2000 Lexus ES300 lock

STARTING AND DRIVING
277
IGNITION SWITCH WITHSTEERING LOCK
31E069

STARTING AND DRIVING
278ªSTARTº ± Starter motor on. The key will return to
the ªONº position when released.
For starting tips, see page 281.
ªONº ± Engine on and all accessories on.
This is the normal driving position.
NOTICE
Do not leave the key in the ªONº position if the
engine is not running. The battery will dischargeand the electronic ignition system/distributorignition system could be damaged.
ªACCº ± Accessories such as the radio operate, but
the engine is off.
If you leave the key in the ªACCº or ªLOCKº position and
open the driver's door, a buzzer will remind you to
remove the key.

STARTING AND DRIVING
279
31E070
ªLOCKº ± Engine is off and the steering wheel is
locked. The ignition key can be removed only at this
position.
You must push in the key to turn it from ªACCº to the
ªLOCKº position. The selector lever must be put in the
ªPº position before turning the key to the ªLOCKº
position.
Once you remove the key, the engine immobiliser
system is automatically set. See ªEngine immobiliser
systemº on page 12.
When starting the engine, the key may seem stuck at the
ªLOCKº position. To free it, first be sure the key is
pushed all the way in, and then rock the steering wheel
slightly while turning the key gently.
If, in an emergency, you must turn the engine off while
the vehicle is moving, turn the key only to ªACCº.

With the brake pedal depressed, shift
while holding the lock release button
in. (The ignition switch must be in the
ªONº position.)
Shift while holding the lock release
button in.
Shift normally.
STARTING AND DRIVING
282
AUTOMATIC TRANSMISSION
Your automatic transmission has a shift lock system
to minimize the possibility of incorrect operation.
This means you can only shift out of ªPº position
when the b rake pedal is depressed (with the ignition
switch in ªONº position and the lock release button
depressed). ( )
31E005a
1
Lock release button

STARTING AND DRIVING
294
NOTICE
If you rock your vehicle, observe the followingprecautions to prevent damage to thetransmission and other parts.
Do not depress the accelerator pedal whileshifting the selector lever or before thetransmission is completely shifted to forwardor reverse gear.
Do not race the engine and avoid spinning thewheels.
If your vehicle remains stuck after rocking thevehicle several times, consider other wayssuch as towing.
(i) If you cannot shift the selector lever out of ªPº position
If you cannot shift the selector lever from ªPº position
even though the brake pedal is depressed, use the shift
lock override button. For instructions, see ªIf you cannot
shift automatic transmission selector leverº on page
369.

STARTING AND DRIVING
302
VEHICLE SKID CONTROLSYSTEM
The vehicle skid control system helps provide
comprehensive control of the systems such as an
anti±lock brake system, brake assist system,
traction control, engine control, etc. This system
automatically controls the output of the brakes or
engine to help prevent the vehicle from skidding
when cornering on a slippery road surface or abrupt
steering wheel operation occurs.
31E013±1

Slip indicator light
If the vehicle is going to skid during driving, the slip
indicator light flashes and an alarm sounds
intermittently.
The vehicle skid control activates when the vehicle
speed is about more than 15 km/h (9 mph). You may hear a sound in the engine compartment for a
few seconds when the engine is started or just after the
vehicle is started. This means that the vehicle skid
control is in the self±check mode and does not indicate
a malfunction.

STARTING AND DRIVING
307
CAUTION
Do not pump the brake pedal if the engine stalls.
Each push on the pedal uses up your reserved
vacuum.
 Even if the power assist is completely lost, the brakes
will still work. But you will have to push the pedal
hard, much harder than normal. And your braking
distance will be longer.
Anti±lock brake system
The anti±lock brake system is designed to help
prevent lock±up of the wheels during a sudden
braking or braking on slippery road surfaces. This
assists in providing stability and steering
performance of the vehicle under these
circumstances.
Effective way to press the ABS brake pedal: When the
anti±lock brake system function is in action, just hold the
brake pedal down more firmly. Especially, in a panic stop,
you need to keep it depressed more firmly, and do not pump
the brake. Pumping the brake pedal makes the stopping
distance longer.

STARTING AND DRIVING
308The anti±lock brake system becomes operative after the
vehicle has accelerated to a speed in excess of
approximately 10 km/h (6 mph). It stops operating when
the vehicle decelerates to a speed below approximately
5 km/h (3 mph).
Depressing the brake pedal on slippery road surfaces
such as on the manhole cover, the steel plate under the
construction, joints in the bridge, etc. on a rainy day
tends to activate the anti±lock brake system.
You may hear a click or motor sound in the engine
compartment for a few seconds when the engine is
started or just after the vehicle is started. This means
that the anti±lock brake system is in the self±check
mode, and does not indicate a malfunction.
When the anti±lock brake system is activated, the
following conditions may occur, however, do not
indicate a malfunction of the system:

You may hear the anti±lock brake system operating
and feel the brake pedal pulsating and the vibrations
of the vehicle body and steering wheel. You may also
hear the motor sound in the engine compartment
even after the vehicle is stopped.
 At the end of the anti±lock brake system activation,
the brake pedal may move a little to the forward.