2000 MITSUBISHI CARISMA oil dipstick

INSTRUMENTS AND CONTROLS
4–10
CAUTION
(3) If the lamp illuminates or flashes while the
engine is running, avoid driving at high
speeds and have the system checked at
an authorized MITSUBISHI dealer.
During vehicle operation with the lamp il-
luminated or flashing, the vehicle may not
accelerate when you depress the acceler-
ator pedal.
When the vehicle is stationary with the
lamp illuminated or flashing, you must de-
press the brake pedal more firmly than
usual since the engine idling speed is
higher than usual and the vehicle with an
automatic transmission has a stronger
tendency to creep forward.
NOTE
The engine electronic control module accommodat-
ing the onboard diagnostic system has various fault
data (especially about the exhaust emission) stored.
This data will be erased if a battery cable is discon-
nected, which will make rapid diagnosis difficult. Do
not disconnect a battery cable when the check engine
indication lamp is ON.
Oil pressure warning lamp - redED25A-Ai
This lamp illuminates when the ignition key is turned
“ON”, and goes off after the engine has started. If it il-
luminates while the engine is running, the oil pressure
is too low.
If the warning lamp illuminates while the engine is run-
ning, turn the engine off and contact your nearest
authorized MITSUBISHI dealer for inspection.
CAUTION
(1) If this lamp illuminates when the engine
oil level is not low, contact your nearest
authorized MITSUBISHI dealer for inspec-
tion.
(2) This warning lamp does not indicate the
amount of oil in the crankcase. This must
be determined by checking the oil level on
the dipstick, while the engine is switched
off.
(3) If you continue driving with low engine oil
level or with this warning lamp illumi-
nated, engine seizure may occur.
NOTE
The oil pressure warning lamp should not be treated
as an indication of the engine’s oil level. The oil level
must be checked using the dipstick.

MAINTENANCE
9–3
Petrol-powered vehicles (1600, 1800 models)
M03A027a
This check must be carried out with the ve-
hicle on a flat level surface with the engine at
normal operating temperature, but NOT run-
ning. If the engine has been running, wait for
a few minutes to allow the engine oil to return
to the oil pan to ensure an accurate
measurement.
Remove the dipstick and wipe it with a clean
cloth, re - insert the dipstick as far as it will go.
Remove the dipstick and check the oil level.
This should always be within the range as
indicated.
If the oil level is below the specified limit, re-
move the filler cap and add oil. Then recheck
the level. When satisfied that the level is cor-
rect, refit the oil filler cap making sure that it
is securely fitted.
Diesel-powered vehicle
M03A090a
Use only the recommended oils with an API
or ACEA classification as specified in this
manual.
NOTE
(1)Engine oil consumption is greatly in-
fluenced by payload, engine speed,
etc. It may reach 1.0 lit./1,000 km de-
pending on style of driving.
(2) The engine oil will deteriorate rapidly if
the vehicle is subjected to severe condi-
tions (for example, repeated operation
on rough roads, in mountainous re-
gions, on roads with many uphill and
downhill gradients, or over short dis-
tances). Consequently, the oil will re-
quire earlier replacement.
(3) For handling of used engine oils, refer to
page
1–11.
Petrol-powered vehicles
M03B037a
Selection of engine oil
(petrol-powered vehicle)
EM03B-Of
(1) Select engine oil of the proper SAE vis-
cosity number according to the atmos-
pheric temperature.
For 0W-30, 5W-30, 0W-40 and 5W-40
viscosity grade, use only ACEA A3
classification.
(2) Use engine oil conforming to the follow-
ing classification:

ACEA classification:
“For service A1, A2 or A3”

API classification:
“FOR SERVICE SG” or higher
NOTE
Use of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It
may result in failure of the mechanical as-
sembly.

MAINTENANCE
9–4
Type 1
M03B029a
Selection of engine oil
(diesel-powered vehicles)
EM03BAKe
(1) Select engine oil of the proper SAE vis-
cosity number according to the atmos-
pheric temperature.
(2) Use engine oil conforming to the follow-
ing classification:
Ty p e 1 :ACEA classification:
“For service B2-96 or B3-96”
Ty p e 2 :API classification:
“For service CF”
NOTE
Use of additives is not recommended
since they may reduce the effectiveness of
additives already included in the engine
oil. It may result in failure of the mechani-
cally assembly.
Type 2
M03B030aM05A069a
Automatic transmission fluid*EM05AAH
The proper amount of automatic trans-
mission fluid is essential to the life and oper-
ation of the automatic transmission. Either in-
sufficient fluid or excessive fluid could cause
transmission trouble. The transmission fluid
filler port cap is equipped with a dipstick. Use
the following procedure to check the fluid
level.
1. Check the fluid level after the vehicle
has been driven enough to warm up
the transmission fluid.
2. Park the vehicle on a flat, level surface
and apply the parking brake.

MAINTENANCE
9–5
3. With the engine idling and the brake
pedal fully depressed, move the trans-
mission selector lever through all the
positions from the ”P” (PARK) to ”L”
(LOW) (with INVECS–II 4A/T), the ”P”
(PARK) to ”D” (DRIVE) (with INVECS–
II Sports Mode 4A/T), stopping mo-
mentarily at each position.
4. Move the selector lever to the ”N”
(NEUTRAL) or ”P” (PARK) position.
5. Remove the dipstick and wipe it with a
clean lint–free cloth.
6. Reinsert the dipstick as far as it goes.
7. Remove the dipstick and read the oil
level. The fluid level should always be
between the two marks on the dip-
stick.
8. Use only the following transmission
fluid to ensure optimum transmission
performance: ”DIA QUEEN ATF SP
III”.
WARNING
Do not spill the fluid onto a hot ex-
haust manifold during topping up or
inspection, or a fire may occur.
Petrol–powered vehicles
N26A034a
Engine coolantEM36ALY
A translucent coolant reserve tank is located
in the engine compartment. The coolant
level in this tank should be kept between the
two marks on the reserve tank when
measured while the engine is cold. The cool-
ing system is a closed system and normally
the loss of coolant should be very slight. A
noticeable drop in the coolant level could
indicate leakage. If this occurs, have the sys-
tem checked at an authorized MITSUBISHI
dealer as soon as possible.
If the level should drop below the ”LOW”
level on the reserve tank, open the lid and
add coolant.
Also, if the reserve tank is completely empty,
remove the radiator cap and add coolant
until the level reaches the filler neck.
Diesel–powered vehicles
N26A160a
NOTE
On diesel–powered vehicles, the radiator
has no filler port. Supply coolant from the filler
port in the reserve tank.
WARNING
Do not open the reserve tank lid or
radiator cap while the engine is hot.
The coolant system is under pressure
and any hot coolant escaping could
cause severe burns.