2000 HONDA PRELUDE light

Ai
r Conditionin g System , Ai r Conditionin g Filte r

Periodically check the engine's
radiator and air conditioning condenser for leaves, insects, and
dirt stuck to the front surface. These
block the air flow and reduce cooling efficiency. Use a light spray from a
hose or a soft brush to remove them.
The. condenser and radiator fins bend
easily. Only use a low-pressure spray
or soft-bristle brush to clean them.
Run the air conditioning at least once
a week during the cold weather
months. Run it for at least ten
minutes while you are driving at a steady speed with the engine at
normal operating temperature. This
circulates the lubricating oil con-
tained in the refrigerant. If the air conditioning does not get as
cold as before, have your dealer
check the system. Recharge the

system with Refrigerant HFC-134a

(R-134a). (See Specifications on page
265.)

Whenever you have the air conditioning

system serviced, make sure the service

facility uses a refrigerant recycling
system. This system captures the
refrigerant for reuse. Releasing
refrigerant into the atmosphere can

damage the environment.
Ai
r Conditionin g Filte r
The air conditioning filter removes pollen and dust from the outside air
the climate control system brings
into the interior.
This filter should be replaced every 30,000 miles (48,000 km) under
normal conditions. It should be
replaced every 15,000 miles (24,000
km) if you drive primarily in urban areas that have high concentrations
of soot in the air from industry and
diesel-powered vehicles. Replace it
more often if air flow from the
heating and cooling system becomes
less than usual. Have the air conditioning filter replaced by your
Honda dealer.

Maintenance

NOTIC
E NOTIC
E

Light
s

Check the operation of your car's
exterior lights at least once a month.
A burned out bulb can create an unsafe condition by reducing your
car's visibility and the ability tosignal your intentions to other
drivers.
CONTINUED

Maintenanc e

PARKIN
G LIGH T
HEADLIGHT LO W BEA M
SID E MARKE R LIGH T
HEADLIGH
T HIG H BEA M
TUR N SIGNA L

Light
s

Check the following:
Headlights (low and high beam)
Parking lights
Taillights Brake lights
High-mount brake light
Turn signals Back-up lights
Hazard light function
License plate light
Side marker lights
Daytime running lights
(Canadian models)

If you find any bulbs are burned out,
replace them as soon as possible. Refer to the chart on page 265 to
determine what type of replacement
bulb is needed. TAILLIGHT/BRAK
E LIGH T
HIGH-MOUN
T BRAK E LIGH T

TAILLIGH T
BACK-U P LIGH T
SID E MARKE R LIGH T
TURN SIGNA L

LICENSE PLAT E LIGH T

Maintenanc e

Light
s
Headligh t Aimin g
The headlights were properly aimed when your car was new. You shouldcheck their aim if you regularly carry
heavy items in the trunk or pull a trailer. Each headlight assembly has
horizontal and vertical adjustment
indicators. These are set to their "0"
positions after the headlights are
aimed at the factory.
To check these settings:
1. Make sure the fuel tank is full. Park the vehicle on level ground.
2. The driver or someone who weighs the same should he sittingin the driver's seat for all checks
and adjustments.
Load the trunk with the items you
normally carry. HORIZONTA
L ANGL E GAUG E
If you usually pull a trailer, load it as
you would normally and attach it to
the car. Push down on the front and
rear bumpers several times to make sure the car is sitting normally.
3. Open the hood.
4. Check the horizontal angle gauge. The line on the adjustment screwindicator should line up with the
"0" mark on the gauge. VERTICA
L ANGL E GAUG E
5. Check the vertical angle gauge. The bubble should be centeredunderneath the longest scribe
mark on the gauge.
MaintenanceCONTINUED
BUBBLE

Light
s

HORIZONTA L ADJUSTMEN T

6. If either indicator is not aligned with its "0" mark as described, anadjustment can be made using a
Phillips-head screwdriver to
realign it with the "0" mark. Please
refer to the illustrations.
VERTICA
L ADJUSTMEN T

7. If you cannot get an indicator to align, have your Honda dealer
inspect the vehicle for body

damage or suspension problems.
Replacin
g a Headligh t Bul b

Your car has two bulbs on each side, four in total. Make sure you are
replacing the bulb that is burned out.
Your car uses halogen headlight bulbs. When replacing a bulb, handleit by its plastic case and protect the
glass from contact with your skin or
hard objects. If you touch the glass,clean it with denatured alcohol and a
clean cloth.
The headlight bulbs in your car are H1 headlight bulbs for longer life.
We recommend the use of Genuine Honda parts for replacing a
headlight bulb.

Halogen headlight bulbs get very hot

when lit. Oil, perspiration, or a scratch

on the glass can cause the bulb to

overheat and shatter.

Maintenanc e
NOTIC
E

Light
s

1. Open the hood.
2. Remove the electrical connector from the bulb by squeezing theconnector on both sides to unlock
the tab. Pull the connector straight off.
3. Remove the rubber weather sealby pulling on the tab.
4. Unclip the end of the hold-down wire from its slot. Pivot it out ofthe way and remove the bulb. 5. Insert the new bulb into the hole,
making sure the tabs are in theirslots. Pivot the hold-down wire
back in place and clip the end into
the slot.
6. Install the rubber seal over the back of the headlight assembly.Make sure it is right side up; it is
marked "TOP."
7. Push the electrical connector onto the tabs of the new bulb. Makesure it locks in place.
Turn on the headlights to test the new bulb.

Maintenance

BUL
B
HOLD -
DOW N
WIR E
WEATHE R SEA L
CONNECTO R

Light
s
Replacin g a Parkin g Ligh t Bul b
1. Open the hood. The front parking light is next to the headlight bulb.

If you need to change a bulb on

the passenger's side, remove the

radiator reserve tank by pulling it out of its holder.
2. Remove the socket from theheadlight assembly by turning itone-quarter turn counterclockwise. 3. Pull the bulb straight out of its
socket.
Push the new bulb straight into
the socket until it bottoms.
4. Insert the socket back into the headlight assembly. Turn itclockwise to lock it in place.

5. Turn on the parking lights to
make sure the new bulb works.

6. (Passenger's side)
Reinstall the radiator reserve tank.

Maintenanc e

Light
s

Replacin g a Fron t Sid e Marke r
Ligh t Bul b
1. Use a Phillips-head screwdriver to remove the side marker assembly's
mounting screw.
2. Remove the side marker assembly from the bumper. 3. Remove the socket from the side
marker assembly by turning it one-quarter turn counterclockwise.
4. Pull the bulb straight out of its socket.
Push the new bulb straight into
the socket until it bottoms. 5. Insert the socket back into the
side marker assembly. Turn it
clockwise to lock it in place.
6. Test the side marker to make sure the new bulb is working.
7. Put the side marker assembly into the bumper. Make sure the tab on
the side marker assembly fits into
the bumper slot. Tighten themounting screw.
Maintenance

SCRE
W
BUL
B

SOCKE T

FRON T SID E MARKE R ASSEMBL Y