SA0R1±03
± SUSPENSION AND AXLETROUBLESHOOTING
SA±1
2001 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
TROUBLESHOOTING
PROBLEM SYMPTOMS TABLE
Use the table below to help you find the cause of the problem. The numbers indicate the priority of the likely
cause of the problem. Check each part in order. If necessary, replace these parts.
SymptomSuspect AreaSee page
Wander/pulls
5. Tires (Worn or improperly inflated)
6. Wheel alignment (Incorrect)
7. Steering linkage (Loosen or worn)
8. Hub bearings (Loosen or worn)
9. Steering gear (Out of adjustment or broken)
10.Suspension parts (Worn out)SA±2
SA±4
SA±7
±
SA±9
SA±43
±
±
Bottoming
1. Vehicle (Overloaded)
2. Spring (Weak)
3. Shock absorber (Worn out)±
SA±17
SA±86
SA±21
SA±89
Sways/pitches
1. Tires (Worn or improperly inflated)
2. Stabilizer bar (Bent or broken)
3. Shock absorber (Worn out)SA±2
SA±39
SA±105
SA±21
SA±89
Front wheel shimmy
1. Tires (Worn or improperly inflated)
2. Wheels (Out of balance)
3. Shock absorber (Worn out)
4. Wheel alignment (Incorrect)
5. Ball joints (Worn)
6. Hub bearings (Loosen or worn)
7. Steering linkage (Loosen or worn)
8. Steering gear (Out of adjustment or broken)SA±2
SA±2
SA±21
SA±4
SA±34
SA±9
±
±
Abnormal tire wear
1. Tires (Improperly inflated)
2. Wheel alignment (Incorrect)
3. Suspension parts (Worn out)
4. Shock absorber (Worn out)SA±2
SA±4
SA±7
±
SA±21
SA±89
Noise in rear differential
1. Oil level (Low or wrong grade)
2. Excessive backlash between pinion and ring gear
3. Ring, pinion or side gears (Worn or chipped)
4. Pinion shaft bearing (Worn)
5. Side bearing (Worn)SA±61
SA±63
SA±63
SA±63
SA±63
Oil leak from rear differential
1. Oil level (Too high or wrong grade)
2. Drive pinion oil seal (Worn or damaged)
3. Side gear oil seal (Worn or damaged)
4. Companion flange (Loose or damaged)
5. Side gear shaft (Damaged)SA±61
SA±63
SA±60
SA±67
SA±63
R07928
F04238
16 inch wheel
17 inch wheelApprox. 25 mm (0.984 in.)
Approx. 25 mm (0.984 in.)
R11097
± SUSPENSION AND AXLETIRE AND WHEEL
SA±3
2003 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
3. INSPECT WHEEL BALANCE
(a) Check and adjust the off±the±car balance.
(b) If necessary, check and adjust the on±the±car balance.
Unbalance after adjustment: 8.0 g (0.018 lb) or less
NOTICE:
Adhere the sticking type balance weight to the flat
position shown in the illustration.
Push the balance weight securely with a finger to ad-
here it to the position.
(Pushing force: 10 kgf/more than 2 secs.)
After cleaning the surface which the balance weight
will be adhered to of dirt, oil and water with a cleaning
detergent, adhere the balance weight to the surface.
Do not touch the sticking surface of the tape.
Do not use the once used balance weight.
Please use the TOYOTA genuine sticking type bal-
ance weight.
4. CHECK WHEEL BEARING LOOSENESS
(a) Check the backlash in the bearing shaft direction.
Maximum: 0.05 mm (0.0020 in.)
(b) Check the axle hub deviation.
Maximum: 0.05 mm (0.0020 in.)
5. CHECK FRONT SUSPENSION FOR LOOSENESS
6. CHECK STEERING LINKAGE FOR LOOSENESS
7. CHECK BALL JOINT FOR LOOSENESS AND
EXCESSIVE PLAY (See page SA±34)
8. CHECK SHOCK ABSORBER WORKS PROPERLY
Check for oil leak
Check mounting bushings for wear
Bounce front and rear of the vehicle
