepair
Replace actuator
Operation distance of
keyless entry is unstable
Transmitter battery dead

Transmitter faultyReplace battery
Replace transmitter

YH4
GRAND
VITARA
Terminal
Switch
Type 1
Type 2
1. Door lock switch
2. Door lock switch coupler
Terminal
Switch
8D-20 WINDOWS, MIRRORS, SECURITY AND LOCKS
POWER DOOR LOCK SYSTEM (IF KEYLESS
ENTRY IS NOT EQUIPPED)
INSPECTION
POWER DOOR LOCK SWITCH
Check for continuity between terminals at each switch position as
shown below.
Type 1
ALK
LOCK
NEUTRAL
UNLOCK
Type 2
ABF
LOCK
OFF
UNLOCK
POWER DOOR LOCK CONTROLLER (CANVAS TOP
MODEL)
1) Disconnect power door lock controller coupler.
2) Connect (+) wire and (±) wire of 12 V battery to terminal ªAº, ªEº
and ªFº as shown in figure.
3) Disconnect cord from terminal ªEº and connect it to terminal ªGº.
4) Repeat Steps 2) and 3) several times and if relay operation is
heard every time, it means that controller is operating.
POWER DOOR LOCK CONTROLLER (HARD TOP MODEL)
1) With the driver side door key turned LOCK, check all power
doors are locked.
2) With the driver side door key turned UNLOCK, check only the
driver side power door is unlocked.
Turn the driver side door key to UNLOCK again within 5 se-
conds, check all power doors are unlocked.
If check result of Step 1) and Step 2) is satisfactory, power door lock
controller is OK. If check result is not satisfactory, go to next Step 3).
3) Disconnect negative cable at battery.
4) Disconnect coupler of power door lock controller.
5) Use a 12 V battery to connect its (+) terminal to terminal E02-1,
and its (±) terminal to terminal E02-2 and E02-3. Check all power
doors are locked.
If check result is not satisfactory, repair circuit and recheck.
If check result is satisfactory, go to next Step 6).

YH4
GRAND
VITARA
Terminal
Key
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-21
6) Connect negative cable at battery.
7) Check that the voltage and resistance between following termi-
nals are specifications.
Terminals
ConditionSpecification
E02-7 and
groundAnytime10 ± 14 V
E02-14 and
groundAnytimecontinuity
E02-8 and
When driver side door key
switch is OFF positionNo continuity
groundWhen driver side door key
switch is LOCK positionContinuity
E02-9 and
When driver side door key
switch is OFF positionNo continuity
groundWhen driver side door key
switch is UNLOCK positionContinuity
If check result is not satisfactory, repair circuit and recheck.
If check result is satisfactory, replace controller.
KEY CYLINDER SWITCH (DRIVER SIDE)
Check for continuity between terminals according to the key action
shown below.
321
LOCK
OFF
UNLOCK

YH4
GRAND
VITARA
WINDOWS, MIRRORS, SECURITY AND LOCKS 8D-23
POWER DOOR LOCK AND KEYLESS ENTRY SYSTEM (IF KEYLESS ENTRY IS
EQUIPPED)
SYSTEM INSPECTION
STEPACTIONYESNO
1Check power door lock operation referring to its
INSPECTION in this section.
Is this operation OK?Go to Step 2.Go to Step 3.
2Check keyless entry operation referring to its
INSPECTION in this section.
Is this operation OK?Go to Step 4.Go to Step 6.
3Check keyless entry operation referring to its
INSPECTION in this section.
Is this operation OK?Go to Step 5.Go to Step 7.
4Check hazard warning lights operation referring to
its INSPECTION in this section.
Is this operation OK?This system is OK.Go to Step 10.
5Check door lock key and power door lock switch
circuit referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.
And go to Step 4.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
And go to Step 4.
6Check ignition switch and door switch circuit
referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.
And go to Step 4.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
And go to Step 4.
7Check power door lock actuator circuit referring to
its INSPECTION in this section.
Is this circuit OK?Go to Step 8.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
If OK, go to Step 4.
If not OK, go to next
Step 8.
8Check power supply and grounding circuit
referring to its INSPECTION in this section.
Is this circuit OK?Go to Step 9.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
If OK, go to Step 4.
If not OK, go to next
Step 9.
91) Check door lock key and power door lock
switch circuit referring to its INSPECTION in
this section.
2) Check ignition switch and door switch circuit
referring to its INSPECTION in this section.
Are these circuits OK?Replace controller and
recheck.
And go to Step 4.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
And go to Step 4.

YH4
GRAND
VITARA
8D-24 WINDOWS, MIRRORS, SECURITY AND LOCKS
STEPACTIONYESNO
10Check that hazard warning lights flash with hazard
switch ON.
Is check result OK?Go to Step 11.Refer to ªTurn Signal
and Hazard Warning
Lightsº in DIAGNOSIS
and repair.
And go to Step 4.
11Check door knob switch and turn signal relay
circuit referring to its INSPECTION in this section.
Is this circuit OK?Replace controller and
recheck.Repair circuit referring
to WIRING DIAGRAM
MANUAL and recheck.
POWER DOOR LOCK OPERATION
INSPECTION
1) With the driver side door key turned LOCK, check all power
doors are locked.
2) With the driver side door key turned UNLOCK, check only the
driver side power door is unlocked.
Turn the driver side door key to UNLOCK again within 5 se-
conds, check all power doors are unlocked.
If check result of Step 1) and Step 2) is satisfactory, this operation
is OK.
KEYLESS ENTRY OPERATION
INSPECTION
1) With the IG switch OFF and all doors closed, push LOCK button
on transmitter. Check all power doors are locked.
2) Push UNLOCK button on transmitter. Check only driver side
power door is unlocked.
3) Push UNLOCK button on transmitter again within 5 seconds.
Check all power doors are unlocked.
But if any door is not opened within 30 seconds after power
door(s) unlocked, all power doors are locked again automatical-
ly.
If check result of Step 1) to Step 3) is satisfactory, this operation is
OK.
HAZARD WARNING LIGHTS OPERATION
INSPECTION
1) Check that hazard warning lights flash one time when power
doors are locked by pushing LOCK button on transmitter.
2) Check that hazard warning lights flash two times when power
door(s) is (are) unlocked by pushing UNLOCK button on trans-
mitter.
If check result of Step 1) and Step 2) is satisfactory, this operation
is OK.