2000 SUBARU OUTBACK service

Maintenance and service11-35
–
CONTINUED –
HB4001CB
Tires and wheels
WARNING
When replacing a tire, make sure you use only the same size,
circumferences, construction, brand, speed symbol and load in- dex as the original tires listed on the tire placard. Using othersizes, circumferences or construction may result in severe me-
chanical damage to the drivetrain of your vehicle and may affectride, handling, braking, speedometer/odometer calibration, and
clearance between the body and tires. It also may be dangerousand lead to loss of vehicle control. Do not use a combination of radial, belted bias or bias tires
since it may cause dangerous handling characteristics and leadto an accident. Do not let air out of warm tires to adjust pressure. Doing so
will result in low tire pressure.
The tires should b e c hec ked freq uently for p rop er t ire p ressure, wear,
and c uts.

Maintenance and service11-37
–
CONTINUED –
OM-H0231
New tread Worn tread
OM-H0230
Tread wear indicator
A tire should b e rep lac ed when the tread wear ind ic ator ap p ears as a
solid b and ac ross the tread . The ind ic ators ap p ear when the remaining
tread has b een worn to 0.063 in (1.6 mm) or less. Wheel covers Removing the wheel cover
OM-H2454
Insert the wheel nut wrenc h into the notc h p rovid ed , and p ry the
wheel c over off.

Maintenance and service11-39
–
CONTINUED –

When wheel nuts, b alanc e weig hts, or the c enter c ap rep lac ed , b e
sure to rep lac e them with g enuine SUBARU p arts d esi g ned for aluminum
wheels.
Windshield washer fluid
CAUTION
Never use engine coolant as washer fluid because it could cause paint damage.
Chec k the level of the washer fluid at eac h fuel st op . If the level is low, fill
the fluid up to the nec k of the reservoir.
Use wind shield washer fluid . If wind shield washer f luid is unavailab le use
c lean water.
In areas where water freezes in winter, use an anti -freeze typ e wind shield
washer fluid . SUBARU Wind shield Washer Fluid c ontai ns 58.5% methyl
alc ohol and 41.5% surfac tant, b y volume. Its freezi ng temp erature varies
ac c ord ing to how muc h it is d iluted , as ind ic ated b elow.
Washer Fluid Conc entration
Freezing Temp erature
30% 50%
100%10.4 F ( –12 C)
–4 F ( –20 C)
–49 F ( –45 C)
HBB004IA

Maintenance and service11-41
–
CONTINUED –
HS0191
Metal support
4. If the new b lad e rub b er is not p rovid ed with two metal sp ines, remove
the metal sp ines from the old b lad e rub b er and inst all them in the new
b lad e rub b er.
HS0192
Metal spines
5. Alig n the c laws of the metal sup p ort with the g ro oves in the rub b er
and slid e the b lad e rub b er assemb ly into the metal sup p ort until it loc ks.
Be sure to p osition the c laws at the end of the met al sup p ort b etween the
stop p ers on the rub b er as shown. If the rub b er is n ot retained p rop erly,
the wip er b lad e may sc ratc h the wind shield .

Maintenance and service11-43
–
CONTINUED –
and other metal jewelry. Never allow metal tools to contact the
positive battery terminal and anything connected to it WHILE youare at the same time in contact with any other metallic portion ofthe vehicle because a short circuit will result.
Keep everyone including children away from the battery.
Charge the battery in a well-ventilated area.
CAUTION
Never use more than 10 amperes when charging the battery be-
cause it will shorten battery life.
It is unnec essary to p eriod ic ally c hec k the b attery fluid level or p eriod i-
c ally refill with d istilled water. Fuses
CAUTION
Never replace a fuse with one having a higher rating or with mate-
rial other than a fuse because serious damage or a fire could re-sult.
HBB008CBHB8003CA
The fuses are d esig ned to melt d uring an overload t o p revent d amag e to
the wiring harness and elec tric al eq uip ment. The fu ses are loc ated in

Maintenance and service11-45
–
CONTINUED –
4. Pull out the fuse with the fuse p uller.
5. Insp ec t the fuse. If it has b lown, rep lac e it wit
h a sp are fuse of the
same rating .
6. If the same fuse b lows ag ain, this ind ic ates that its system has a
p rob lem. Contac t your SUBARU d ealer for rep airs.
Main fuse and fusible link
HB8003CB
The main fuses and fusib le link are d esig ned to mel t d uring an overload
to p revent d amag e to the wiring harness and elec tri c al eq uip ment.
Chec k the main fuses and fusib le link if any elec tr ic al c omp onent fails to
op erate (exc ep t the starter motor) and other fuses are g ood . A melted
main fuse or fusib le link must b e rep lac ed . Use onl y rep lac ements with
the same sp ec ified rating as the melted main fuse o r fusib le link. If a
main fuse or fusib le link b lows after it is rep lac e d , have the elec tric al sys-
tem c hec ked b y your nearest SUBARU d ealer.
Installation of accessories
Always c onsult your SUBARU d ealer b efore installing fog lig hts or any
other elec tric al eq uip ment in your vehic le. Suc h ac c essories may c ause
the elec tronic system to malfunc tion if they are in c orrec tly installed or if
they are not suited for the vehic le.

Maintenance and service11-47
–
CONTINUED –
Wattag e Bulb No.
8 Bac kup lig ht
Sed an 12V –27W 3156K
Station wag on 12V –27W 1156
9 Lug g ag e area lig ht 12V –13W —
Q Hig h mount stop lig ht
Sed an 12V –18W 921
Station wag on 12V –13W 912
W Rear turn sig nal lig ht
Sed an 12V –21W —
Station wag on 12V –21W R2172 7440
E Brake/tail lig ht
Sed an 12V –27/8W 3157K
Station wag on 12V –27/8W 1157
R Lic enc e p late lig ht
Sed an 12V –5W 168
Station wag on 12V –3.8W or 5W 194 or 168
T Trunk room lig ht 12V –5W W5W
HBF013FC
HBB033BC

Maintenance and service11-49
–
CONTINUED –
n
Low beam light bulbs
HBB042BA
HBB041BB
1. Disc onnec t the elec tric al c onnec tor for the b lac k c ab le.
2. Remove the retainer sp ring .
3. Rep lac e the b ulb , then set the retainer sp ring se c urely.
4. Rec onnec t the elec tric al c onnec tor for b lac k c ab l e.
5. Install the head lig ht b ulb c over. n High beam light bulbs
HBB044BB
HBB043BA
1. Disc onnec t the elec tric al c onnec tor from the b ulb .
2. Remove the b ulb from the head lig ht assemb ly b y tu rning it c oun-
terc loc kwise.
3. Rep lac e the b ulb with new one.
4. Rec onnec t the elec tric al c onnec tor. At this time, use c are not to
touc h the b ulb surfac e.