Page 5 of 16
²SVT-signature white-faced gauges
²Standard power 10±way driver's seat with unique perforated leather
²Accentuated seat back and bottom lateral bolstering
²Additional rear seat bottom bolstering
²Standard leather: seating surfaces, steering wheel, shifter knob, shifter
boot, parking brake boot
²Unique texture door trim inserts
²SVT logo floormats, color-keyed
000123
000010 20 304050607080
90
120
140
150130
160
MPH
20 406080100140
120
16 0
18 0
200
220
240
260
110 10 0
EF
PREMIUM FUEL ONLY
12
03
x 1000
4
5
6
7
8
NORMAL
BRAKE
O/D
OFFTRACTION
CONTROLCHECK
ENGINE
SVT Contour specific features
5
Page 7 of 16
ENGINE/TRANSMISSION
²Horsepower Ð 200 hp @ 6 600 rpm
²Torque Ð 167 lb/ft at 5 500 rpm
²Redline Ð 6 750 rpm (fuel shut-off 7 000 rpm)
²Compression ratio Ð 10.0:1
²Throttle body Ð 60 mm
²Mass air sensor Ð 70 mm
²Air filter assembly Ð large capacity, conical
²Upper intake manifold and cylinder heads Ð Extrude Honeypolished
²Lower intake manifold Ð 32 mm
²Pistons Ð Unique design, aluminum-alloy
²Camshafts Ð special design intake and exhaust cams
²Flywheel weight Ð 18 lbs
²Fuel injectors Ð 19 lbs/hour
²Oil cooler Ð block mounted, water-to-oil cooler
²Engine cooling Ð heavy duty radiator core
²Exhaust Ð Quasi-dual exhaust
²Transaxle Ð MTX-75 5±speed with high performance clutch
Engine/Transmission
7
Page 8 of 16
Item Description
ConfigurationTransversely mounted, 60-degree
V6, cast aluminum block and
heads, iron cylinder liners, fully
counterweighted forged
crankshaft, crankshaft windage
tray, lightened flywheel, structural
aluminum-alloy oil pan
Bore x Stroke82.4 x 79.0 mm (3.24 x 3.11 in)
Displacement2 544 cc/155 cid
Compression ratio10.0:1
Horsepower (SAE net)149 kW (200 hp) @ 6 600 rpm
Torque226 Nm (167 lb/ft @ 5 500 rpm)
Redline6 750 rpm (fuel shut-off at
7 000 rpm)
Specific output78.6 hp per liter
ValvetrainDual overhead chain-driven cams,
roller finger followers with
hydraulic lash adjustment,
ovate-wire valve springs, four
valves per cylinder. The Extrude
Honeyprocess is used on the
primary and secondary ports
Fuel systemSequential electronic fuel injection,
19 lb/hr injectors, 379 kPa (55 psi)
Mass air sensor70 mm (2.76 in) diameter
Throttle body60 mm (2.36 in) diameter bore
Port throttlesElectronically actuated 32 mm
(1.26 in) diameter bore-open at
3 250 rpm
Exhaust manifoldsSteel tube clamshell design
Exhaust system57 mm (2.25 in) diameter with
63.5 mm (2.50 in) polished
stainless steel tips
Engine/Transmission
8
Page 13 of 16
FLUID RECOMMENDATIONS
Fluid capacities:
Please refer to your Contour Owner's Guide.
Fuel recommendation:
91 Octane or higher
Regular fuel can be used in the SVT Contour without damaging
engine components. The knock sensor will adjust the engine
calibration to accomodate regular unleaded fuel. This may result in
a degradation of engine performance.
SYNTHETIC FLUIDS
There are no synthetic fluids or break-in fluids in your SVT Contour
when it leaves the factory. Note that SVT does not make
recommendations about the use of synthetic oils in your vehicle. Should
you decide to use synthetic engine oil, we recommend you allow 4 000 to
6 000 miles (6 500 km to 9 600 km) in order to assure complete break-in
before switching to synthetic oil.
MAINTENANCE AND BREAK-IN
For complete maintenance and break-in procedure information, please
refer to your Contour Owner's Guide.
91(R+M)/2 METHOD
Maintenance
13
