2000 MITSUBISHI CARISMA oil

GENERAL INFORMATION
1–11
Used engine oils safety
instructions
EB12A-B
WARNING
(1) Prolonged and repeated contact
may cause serious skin disorders,
including dermatitis and cancer.
(2) Avoid contact with the skin as far
as possible and wash thoroughly
after any contact.
(3) Keep used engine oils out of reach
of children.
Protect the environment
It is illegal to pollute drains, water courses
and soil. Use authorized waste collection fa-
cilities, including civic amenity sites and ga-
rages providing facilities for disposal of used
oil and used oil filters. If in doubt, contact your
local authority for advice on disposal.
Driving and alcoholEB25A-Aa
Driving under the influence of alcohol is one
of the most frequent causes of accidents.
Your driving ability can even be seriously im-
paired with blood alcohol levels below the le-
gal maximum. If you are drinking, don’t drive.
Ride with a designated non-drinking driver,
call a cab, a friend, or use public transporta-
tion.
WARNING
Driving after drinking can lead to an
accident. Your perceptions are less
sharp, your reflexes are slower, and
your judgement is impaired when you
have been drinking.
NEVER DRINK AND THEN DRIVE.
Safe driving techniquesEB26A-Di
Driving safety and protection against injury
cannot be fully ensured. However, we rec-
ommend that you pay extra attention to the
following:
(1) Before starting the vehicle, make sure
that you and your passengers have fas-
tened your seat belts.
(2) Never leave your vehicle unattended
with the key in the ignition and children
inside the vehicle. Children may play
with the driving controls and this could
lead to an accident.
(3) Make sure that infants and small
children are properly restrained in ac-
cordance with the laws and regulations,
and for maximum protection in case of
an accident.
(4) Switch off the engine if you stop for a
short sleep. If the engine is left running
while you sleep, unexpected vehicle
operation or other accidents may be
caused by unconsciously moving the
shift lever (selector lever on automatic
transmission vehicles) or pressing the
accelerator pedal. If you inadvertently
keep the accelerator pedal pressed, the
engine may overheat or the engine, ex-
haust pipe, etc. may be abnormally
overheated, resulting in an accidental
fire. If poorly ventilated, there is a risk of
poisoning by exhaust gases.

INSTRUMENTS AND CONTROLS
4–6
D50A532d
A: Petrol-powered vehicle
B: Diesel-powered vehicle
Indication and warning lampsED50AMFe1-Turn - signal indication lamps/Hazard warning lamps
2-Automatic transmission indication lamp
(vehicles with A/T only, “N” indicator lamp is used also as A/T
warning lamp.)
Page 5–18
3-High - beam indication lamp
4-Low fuel warning lamp
5-Front fog lamp indication lamp*
6-Rear fog lamp indication lamp
7-Door ajar warning lamp
8-ABS warning lamp*
Page 5–28
9-Brake warning lamp
10 -HOLD indication lamp (vehicle with automatic transmission IN-
VECS-II 4A/T only)
Page 5–20
11-Supplemental restraint (SRS) warning lamp
Page 3–36
12 -Oil pressure warning lamp13 -Charge warning lamp
14 -TCL indication lamp*
Page 5–34
15 -Check engine indication lamp
16 -Cruise control indication lamp*
Page 5–35
17 -Diesel preheat indication lamp
(diesel-powered vehicles only)
18 -Overheating warning lamp
(diesel-powered vehicles only)
NOTE
To find information concerning the indication or warning lamps
marked by the symbol “
Page xx”, refer to the specified pages. For
the other indication and warning lamps, refer to the subsequent
pages.

INSTRUMENTS AND CONTROLS
4–10
CAUTION
(3) If the lamp illuminates or flashes while the
engine is running, avoid driving at high
speeds and have the system checked at
an authorized MITSUBISHI dealer.
During vehicle operation with the lamp il-
luminated or flashing, the vehicle may not
accelerate when you depress the acceler-
ator pedal.
When the vehicle is stationary with the
lamp illuminated or flashing, you must de-
press the brake pedal more firmly than
usual since the engine idling speed is
higher than usual and the vehicle with an
automatic transmission has a stronger
tendency to creep forward.
NOTE
The engine electronic control module accommodat-
ing the onboard diagnostic system has various fault
data (especially about the exhaust emission) stored.
This data will be erased if a battery cable is discon-
nected, which will make rapid diagnosis difficult. Do
not disconnect a battery cable when the check engine
indication lamp is ON.
Oil pressure warning lamp - redED25A-Ai
This lamp illuminates when the ignition key is turned
“ON”, and goes off after the engine has started. If it il-
luminates while the engine is running, the oil pressure
is too low.
If the warning lamp illuminates while the engine is run-
ning, turn the engine off and contact your nearest
authorized MITSUBISHI dealer for inspection.
CAUTION
(1) If this lamp illuminates when the engine
oil level is not low, contact your nearest
authorized MITSUBISHI dealer for inspec-
tion.
(2) This warning lamp does not indicate the
amount of oil in the crankcase. This must
be determined by checking the oil level on
the dipstick, while the engine is switched
off.
(3) If you continue driving with low engine oil
level or with this warning lamp illumi-
nated, engine seizure may occur.
NOTE
The oil pressure warning lamp should not be treated
as an indication of the engine’s oil level. The oil level
must be checked using the dipstick.

STARTING AND DRIVING
5–28
Anti–lock brake system
(ABS)*
EI24ACA
Environmental conditions can have an effect
on braking. During sudden braking when
there is snow, ice, oil, water etc. on the road
surface, a skid may occur. I n this situation,
steering control and braking effectiveness is
reduced and the stopping distance is in-
creased. The vehicle may also go into an un-
controlled spin.
The ABS helps prevent the wheels from
locking during braking, thus maintaining
directional stability, ensuring controllability
and providing optimum braking force.
Driving hints
(1) With ABS fitted, steering during sudden
braking (when the ABS functions) differs
slightly from when the brakes are not
being applied.
Steer the vehicle carefully in these
conditions.(2) Always maintain the same distance
from the vehicle in front of you as you
would for a vehicle not equipped with
ABS. Compared with vehicles not fitted
with ABS, your vehicle may require a
longer stopping distance in the following
cases:

Driving on gravel or snow–covered
roads.

Driving with tyre chains installed.

Driving on roads where the road
surface is pitted or has other differ-
ences in surface height.

Driving on bumpy roads or other
poor driving surfaces.
(3) Operation of ABS is not restricted to
situations where brakes are applied
suddenly. This system may also oper-
ate to prevent wheel lock when you are
driving over manholes, steel road–work
plates, or the vehicle is driven over
steps or level differences in the road,
road markings, or other surfaces which
are difficult for the wheels to grip.
(4) When the ABS is activated, you may
feel the brake pedal pulsating and hear
a characteristic noise. Also at this time,
it may feel as if the pedal attempts to re-
sist being depressed.
In this situation, to let the ABS work
for you, just hold the brake pedal
down more firmly. Do not pump the
brake. This will result in reduced
braking performance.
CAUTION
(1) Even the ABS can not prevent the
natural laws of physics from act-
ing on the vehicle. It cannot for in-
stance avoid accidents that may
result from excessive speed on
bend or following another vehicle
too closely, or aquaplaning. It
should remain the driver’s task to
observe safety precautions to
judge speeds and brake applica-
tions correctly in such condi-
tions.
(2) Be sure to use tyres of the same
type and size on four wheels.
If tyre types or sizes are mixed,
ABS may not function normally.
(3) Never install a limited slip differ-
ential, which is not MITSUBISHI
Genuine parts, as the ABS may
not function normally.
Please consult an authorized
MITSUBISHI dealer.

FOR PLEASANT DRIVING
6–27
Handling of cassette tapesEH02B-Ad
CAUTION
To maintain the cassette tape player
in good condition, observe the follow-
ing precautions.
(1) Do not use cassette tapes longer
than C-90, otherwise sound qual-
ity and tape durability will be
greatly diminished.
(2) Keep the cassette tape in its case
to protect it from tape looseness
and dust when it is not used.
(3) Keep the cassette tape away from
direct sunlight, heat and magnet-
ic fields such as the radio
speakers.
(4) Before inserting the cassette,
make sure that the label is ad-
hered securely to the cassette.
(5) A loose tape should be corrected
before use.
CAUTION
(6) Do not oil any part of the player
and do not insert any object other
than tape cassettes into the slot,
or the tape player may be dam-
aged. Also, avoid inserting your
fingers into the slot. There is a
danger of being burned by the hot
internal parts.
H12F004a
Handling of compact discsEH12E-Ah
(1) This CD player allows use of only the
compact discs with the mark shown in
the illustration above.
(Playback of CD–R discs may cause
problems. CD–RW discs cannot be
played.)
The use of heart-shaped, octagonal, or
any other non-circular discs will result in
the CD player being damaged.
(2) When the temperature suddenly rises,
i.e. immediately after the heater is
turned on in cold weather, dew con-
densation on the disc or in the player
might occur resulting in failure of oper-
ation. In such a case, allow some time
before use.
(3) When the CD player is subjected to viol-
ent vibration as during off-road driving,
detracking may result.

VEHICLE CARE
7–3
Genuine leather*EK27A-Ac
1. Lightly wipe off with gauze or other soft
cloth soaked with a 5 % aqueous sol-
ution of neutral detergent for wool.
2. Dip cloth in fresh water and wring it out
well. Using this cloth, wipe off the de-
tergent thoroughly.
3. Apply leather protecting agent to the
genuine leather surface.
NOTE(1) If genuine leather is wet with water or is
washed in water, wipe off water as
quickly as possible with a dry, soft cloth.
(2) Slight stains on genuine leather may be
removed with leather cleaner as well.
(3) The genuine leather surface may be
damaged if a nylon brush or synthetic
fibre is rubbed hard against it.
(4) Organic solvents such as benzine, al-
cohol and gasoline, acid or alkaline sol-
vents may discolour the genuine leather
surface. Be sure to use neutral deter-
gents.
(5)Dirty genuine leather seat may mildew.
Be very careful about oil stains and re-
move them quickly.
(6) The genuine leather surface may
harden and shrink if it is exposed to di-
rect rays of the sun for long hours. When
your vehicle is parked, place it in the
shade as much as possible.(7) When the temperature of the vehicle in-
terior rises in summer, vinyl products left
on the genuine leather seat may de-
teriorate and stick to the seat.
UpholsteryEK25A-Aa
1. To maintain the value of your new ve-
hicle, handle the upholstery carefully
and keep the interior clean.
Use a vacuum cleaner and brush to
clean the seats. If stained, vinyl and
synthetic leather should be cleaned
with an appropriate cleaner, and cloth
fabrics can be cleaned with either up-
holstery cleaner or a 3 % solution of
neutral detergent in lukewarm water.
2. Clean the carpeting with a vacuum
cleaner and remove any stains with
carpet cleaner. Oil and grease can be
removed by lightly dabbing with a
clean colourfast cloth and stain re-
mover.
Cleaning the outside of your
vehicle
EK28A-Ah
If the following is left on your vehicle, it may
cause corrosion, discolouration and stains,
wash the vehicle as soon as possible.

Seawater, anti-freeze for road use.

Soot and dust, iron powder from fac-
tories, chemical substance (acids, al-
kalis, coal-tar, etc.).

Droppings from birds, carcasses of in-
sects, tree sap, etc.

VEHICLE CARE
7–6
Servicing of plastic partsEK29AMEc
Use a sponge or chamois leather.
If a car wax adheres on a grey or black rough
surface of the bumper, moulding or lamps,
the surface becomes white. In such a case,
wipe it off using lukewarm water and soft
cloth or chamois leather.
CAUTION
(1) Do not use a scrubbing brush or
other hard tools as they may dam-
age the plastic part surface.
(2) Do not use wax containing com-
pound (polishing powder) which
may damage the plastic part sur-
face.
(3) Do not bring the plastic parts into
contact with brake fluids, engine
oils, greases, paint thinners,
painting, and sulphuric acid (bat-
tery electrolyte) which may stain,
or discolour the plastic parts.
If they touch the plastic part, wipe
them off with soft cloth, chamois
or the like and an aqueous sol-
ution of neutral detergent, then
immediately rinse the affected
parts with water.
Aluminium wheels*EK35A-Af
A protective coating is provided over the alu-
minium type wheels.
Clean aluminium wheels with a cleaner de-
signed for use on aluminium and apply an
appropriate protection agent.
NOTE(1) When cleaning aluminium type wheels,
do not use abrasive cleaners. Wheels
exposed to sea water or road chemicals
should be cleaned as soon as possible.
(2) Brushes may damage the aluminium
wheel surface. Always use a sponge,
chamois leather, etc.
(3) Do not apply hot water directly from the
steam cleaner or similar to the wheel
surface.
Window glassEK10A-Ca
The window glass can normally be cleaned
using only a sponge and water.
Glass cleaner can be used to remove oil,
grease, dead insects, etc. After washing the
glass, wipe dry with a clean, dry, soft cloth.
Never use the same cloth to wipe the win-
dow glass as would be used to wipe the
paintwork; wax from the painted surfaces
could adhere to the glass and reduce its
transparency and visibility.
NOTETo clean the inside of the rear window, al-
ways use a soft cloth and wipe the window
glass along the demister heater element so
as not to cause damage.
Wiper bladesEK11A-Aa
Use a soft cloth and glass cleaner to remove
grease, dead insects, etc., from the wiper
blades. Replace the wiper blades when they
no longer wipe properly. (Refer to
page 9–18)

FOR EMERGENCIES
8–11
N24A206a
7. Place the spare wheel and then install
the wheel nuts with the tapered ends
facing inward, then tighten by hand
until the wheel is no longer loose.
NOTE
(1)Flange nuts (2) can be temporarily
used on the steel wheel, but return to
the original wheel and tyre as soon as
possible.
(2)If all four wheels on vehicles with
flange nuts (2) are changed to steel
wheels, use tapered nuts (1).
CAUTION
Never apply oil to either wheel bolts or
nuts as it will cause them to over-
tighten.
N24A014a
8. Lower the vehicle slowly and then
tighten the nuts diagonally in two or
three steps until each nut has been
tightened to the specified torque.
Tightening torque:
98 to 117 Nm
(Achieved by applying force of
approx. 390 to 450N at end of
wheel nut wrench supplied with
vehicle)
CAUTION
Never use extra force with your foot
on the wheel nut wrench or by using
a pipe extension as you can over-
tighten the nut.
9. Lower and remove the jack and stow
the jack, bar, wheel nut wrench and flat
tyre wheel. Have the flat tyre repaired
as soon as possible.