applicable. These procedures can be found in ser-
vice manual procedures. Following these proce-
dures is very important to the safety of individuals
performing diagnostic tests.
4.2.2 VEHICLE PREPARATION FOR
TESTING
Make sure the vehicle being tested has a fully
charged battery. If it does not, false diagnostic codes
or error messages may occur.
4.2.3 SERVICING SUB-ASSEMBLIES
Some components of the powertrain system are
intended to be serviced in assembly only. Attempt-
ing to remove or repair certain system sub-
components may result in personal injury and/or
improper system operation. Only those components
with approved repair and installation procedures in
the service manual should be serviced.
4.2.4 DRBIIITSAFETY INFORMATION
WARNING: EXCEEDING THE LIMITS OF THE
DRB MULTIMETER IS DANGEROUS. IT CAN
EXPOSE YOU TO SERIOUS INJURY.
CAREFULLY READ AND UNDERSTAND THE
CAUTIONS AND THE SPECIFICATION
LIMITS.
Follow the vehicle manufacturer 's service specifi-
cations at all times.
²Do not use the DRBIIItif it has been damaged.
²Do not use the test leads if the insulation is
damaged or if metal is exposed.
²To avoid electrical shock, do not touch the test
leads, tips or the circuit being tested.
²Choose the proper range and function for the
measurement. Do not try voltage or current mea-
surements that may exceed the rated capacity.
²Do not exceed the limits shown in the table below:
FUNCTION INPUT LIMIT
Volts 0 - 500 peak volts AC
0 - 500 volts DC
Ohms (resistance)* 0 -1.12 megohms
Frequency Measured
Frequency Generated0-10kHz
Temperature -58 - 1100ÉF
-50 - 600ÉC
* Ohms cannot be measured if voltage is present.
Ohms can be measured only in a non-powered
circuit.
²Voltage between any terminal and ground must
not exceed 500v DC or 500v peak AC.
²Use caution when measuring voltage above 25v
DC or 25v AC.
²The circuit being tested must be protected by a
10A fuse or circuit breaker.
²Use the low current shunt to measure circuits up
to 10A. Use the high current clamp to measure
circuits exceeding 10A.
²When testing for the presence of voltage or cur-
rent, make sure the meter is functioning cor-
rectly. Take a reading of a known voltage or
current before accepting a zero reading.
²When measuring current, connect the meter in
series with the load.
²Disconnect the live test lead before disconnecting
the common test lead.
²When using the meter function, keep the DRB
away from spark plug or coil wires to avoid
measuring error from outside interference.
4.3 WARNINGS AND CAUTIONS
4.3.1 ROAD TEST WARNINGS
Some complaints will require a test drive as part
of the repair verification procedure. The purpose of
the test drive is to try to duplicate the diagnostic
code or symptom condition.
CAUTION: BEFORE ROAD TESTING A
VEHICLE, BE SURE THAT ALL
COMPONENTS ARE REASSEMBLED.
DURING THE TEST DRIVE, DO NOT TRY TO
READ THE DRB SCREEN WHILE IN MOTION.
DO NOT HANG THE DRB FROM THE REAR
VIEW MIRROR OR OPERATE IT YOURSELF.
HAVE AN ASSISTANT AVAILABLE TO
OPERATE THE DRB.
4.3.2 VEHICLE DAMAGE CAUTIONS
Before disconnecting any control module, make
sure the ignition is ªoffº. Failure to do so could
damage the module.
When testing voltage or continuity at any control
module, use the terminal side (not the wire end) of
the connector. Do not probe a wire through the
insulation; this will damage it and eventually cause
it to fail because of corrosion.
Be careful when performing electrical tests so as
to prevent accidental shorting of terminals. Such
mistakes can damage fuses or components. Also, a
second code could be set, making diagnosis of the
original problem more difficult.
12
GENERAL INFORMATION
ProCarManuals.com
Symptom:
P-0171±1/1 FUEL SYSTEM LEAN
When Monitored and Set Condition:
P-0171±1/1 FUEL SYSTEM LEAN
When Monitored: With the engine running in closed loop mode, the ambient, battery
temperature above Ð5 deg. C (20 deg. F) and altitude below 8000 ft.
Set Condition: If the PCM multiplies short term compensation by long term adaptive and
a certain percentage is exceeded for two trips, a freeze frame is stored, the MIL illuminates
and a trouble code is stored.
POSSIBLE CAUSES
FUEL PUMP MODULE DEFECTIVE
TPS VOLTAGE CHANGE NOT SMOOTH
TPS VOLTAGE <0.92V
FUEL INLET STRAINER PLUGGED
ECT SENSOR DEFECTIVE (OUT OF CALIBRATION)
MAP SENSOR DEFECTIVE (OUT OF CALIBRATION)
ENGINE MECHANICAL PROBLEM
FUEL FILTER/PRESSURE REGULATOR DEFECTIVE (HIGH)
FUEL FILTER/PRESSURE REGULATOR DEFECTIVE (LOW)
FUEL PUMP CAPACITY (VOLUME) OUT OF SPECS
TEST ACTION APPLICABILITY
1 Turn ignition on.
With the DRB, read the DTC's.
Is the Global Good Trip Counter displayed and equal to zero for P0171?All
Ye s®Go To 2
No®Go To 13
2 Ignition On, Engine Not Running
With the DRB, read the TPS voltage.
While monitoring the DRB, slowly open and close the Throttle.
Is the voltage change smooth?All
Ye s®Go To 3
No®Replace the Throttle Position Sensor.
Perform Powertrain Verification Test VER-5A.
75
DRIVEABILITY
ProCarManuals.com
