2000 RENAULT SCENIC fuel pressure

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Low pressure pump (supercharging pump)
13
13-21
Low pressure pump (supercharging pump)
The supercharging pump is an electric pump located in
the engine compartment.
REMOVAL
IMPORTANT: take note of the quantity of diesel and
the residual pressure in the pipes.IMPORTANT:
A fuel cock (R) is fitted to the fuel filter at the level of
the return pipe leading to the tank.
It should be in open position for normal operation.
To reprime the circuit after an intervention, a filter
change or a fuel fault you should:
– close the fuel cock (R),
– start the low pressure pump by switching on the
ignition several times,
– start the engine,
– OPEN THE FUEL COCK (the valve is open when the
two coloured lines are aligned).
NOTE: certain vehicles are not fitted with a fuel cock.
In this case, ignore this operation. YOU SHOULD FOLLOW THE CLEANNESS
INSTRUCTIONS CLOSELY.
16776S
16870R3

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Fuel filter
13
13-22
Fuel filter
The fuel filter is located in the engine compartment. It is contained in an unremovable cartridge. This cartridge
contains a regulating valve which limits the flow of diesel circulating to the engine.
To replace the filter it is therefore necessary to replace the whole unit.
REMOVAL
IMPORTANT: take note of the quantity of diesel and
the residual pressure in the pipes.
Disconnect the pipes on the filter which:
– feed the engine (1),
– come from the fuel tank (2) (low pressure pump),
– return to the tank (3) via the fuel cock (depending on
version),
– return from the engine (4),
– which return to the tank via the temperature
exchanger (5).
NOTE: certain vehicles are not fitted with a fuel cock.
In this case, ignore the repriming procedure.REFITTING
It is vital that you respect the position of the
connections to the filter.
Be careful not to squeeze or damage the pipes.
IMPORTANT:
A fuel cock (R) is fitted to the fuel filter at the level of the
diesel return pipe to the tank.
It should be in open position for normal operation.
To reprime the circuit after an intervention, a filter
change or a fuel fault you should:
– close the fuel cock (R),
– start the low pressure pump by switching on the
ignition several times,
– start the engine,
– OPEN THE FUEL COCK (the valve is open when the
two coloured lines are aligned).
It is necessary to periodically bleed the water trapped
in the diesel filter via the bleed plug (6). YOU SHOULD FOLLOW THE CLEANNESS
ADVICE CLOSELY.
15773R
16870R3

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
High pressure pump
13
13-23
High pressure pump
IT IS PROHIBITED TO REMOVE THE INTERIOR OF
THE PUMP.
IMPORTANT: before any intervention, connect the
after-sales diagnostic tool, query the injection
computer and check that the injection rail is not under
pressure.
Take note of the fuel temperature.SPECIAL TOOLING REQUIRED
Mot. 1054 TDC setting pin
Mot. 1200-01 Pump-pulley retaining tool
Mot. 1383 Tool for removing high pressure
pipes
Mot. 1525 Pulley extractor
Mot. 1525-01 Extractor adaptor for F9Q
ESSENTIAL SPECIAL TOOLING
"Low torque" torque wrench
TIGHTENING TORQUES (in daN.m)
High pressure pipe 2.5±0.2
High pressure pump mounting 3.2± 0.3
High pressure pump pulley nut 5 ± 0.5
Suspended mounting cover bolt 6.2 ± 1
Torque reaction arm bolt 15

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
High pressure pump
13
13-24
REMOVAL
Disconnect the battery.
Set the engine to top dead centre using the pin
Mot. 1054.
Release from the fuel filter from its support.
Remove:
– the injection computer mounting,
– the high pressure pulley cover,
– the pump outlet/injection rail inlet pipe using
Mot.1383.
Insert the blanking plugs.
Disconnect the fuel return pipe from the pump and
insert the plugs to maintain cleanness.
Fit tool Mot. 1200-01 on the pulley.Remove the nut from the high pressure pump pulley.
Fit the extractor Mot. 1525 fitted with the adaptor
Mot. 1525-01 on the pulley pump then disassemble
the unit.
Remove the mounting nuts by holding the bolts (1). YOU SHOULD FOLLOW THE CLEANNESS
INSTRUCTIONS CLOSELY
16870S
15872R1
16183R

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
High pressure pump
13
13-26
Reprime the circuit:
– close the fuel cock (R),
– start the low pressure pump while switching on the
ignition several times,
– start the engine,
– OPEN THE FUEL COCK (R) (the valve is open
when the two coloured lines are aligned).
NOTE: certain vehicles are not fitted with a fuel cock.
In this case, ignore the repriming procedure.
16870R3
After any intervention, check that there are no
leaks in the diesel circuit. Start the engine at idling
speed until the fan starts up, then accelerate several
times under no load.

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Injector rail
13
13-27
Injector rail
IMPORTANT: before any intervention, connect the
after-sales diagnostic tool, query the injection
computer and check that the injection rail is not under
pressure.
Take note of the fuel temperature.SPECIAL TOOLING REQUIRED
Mot. 1294 -01 Tool for removing windscreen
wiper arms
Mot. 1383 Tool for removing high pressure
pipes
ESSENTIAL SPECIAL TOOLING
"Low torque" torque wrench
TIGHTENING TORQUES (in daN.m)
High pressure pipe nut 2.5±0.2
Injection rail mounting bolt 2.2±0.2
REMOVAL
Remove (for the Scénic):
– the windscreen wiper arms using tool Elé. 1294-01,
– the scuttle panel,– the bulkhead panel.
Disconnect the flow meter and remove the air unit.
11020R
11036R2

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Injectors
13
13-32
Injectors
IT IS FORBIDDEN TO REMOVE THE INTERIOR OF
AN INJECTOR OR TO SEPARATE THE INJECTOR
HOLDER FROM THE PIPE.
IMPORTANT: before any intervention, connect the
after-sales diagnostic tool, query the injection
computer and check that the injection rail is not under
pressure. Take note of the fuel temperature.SPECIAL TOOLING REQUIRED
Elé. 1294 -01 Tool for removing windscreen
wiper arms
Mot. 1383 Tool for removing high pressure
pipes
TIGHTENING TORQUES (in daN.m)
Injector clamp mounting bolt 2 ± 0.2
High pressure pipe nut 2.5 ± 0.2

Downloaded from www.Manualslib.com manuals search engine DIESEL EQUIPMENT
Injectors
13
13-36
Fit the high pressure pipe.
Loosen the high pressure pump/rail pipe.
Tighten to torque:
– the injector,
– the injector side connections, then the injection rail connections,
– the rail.
– the pump/rail pipe (high pressure pump side under pressure).
NOTE: it is essential that you replace the fuel return pipe placed on the
injectors during removal.
16192S
After any intervention, check that there are no leaks in the diesel circuit.
Start the engine at idling speed until the fan starts up, then accelerate
several times under no load.