2000 SKODA FABIA instrument panel

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 5 02
Resetting service interval display (SID) with
-V.A.G 1552- (QG0)
–Connect -V.A.G 1552-.
–Switch on ignition.
–Enter address word 17 „Dash Panel Insert“ and con-
firm with .
–Press key.
Readout on display (e.g.):
–Press key.
Readout on display:
–Enter function 10 „Adaptation“ and confirm with the
key.
Readout on display:
–Select adaptation channel of the service event to be
reset: for display „service OIL“ channel 10; for display
„service INSP“ channel 10, 11 and 12.
♦Entry of the relevant adaptation value for the short
journey counter can only be made in steps of 100 km;
consequently the read-out in the display is also in
units of 100 km.
♦Adaptation values must be entered as a 5-digit
number (e.g. 00150 for adaptation value 150, equals
a distance of 15 000 km to the next service event).
♦The value entered is counted back to 0 km.
♦The time counter for the „INSP service“ can be adapt-
ed with a maximum of 370 days.
♦Only a direct data entry is possible using the keypad
of the vehicle system tester!
♦If an incorrect figure is entered the „Adaptation“ func-
tion is terminated and must be adapted again.
Example:
Resetting SID for „OIL service“:
Readout on display:
6Y1919870B COMBIINSTRUMENT VDO X09 ->
Coding 20141 WSC 12345
Q

TMBMC46Y0Y7000001 SKZ7Z0W0204038 ->


Vehicle system test HELP
Select function XX
Q
Adjustment
Enter channel number XX
Service
eventad-
just-
ment
chan
nelCounter con-
tentsAdaptation
value
OIL 10 Distance in 100
km00150
INSP 11 Distance in 100
km00300
INSP 12 Time in days 00370
Note
Channel 10 Adjustment 1 ->
actual value OIL in 100 km - -

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 8 02
Resetting service interval display (SID) with
-V.A.G 1552- (QG1, QG2)
–Connect -V.A.G 1552-.
–Switch on ignition.
–Enter address word 17 „Dash Panel Insert“ and con-
firm with .
Readout on display (e.g.):
–Note the dash panel insert coding.
–Press key.
Readout on display (e.g.):
–Press key.
Readout on display:
–Enter address word 10 „Adaptation“ and confirm with
the key.
Readout on display:
–Enter adjustment channel 02.
Readout on display:
–Press .
Readout on display:
–Enter adaptation value 00000.
Readout on display:
–Confirm the entry with key .
Read-out on display after entering adaptation value
00000:
–Confirm the entry with key .
Readout on display:
–Confirm the entry with key .
Readout on display:
–Press key.
Readout on display:
–Enter 06 for „End output“.
Readout on display:
–Confirm the entry with key .
–Switch off ignition.
Resetting service interval display (SID) without
-V.A.G 1552- (QG1, QG2)
–Switch off ignition.
Q
6Y1919870B COMBIINSTRUMENT VDO X09 ->
Coding 03111 WSC 12345

TMBMC46Y0Y7000001 SKZ7Z0W0204038 ->


Vehicle system test HELP
Select function XX
Q
Adjustment
Enter channel number XX
Channel 2 Adaptation 1
- -

Channel 2 Adaptation 1
Enter adjustment value XXXXX
Channel 2 adjustment 1 Q
Enter adaptation value 00000
Q
Channel 2 adjustment 0 Q
- -
Q
Channel 2 adjustment 0 Q
Store changed value?
Q
Channel 2 Adaptation 0
Changed value stored

Vehicle system test HELP
Select function XX
Vehicle system test HELP
06 - End output
Q

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 10 02
–Connect -V.A.G 1552-.
–Switch on ignition.
–Enter address word 17 „Dash Panel Insert“ and con-
firm with .
Readout on display (e.g.):
–Note the dash panel insert coding.
–Press key.
Readout on display (e.g.):
–Press key.
Readout on display:
–Enter function 07 „Code control unit“ and confirm with
key.
Readout on display:
–Enter dash panel insert coding which is identical to the
original coding. The value on the fourth position must,
however, be altered from 1 to 2.
XXX1X - QG1
XXX2X - QG2
Readout on display (e.g.):
–Confirm the entry with key .
Readout on display (e.g.):
–Press key.
Readout on display (e.g.):
–Press key.
Readout on display:
–Enter 06 for „End output“.
Readout on display:
–Confirm the entry with key .
–Switch off ignition.
–Switch off -V.A.G 1552-.
Inspecting headlight beam setting and
adjusting if necessary
Special tools, test and measuring equipment and
auxiliary items required
♦Headlight beam setting device
In principle the following inspection and setting descrip-
tion applies for all countries. However, comply with na-
tional guidelines and legislation of the relevant country.
⇒Operating instructions for the headlight beam setting
device
Q
6Y1919870B COMBIINSTRUMENT VDO X09 ->
Coding 03111 WSC 12345

TMBMC46Y0Y7000001 SKZ7Z0W0204038 ->


Vehicle system test HELP
Select function XX
Q
Coding control unit
Enter code number XXXXX (0-32767)
Coding control unit
Enter code number 03121 (0-32767)
Q
6Y1919870B COMBIINSTRUMENT VDO X09 ->
Coding 03121 WSC 12345

TMBMC46Y0Y7000001 SKZ7Z0W0204038 ->


Vehicle system test HELP
Select function XX
Vehicle system test HELP
06 End output
Q

Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
MiscellaneousEdition 06.01
S00.5301.06.2002-9 page 2 02
–As soon as the engine starts, press clutch and remove
gear to avoid driving into the towing vehicle.
Do not start the engine of vehicles fitted with an exhaust
catalyst by towing over a long distance as unburnt fuel
may get into the catalyst and burn there. This may result
in overheating and hence in the destruction of the cata-
lyst.
Perform a test drive
The following must be assessed within the scope of a test
drive according to the vehicle equipment and the availa-
ble possibilities (city/country, weather)
–Inspect engine for performance, misfiring, idling be-
haviour and acceleration.
–Foot and handbrake: Functional test (jerking, squeak-
ing, pulling to one side) ABS operation. Brake pedal-
idle travel: max.
1/3 of the idle travel.
–Inspect the lever position and smooth operation of the
gearshifts.
–Inspect the driving behaviour of the clutch as well as
the pedal force and smell.
–Inspect automatic gearbox: Selector lever position,
selector lever lock, shifting behaviour, display indica-
tion in dash panel insert.
–Inspect steering clearance of the vehicle standing on
its wheels, with engine running by turning the steering
wheel one way and then the other (wheels straight
ahead). There must be no play on the steering.
–Inspecting the sun roof operation.
–Pay attention to pulling and to the straigt ahead posi-
tion of the steering wheel during driving.
–Inspect the imbalance of the wheels, drive shafts and
propshafts.
–Inspecting functions: Heating, air conditioning, venti-
lation, instruments and warning lights, mirror adjust-
ment.
–Inspect engine, gearbox, axles, steering, brakes,
clutch, bodywork for abnormal noises
Raising the vehicle
Using a lift platform and a workshop jack
The vehicle must only be raised with a workshop jack in
the indicated jacking points -arrows-.
To avoid damage use a suitable rubber or wood insert.
Note
S02-0316