Page 1348 of 1395
)
)
SRS MAIN HARNESS18P CONNECTOR
From page 24 50
Check for an opon in the cabl€ re€l (cont'd):
5. Reconnect the batterv positive cable, then reconnect thenegative cable,6. Erase the DTC memory (see page 24-28).7. Read the DTC (see page 24-2d.
ls DTC 1-1 or DTC 1-2 indic.ted?
YESNO
Open or increased resistance in the cable reel; replacethe cable reel (see paqe 24-91J.
Check for an open in the SRS main harne$:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait lor three minutes.2- Disconnect the front passenger's airbag connector landdisconnect both seat belt tensioner connectors),3, Disconnect the SRS main harness 18P connector fromthe SRS unit. Do not disconnect the special tool 12 O)from the SRS main harness.4. Check resistance between terminals No. 1 and No. 13 ofthe SRS main harness 18P connector.There should be aoorox.2.0 3.0 0.
ls the rcsistanc€ as soecified?
NOYES
Poor contact at the SRS main harnoss 18P conn€ctor;check the connector.. It the connecior is OK, substitute a lnown-good SRSunit, and recheck..lf the problem is still present, .eplace the SRS mainharness,
Opon or inc.oased rc3istance in the SRS main harnoss;roDlace tho ha]nss.3.
24-51
www.emanualpro.com
Page 1350 of 1395
From page 24-52
Chock for a shon in th6 cablo recl {cont'dl:5. Reconnect the battery oositive cable, then reconnect thanegative cable.6. Ersse the DTC memory (see page 24-28).7. Read the DTC (see page 24-26l'.
ls DTC 'l-3 indic{tod?
NOYES
Short in the csble reel; replace tha cabls rcol lsao paga
24-911.
Chock for a short in th€ SRS main ha.nors:1. Disconnect the battery negative cable, th€n disconnectthe Dositive cable, and wait for three minutes.2. Disconn€ct tho lront passengor's airbag connector (and
disconnect both seat belt tensioner connectors).3. Disconnect the SRS main harness 18P connector fromthe SRS {rnit. Do not disconnect the special tool (2 0)from the SRS main harness 2P connector.4. Check the resistance between terminals No. 1 and No. 13of SRS main harness 18P connector.There should be aDorox. 2.0 - 3.0 0.
b th€ rsciitlnce a3 sDecifi6d?
NOYES
Faulty SRS unit; rspl.c. th6 SRS unit l.co p.sc 2a-95,,
Shori in the SRS m.in h.rn.e!; ropbce the SRS main htr-ne33.
SRS UNIT
)SRS MAIN HABNESS18P CONNECTOR
c806
)
(., Lzl 3 ll63
1518
Wire side ottormrnats
24-53
www.emanualpro.com
Page 1352 of 1395
Ftom page24-54
Check for 6 short power in the cable r6el {cont'd):5. Reconnect the battery positive cable, then reconnect thenegative cable.6. Erase the DTC memory (see page 24-28).7. Read the DTC (see page 24-261.
b DTC 1-4 indicarodz
YESNO
Short to power in lhe cablo roel; replace th€ cabl€ ieel{see pago 24-91).
Check tor a short to power in th. SRS main harn$s:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnect the front passenger's airbag connector {anddisconnect both seat belt tensioner connectors).3. Rernove the special tool (2 O) from the SRS main harness2P connector.4. Disconnect the SRS main harness 18P connector fromthe SRS unit.5. Beconnect the batterv positive cable, then reconnect thenegative cable.6. Connect a voltmeter between the No. 1 {+) terminal olthe SRS main harness 18P connector and body ground.7. Turn the ignition switch ON (ll), and measure voltage.There should be 0.5 V or less.8. Turn the ignition switch OFF.9. Connect a voitmeter between the No. 13 {+i terminal ofthe SRS main harness 18P connector and body ground.10.Turn the ignition switch ON lll), and measure voltage.There should be 0.5 V or less.
Are voltages as specified?
YESNO
Faulty SRS unit; replaco th€ SRS unit lsoo pas6 24-95).
Short to power in th€ SRS main hamoss; roplece the SRSmain haanass.
SRS MAIN HARNESS18P CONNECTOR
24-55
www.emanualpro.com
Page 1354 of 1395
)
SRS MAIN HARNESS18P CONNECTOR
)
From page 24 56
Check{or a short to ground in the cable reel (cont'd):
5. Reconnect the batterv positive cable, then reconnect thenegative cable.6. Erase lhe DTC memoty lsee page 24-28).7. Read the DTC lsee page 24 26).
ls OTC 1-5 indicated?
YESNO
Short lo ground in the cable reel; replace the cable reel{see oaoe 2,1-91}.
Check for a short to ground in the SRS main harness:'1. Disconnect the battery negative cable, the disconnect thepositive cable, and wait for three minutes.2. Disconnect the tront passenger's airbag 2P connector(6nd disconnect both seat belt tensioner connectors).3. Remove the special tool 12 {))from the SRS main harness2P connector.4- Disconnect the SRS main harness 18P connector fromthe sRs unit.5. Check resistance between the No. l terminal o{theSRSmain harness 18P connector and ground, and betweenthe No. 13 terminal of the SRS main harness 18P connec-tor and ground.There should be I M0 or more.
ls lhe resistance as soecitiod?
NOYES
Faulw SRS unit reDlace the SRS unit lsee paqe 24-951.
Short to ground in the SRS main harness; replace the SRSmain ham€ss,
24-57
www.emanualpro.com
Page 1356 of 1395
)
From page 24 58
Check fo. an oD6n in the SRS main harness:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnectthe driver's airbag 2P connector land disconnectboth seat belt tensioner connectors) (see page 24 23).3. Disconnect the SRS main harness 18P connector fromthe SRS unit. Do not disconnect the soecial tool (2 Oifrom the SRS main harness.4. Check resistance between the No. 10 terminal and No. 14terminal of the SRS main harness 18P connector. Thereshould be aoorox. 2.0 - 3.0 g.
ls the .osistanc€ as soecified?
NOYES
Poor contacl ai the SRS main harness 18P connecloricheck lhe connector,.lf the conneclor is OK, substitute a known-good SRSunit, and recheck..lf the problem is still present, replace the SRS mainhatnesli,
Open or increased resistance in the SRS main harness;replace the harness.
UNITsRs
18P CONNECTOR
24-59
www.emanualpro.com
Page 1358 of 1395
)
SRS MAIN HARNESS18P CONNECTOR
)
)
From page 24 60
Ch6ck tor a short to another wire or decreasod aGsistance inlh€ SRS main harness:1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.2. Disconnect the driver's airbag 2P connector (and disconnectboth seat belt tensioner connectors).3. Disconnect the SRS main harness '18P connector fromthe SRS unit. Do not disconnect the special tool (2 O).4. Check resistance between the No. 10 terminal and No. 14terminal of the SRS main harness 18P connector. Thereshould be aoorox. 2.0 - 3.0 0.
ls the rosistanc6 as specified?
YESNO
Faultv SRS unit; replace lhe SRS unit lsee page 24-95).
Short to anothor wire or decre.sed re3i3t.nce in the SRSmain harness; replac€ the SRS main harn*s.
24-61
www.emanualpro.com
Page 1360 of 1395
Frcm page24-62
Check lor a short to power in the SRS main harness:
1. Disconnect the battery negative cable, then disconnectthe positive cable, and wait for three minutes.
2. Disconnect the drive/s airbag 2P connector (and disconnect
both seat belttensionerconnectors).3. Disconnect the SRS main harness 18P connector trom
the SRS unit.4. Remove the specialtool (2 0) from the SRS main harness
2P connector,5. Reconnect the batterv positive cable, then reconnect the
negative cable.6. Connect a voltmeter between the No. 10 (+) terminal of
SRS main harness 18P connector and ground.
7. Turn the ignition switch ON (ll). and measure voltage
There should be 0.5 V or less.8. Connect a voltmeter between the No. 141+) terminal of
the SRS main harness 18P connector and ground, and
measure voltage. There should be 0.5 V or less.
Are voltages .3 specifiedT
YESNO
Faulty SRS unit; replace the SRS unit (sce page 24'95).
Short to powor in the SRS main ha.ne3s; replace the SRS
main hdrness.
sRs.I8P CONNECTOR
24-63
www.emanualpro.com
Page 1362 of 1395
)J
From page 24'64
Check for a short to ground in the SRS main harnessl1. Disconnect the battery negative cable, then disconnectthe posilive cable. and wait for three minutes.2. Disconnect the driver's airbag 2P connector (and discon-nect both seat belt tensioner connectors),3. Disconnect the SBS main harness 18P connector fromthe sRs unit.4. Remove the special tool (2 O) from the SRS main harness2P connector,5. Check resistance between the No. 10 terminal of the SRSmain harness 18P connector and ground, and betweenthe No. 14 terminal of the SRS main harness 18P connector and ground. There should be 1 M0 or more.
ls the resistance as sD€citied?
NOYES
Faultv SRS uniu replace the SRS unit {see paqe 24-951.
Short to ground in the SRS main harn€ss; replac€ ihe SRSmain harness.
sRs18P CONNECTOF
24-65
www.emanualpro.com
