2000 LEXUS GS400 length

R06400
Brass Bar
W00123
W04397
F02586
SSTFulcrum
Length
SR±56
± STEERINGPOWER STEERING GEAR
2226 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(c) Using a brass bar and hammer, stake the washer.
NOTICE:
Avoid any impact to the rack.
14. INSTALL RH AND LH RACK BOOTS, CLAMPS AND
CLIPS
(a) Ensure that the tube hole is not clogged with grease.
HINT:
If the tube hole is clogged, the pressure inside the boot will
change after it is assembled and the steering wheel is turned.
(b) Install the boot.
NOTICE:
Be careful not to damage or twist the boot.
(c) Using pliers tighten a new clamp, as shown in the illustra-
tion.
15. INSTALL RH AND LH TIE ROD ENDS AND LOCK NUTS
(a) Screw the lock nut and tie rod end onto the rack end until
the matchmarks are aligned.
(b) After adjusting toe±in, torque the nut.
(See page SA±4)
Torque: 55 N´m (560 kgf´cm, 41 ft´lbf)
16. INSTALL 2 TURN PRESSURE TUBES
(a) Install a new union seat to the rack housing.
(b) Using SST, install the tube.
SST 09633±00020
Torque: 20 N´m (203 kgf´cm, 15 ft´lbf)
HINT:

Use a torque wrench with a fulcrum length of 300 mm
(11.81 in.).

This torque value is effective in case that SST is parallel
to a torque wrench.

F02400
SA1204
± SUSPENSION AND AXLEFRONT WHEEL ALIGNMENT
SA±5
2005 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
5. ADJUST CAMBER
HINT:

After adjusting the camber, inspect the caster and toe±in.

Try adjusting the camber to the center value of the specifi-
cation.
(a) Loosen the camber adjusting cam nut of the lower sus-
pension arm.
(b) Turn the camber adjusting cam of the lower suspension
arm and adjust camber.
HINT:
Camber changes about 5' (0.08°) with each graduation of the
adjusting cam.
(c) Torque the camber adjusting cam nut of lower suspension
arm.
Torque: 172 N´m (1,755 kgf´cm, 127 ft´lbf)
6. ADJUST TOE±IN
(a) Remove the boot clips.
(b) Loosen the tie rod end lock nuts.
(c) Turn the left and right rack ends an equal amount to adjust
the toe±in.
HINT:

Try to adjust the toe±in to the center value.

Make sure that the lengths of the left and right rack ends
are same.
Rack end length difference: 1.5 mm (0.059 in.) or less
(d) Torque the tie rod end lock nuts.
Torque: 56 N´m (570 kgf´cm, 41 ft´lbf)
(e) Place the boot on the seat and clamp it.
HINT:
Make sure that the boots are not twisted.

R06938
SSTClearance
R08199
R07026
SA±58
± SUSPENSION AND AXLEREAR DRIVE SHAFT
2058 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
(d) Using SST, adjust the clearance of the clamp.
SST 09240±00020 (09242±00080)
Clearance: 0.8 mm (0.031 in.) or less
(e) The drive shaft is designed to move ±20 mm (0.79 in.)
from the normal position.
Drive shaft standard length:
RH598.5 mm (23.563 in.)
LH553.5 mm (21.791 in.)
8. INSTALL NEW END COVER
(a) Pack grease into the end cover.
Grease capacity50 ± 55 g (1.8 ±1.9 oz.)
(b) Remove grease from the surface of the inboard joint fac-
ing to the cover.
(c) Glue on a new gasket, with the glued side facing toward
the outer race side of the inboard joint.
(d) Align the bolt holes of the cover with those of the inboard
joint.
(e) Install the 6 hexagon bolts and washers from the end cov-
er side.
(f) Install the 6 nuts to the boot side.
(g) Using a 10 mm hexagon wrench, tighten the bolts. Do this
in the order shown, and repeat several times.
(h) Check that the claw of the end cover touches the inboard
joint.
9. CHECK DRIVE SHAFT (See page SA±54)

SA0R4±01
SA3213
D AB
C Front
F03479
A
B
F02401
± SUSPENSION AND AXLEREAR WHEEL ALIGNMENT
SA±7
2007 Author: Date:
2000 LEXUS GS300/GS400 (RM718U)
REAR WHEEL ALIGNMENT
INSPECTION
1. MEASURE VEHICLE HEIGHT (See page SA±4)
2. INSTALL CAMBER±CASTER±KINGPIN GAUGE
ONTO WHEEL ALIGNMENT TESTER
Follow the specific instructions of the equipment manufacturer.
3. INSPECT CAMBER
Camber
Left±right error±0°47' ± 30' (±0.78° ± 0.5°)
30' (0.5°) or less
4. INSPECT TOE±IN
Toe±in
(total)A + B: 0°08' ± 12' (0.13° ± 0.2°)
C ± D: 1.4 ± 2 mm (0.056 ± 0.08 in.)
5. ADJUST CAMBER AND TOE±IN
(a) Measure the lengths of the toe control link and No.2 lower
suspension arm, as shown in the illustration.
Length: A ± B = 4.0 mm (0.16 in.) or less
If they are not within the specifications, adjust the lengths of
them by turning the adjusting cam, as shown, until (A ± B) is less
than 4.0 mm (0.16 in.).
(b) Measure the camber and toe±in.
(c) Adjust the camber.
(1) Loosen the camber adjusting cam nut of lower sus-
pension arm No.2.
(2) Turn the camber adjusting cam of lower suspension
arm No.2 and adjust camber.
HINT:
Camber changes about 5.0' (0.08°) with each graduation of the
cam.
(3) Torque the camber adjusting cam nut.
Torque: 110 N´m (1,120 kgf´cm, 81 ft´lbf)