Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
ChassisEdition 02.04
S00.5301.13.2002-5 page 6 02
Inspecting the tyre tread depth (includ-
ing spare wheel) and entering
This value may differ in individual countries as a result of
differing statutory requirements.
If the tyre tread depth is close to the legal minimum, in
other words if no further tread exists at the points around
the circumference of the tyre at which the 1.6 mm high
wear indicators are positioned, the customer should be
informed of the necessary repair measures.
Tightening wheel bolts to specific torque
Special tools, test and measuring equipment and
auxiliary items required
♦Torque wrench
Tightening torque for steel and light alloy wheels 120 Nm.
Inspecting the tyre inflation pressure (in-
cluding spare wheel) and correcting the
tyre inflation pressure if necessary
Special tools, test and measuring equipment and
auxiliary items required
♦Tyre inflation pressure tester
♦The tyre inflation pressures are indicated on a stick-
er,which is affixed to the inside of the fuel filler flap.
♦The tyre inflation pressures indicated on the sticker
apply only to the tyres when cold. Do not reduce the
higher inflation pressure of warm tyres.
♦If winter tyres are fitted, the relevant tyre inflation pres-
sure should be increased by 0.2 bar/20 kPa.
Tyre inflation pressure table
The instructions in the Workshop Repairs Manual always
have priority over those for the vehicle.
FABIA
Note
Note
Engine TyresTyre inflation pressure (kPa/bar)
Partial load Full load
Front axle Rear axle Front axle Rear axle
1.0 ltr./37 kW
1.2 ltr./40 kW
1.2 ltr./47 kW
1.4 ltr./44 kW
1.4 ltr./50 kW
1.4 ltr./55 kW
1.4 ltr./74 kW
2.0 ltr./85 kW155/80 R13 230/2,3 220/2,2 230/2,3 250/2,5
165/70 R14 210/2,1 200/2,0 210/2,1 260/2,6
185/60 R14 220/2,2 200/2,0 230/2,3 270/2,7
185/55 R15 210/2,1 200/2,0 220/2,2 270/2,7
195/50 R15 210/2,1 210/2,1 230/2,4 270/2,8
205/45 R16 220/2,2 200/2,0 240/2,4 280/2,8
Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
Electrical SystemEdition 09.04
S00.5301.14.2002-6 page 11 02
Test and setting conditions
•Tyre inflation pressure O.K.
•Lenses must neither be damaged nor soiled.
•Reflectors and bulbs O.K.
•Vehicle load must be achieved.
Load: With an individual or 75 kg on the driver's seat in an
otherwise unladen vehicle (dead weight).
The unladen weight is the weight of the vehicle with full
fuel tank (at least 90 %) including the weight of all the op-
erational equipment elements (e.g. spare wheel, tool kit,
jack etc.).
The vehicle must have rolled a few metres or have been
depressed a few times at the front and rear to allow the
springs to settle.
•Both the vehicel and headlight beam setting device
must be on a level flat surface.
•Align the vehicle and headlight beam setting device in
accordance with the device manufaturer's indications.
•Check the control system of vehicles equipped with
headlight beam control by repeatedly turning the
thumbwheel in the dash panel. Then turn the thum-
bwheel to basic position.
•Set the inclination value.
Inclination value:
The inclination value is marked in „%“ at the top of the
headlight housing. The main headlights must be set to
this value. The percentage value applies up to 10 metres
projection distance. This will be 12 cm for an inclination
value of e.g. 1.2 %.
Inspecting headlight beam setting and adjusting
if necessary
Main headlights:
–Check whether the horizontal light/dark limit touches
the separation mark -1- on the test surface when the
low beam light is on .
–Check whether the kink -2- between the left horizontal
part and the ascending right part of the light/dark limit
intersects with the central mark -3- on the vertical line.
The light core of the light beam must be located to the
right of the vertical line.132
S02-0091
Downloaded from www.Manualslib.com manuals search engine FABIA 2000➤Inspection and Maintenance
BodyEdition 09.04
S00.5301.14.2002-7 page 6 02
–Separate filter element from the frame.
Installing:
Installation is carried out in the reverse order.
Sticking the vehicle data sticker
–Stick the vehicle data sticker to the floor of the luggage
compartment inside the vehicle next to the spare
wheel -arrow-.
Inspect trailer coupling
Inspect condition of trailer coupling support
–Inspect condition of cavity of tensioning sleeve.
–Clean cavity of tensioning sleeve and treat with G 052
778 A2.
–Check cap of tensioning sleeve.
If the cap of the tensioning sleeve is missing or damaged,
replace with a new one.
Inspect condition of trailer arm
–Check whether the control lever turns.
If the control lever turns with difficulty or does not turn, the
seized eccentric in the trailer arm housing must be
cleaned and treated with G 052 778 A2. If it is does not
improve, then the trailer arm must be sent back to the
manufacturer for repair or replaced with a new one (repair
measure).
–Check the turning of the key in the lock.
If the securing bolt moves with difficulty or does not move
at all; the reasons for this may be:
♦Lock is defective ⇒ replace bolt with lock (repair
measure)
♦Bent control lever ⇒ must be repaired by the manu-
facturer or replace trailer arm (repair measure)
♦Clean seized bolt ⇒, treat with G 052 778 A2 and
bring into motion. If it is does not improve, then the
trailer arm must be sent back to the manufacturer for
repair or replaced with a new one (repair measure).
S02-0310
S02-0322
