2000 MERCEDES-BENZ C-Class seat

Infant and Child Restraint Systems
We recommend that all infants and children be properly restrained at all times while the vehicle is in
motion. All lap-shoulder belts except driver seat have special seat belt retractors for secure fastening
of child restraints. To fasten a child restraint, use th is seat belt: Follow child restraint instructions for
routing. Then pull shoulder belt out completely and let it retract. During the seat belt retraction a
ratcheting sound can be heard to indicate that the spec ial seat belt retractor is activated. The belt is
now locked. Push down on child restraint to take up any slack. To deactivate, release seat belt
buckle and let seat belt retract completely. The seat belt can again be used in the usual manner.

Warning !
Never release the seat belt buckle while vehicle is in motion, since the special seat belt
retractor will be deactivated.

Important !
The use of infant or child restraints is required by law in all 50 states and all Canadian provinces.
Infants and small children should be seated in an approp riate infant or child restraint system properly
secured by a lap-shoulder belt, and that complies with U.S. Federal Motor Vehicle Safety Standard
213 and Canadian Motor Vehicle Safety Standard 213. A statement by the child restraint
manufacturer of compliance with this standard ca n be found on the instruction label on the restraint
and in the instruction manual provided with the re straint. When using any infant or child restraint
system, be sure to carefully read and follow all manu facturer's instructions for installation and use.
Please read and observe warning labels affixed to inside of vehicle.


Children 12 years old and under must never ride in the front seat, except in a Mercedes-Benz
authorized BabySmart™ compatible child seat, which operates with the BabySmart™ system
installed in the vehicle to deactivate the passenger side front airbag when it is properly
installed. Otherwise they will be struck by the airbag when it inflates in a crash. If this
happens, serious or fatal injury will result.
According to accident statistics, children are safer when properly restrained in the rear
seating positions than in the front seating positions. Infants and small children must ride in
back seats and be seated in an infant or child restraint system, which is properly secured
with the vehicle's seat belt, fully in accordan ce with the seat manufacturer's instructions.
Infants and small children should never share a seat belt with another occupant. During an
accident, they could be crushed between the occupant and seat belt. Children too big for
child restraint systems must ride in back seats using regular seat belts. Position shoulder
belt across chest and shoulder, not face or neck. A booster seat is necessary to achieve
proper belt positioning for children from 41 Ibs. to the point where a lap/shoulder belt fits
properly without one.
When the child restraint is not in use, remove it from the car or secure it with the seat belt to
prevent the child restraint from becoming a projectile in the event of an accident.

U.S.A. Models only:
Since 1986 all U.S. child restraints comply with U. S. regulations without the use of a tether strap.
Canada Models only: This vehicle is provided with tether anchorages for a top tether strap. Consult
your authorized Mercedes-Benz dealer for installa tion of these anchorages. In compliance with
Canadian Motor Vehicle Safety Standard 210.1, ch ild restraint tether anchorage hardware is
attached to the tool kit located in the trunk.

Enlarged Cargo (Option)




1. Locking handle, left backrest
2. Locking handle, right backrest



3. Indicator, right backrest lock,
visible in unlocked position
4. Indicator, left backrest lock,
not visible in locked position



Split Folding Rear Seat Backrest

On vehicles with optional split folding rear seat backrest you can fold down the two sections
separately to enlarge the cargo area.

Fold down:
Pull locking handle and fold backrest forward.
Set up:
Pull backrest up until it locks in its upright position. Check for secure locking by pushing and pulling on the backrest.

Warning !
Always lock backrest in its upright position when rear seat bench is occupied by passengers, cargo is being
carried in the trunk, or the extended cargo area is not in use.


Note:
To prevent unauthorized persons from access to the trunk, always lock backrest in its upright position.

Loading instructions
(Vehicles with enlarged cargo area)

The total load weight including vehicle occupants and luggage/ cargo should not exceed the vehicle capacity
weight indicated on the certification tag which can be found on the left door pillar. The handling characteristics
of a fully loaded vehicle depend greatly on the load distribution. It is therefore recommended to load the vehicle
according to the illustrations shown, with the heaviest items being placed towards the front of the vehicle.
Always place items being carried against front or rear seat backrests, and fasten them as securely as possible.
The heaviest portion of the cargo should always be kept as low as possible since it influences the handling
characteristics of the vehicle.

Notes:
The trunk is the preferred place to carry objects. The enlarged cargo area should only be used for items which
do not fit in the trunk alone.

Warning !
In an accident, during hard braking or sudden maneuvers, loose items will be thrown around inside the
vehicle, and can cause injury to vehicle occupants unless the items are securely fastened in the vehicle.
To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things.
Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs.
Do not place anything on the shelf below the rear window. Never drive vehicle with trunk lid open while
pass-through is not closed and seat backrest sections not locked in its upright position. Deadly carbon
monoxide (CO) gases may enter vehicle interior resulting in unconsciousness and death.

Steering Lock

0 - The electronic key can be withdrawn in this position only. The steering is locked with the electronic key removed
from the steering lock. The electronic key an be removed only with the selector lever in position "P" and the foot off
the brake pedal. After removing the electronic key or with the electronic key in steering lock position 0, the
selector lever is locked in position "P".
1 - Steering is unlocked. (If necessary, move steering wheel slightly to allow the electronic key to be turned clockwise
to position 1.) Most electrical consumers can be operated. For detailed information see respective subjects.
2 - Driving position.
3 - Starting position.

Refer to Index for Starting and turning off the engine.


Warning !
When leaving the vehicle always remove the electronic key from the steering lock, and lock the vehicle.
Do not leave children unattended in the vehicle, or with access to an unlocked vehicle.
Unsupervised use of vehicle equipment may cause serious personal injury.


Important !
If the electronic key is left in the steering lock position 0 for an extended period of time, it can no longer be turned
in the lock. In this case, remove electronic key from steering lock and reinsert.

Notes:
A warning sounds when the driver's door is opened with the electronic key in steering lock position 1 or 0. With the
engine at idle speed, the charging rate of the alternator (output) is limited. It is therefore recommended to turn off
unnecessary electrical consumers while driving in stop-and-go traffic. This precaution helps to avoid draining of the
battery. Unnecessary strain on the battery and charging system may be minimized by turning off the following power
consumers, for example: Heated seats, rear window defroster. In addition, the automatic climate air volume control
should be set to the lowest position. The steering lock can only be unlocked with the vehicle battery properly
connected.

Caution !
To prevent accelerated battery discharge and a possible dead battery, always remove the electronic key from the
steering lock. Do not leave the electronic key in steering lock position 0.

Engine Oil Consumption
Engine oil consumption checks should only be made after the break-in period. During the breaking period, higher oil
consumption may be noticed and is normal. Frequent driving at high engine speeds results in increased consumption.


Fuel Reserve and Fuel Cap Placement Warning Lamp
With the electronic key in steering lock position 2, the fuel reserve warning lamp comes on. It should go out
immediately when the engine is running.
If the warning lamp does not go out after starting the engine, or if it comes on while driving, it indicates that the fuel
level is down to the reserve quantity of approximately 2.1 gal (8 liters).
The warning lamp blinks when the fuel c ap is not closed, or a fuel system leak has been detected. Retighten cap and
see if lamp goes out.
If the warning lamp continues to blink after closing the fuel cap correctly, hav e the fuel system checked at your
authorized Mercedes-Benz dealer as soon as possible.
Leaving the engine running and the fuel cap open can cause the "Check Engine" lamp to illuminate).


Tachometer
Red marking on tachometer: Excessive engine speed. Avoid th is engine speed, as it may result in serious engine
damage that is not covered by the Mercedes-Benz Limited Warranty. For engine protection, the fuel supply is
interrupted if the engine is operated within the red marking.


Seat Belt Warning Lamp
With the electronic key in steering lock position 2, the warning lamp comes on, and a warning sounds for a short time
if the drivers seat belt is not fastened. After starting the engine, the warning lamp blinks for a brief period to remind
the driver and passengers to fasten seat belts.

Trunk Lamp
If the trunk is to remain open for a long period of time, the trunk lamp can be switched off by pulling out the plunger
in the switch (arrow). This prevents the vehicle battery from being discharged. When the trunk lid is closed, the switch
will reset and turn on the lamp next time the lid is opened.


Stowing Things in the Vehicle

Warning !
To help avoid personal injury during a collision or sudden maneuver, exercise care when stowing things.
Put luggage or cargo in the trunk if possible. Do not pile luggage or cargo higher than the seat backs.
Do not place anything on the shelf below the rear window.

Exterior Lamps
Headlamp Adjustment

Correct headlamp adjustment is extremely important. Check and readjust headlamps at regular intervals and
when a bulb has been replaced.




Headlamp Assembly
1. Cover for low beam headlamp bulb, fog lamp, and level for vertical adjustment
2. Latch for cover (1)
3. Cover for high beam headlamp bulb
4. Clamp for cover (3)
5. Headlamp vertical adjustment screw

6. Headlamp horizontal adjustment screw
7. Scale for horizontal adjustment
8. Electrical connector for low beam headlamp bulb
9. Electrical connector for fog lamp bulb
10.Electrical connector for high beam headlamp bulb



Replacing Bulb:
To prevent a possible electrical short circuit, switch off lamp prior to replacing a bulb. When replacing bulbs,
install only 12 volt bulbs with the specified watt rating. When replacing halogen bulbs do not touch glass
portion of bulb with bare hands. Use plain paper or a clean cloth.

Warning !
Halogen lamps contain pressurized gas. A bulb can explode if you:
• touch or move it when hot,
• drop the bulb,
• scratch the bulb.
Wear eye and hand protection.

Bulb for Low Beam H7 (55 W) Bulb for Fog Lamp H1 (55 W)

Open hood.
Depress latch (2) and remove cover (1). Pull of electrical connector (8) or (9). Unhook clamping ring and
removes bulb. Insert new bulb (seating properly in cutouts of bulb socket), and mount clamping ring.
Reinstall and push electrical connector on securely. Reinstall bottom end of cover (1) and push against top
end of cover until properly seated. Check lamp for proper operation.

Xenon (optional)
Bulb for Low Beam

Warning !
Because of high voltage in Xenon lamps, it is dangerous to replace the bulb or repair the lamp and its
components. We recommend that you have such work done by a qualified technician.

Bulb for High Beam H1 (55 W)

Open hood.
Move retaining clamps (4) aside and remove cover (3). Pull off electrical connector (10). Unhook clamping ring
and pull out bulb together with clamping ring. Remove bulb. Insert new bulb (seating properly in cutouts of bulb
socket), mount clamping ring. Reinstall and push electrical connector on securely. Reinstall cover and fasten
with retaining clamp (4).

Turn Signal, Parking, Side Marker and Standing Lamp
(2357 NA [28.5/8.3 W/30/2.2 cp bulb])

Open hood.
Squeeze latch (1) together and lift complete lamp assembly out to front of vehicle. Twist bulb socket (2)
counterclockwise and pull out. Push bulb into socket, turn counterclockwise and remove. Insert new bulb in socket
push in and twist clockwise. Reinstall bulb socket. Reinstall lamp assembly by sliding tabs (3) into guides (4) until
properly seated.

1. Latch for turn signal, parking, side marker, and standing lamp assembly
2. Bulb socket for turn signal, parking, side marker, and standing lamp
3. Tab
4.Guide