2000 CHRYSLER VOYAGER oil

Verification Tests
VERIFICATION TEST VER-1A APPLICABILITY
No Start Verification
Use this test to verify that a No Start condition has been repaired and that the vehicle can be
returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary
3. Attempt to start the engine.
4. If the No Start condition is still present, refer to the symptom list and perform diagnostic
testing as necessary. Refer to any Technical Service Bulletins that may apply.
5. Run the engine for one warm-up cycle to verify proper operation. With the DRBIIIt, confirm
that no DTC's are present and that all components are functioning properly.
6. If DTC's are present, refer to the symptom list and perform diagnostic testing as necessary.ALL
VERIFICATION TEST VER-2A APPLICABILITY
Non-OBDII Verification
Use this test to verify that a non-OBDII symptom has been repaired and that the vehicle can
be returned to the customer. A non-OBDII symptom is a comprehensive component related
symptom that is not the result of a failed OBDII major monitor.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and the
SKIM modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programming information for the PCM, SKIM
and the Transponder (ignition key).
1. Inspect the vehicle to ensure that all components related to the repair are connected
properly.
2. With the DRBIIIt, Clear DTC's and Reset Memory (all engine values).
3. Run the engine for one warm-up cycle to verify proper operation.
4. Road test the vehicle. Use all accessories that may be related to this repair.
With the DRBIIIt, confirm that no DTC's are present and that all components are functioning
properly.
6. If this test is being performed after a No Trouble Code test, verify that the symptom is no
longer present. If the symptom is still present, or any other symptom or DTC is present, refer
to the symptom list for further diagnostic testing procedures. Check for any Technical Service
Bulletins that may apply.
7. If there are no DTC's present and all components are functioning properly, repair is
complete.ALL
317
VERIFICATION TESTS
ProCarManuals.com

Powertrain Verification Test VER-7A APPLICABILITY
SKIS Verfication
Use this test to verify that SKIM system symptom has been repaired and that the vehicle can
be returned to the customer.
Note: If the Powertrain Control Module has been replaced and the correct VIN and
mileage have not been programmed, a DTC will be set in the ABS, Airbag and SKIM
modules. In addition, if the vehicle is equipped with a Sentry Key Immobilizer
Module (SKIM), Secret Key data must be updated to enable starting. Refer to
GENERAL INFORMATION section for programmig information for the PCM, SKIM
and the Transponder (ignition key).
1.Inspect the vehicle to ensure that all components related to the repair are connected properly.
2. Inspect the engine oil for fuel contamination. Replace the oil and filter as necessary.
3. Start the engine.
4. Run the engine for one warm-up cycle to verify proper operation. With the DRBIIIt, confirm
that no DTCs are present and that all components are functioning properly. If the DTC is still
present refer to any Technical Service Bulletins that may apply.
5. If a different DTC(s) is present, refer to the symtom list and perform diagnostic testing as
necessary. If there are no DTCs present and all components are functioning correctly, repair is
now complete.All
322
VERIFICATION TESTS
Verification Tests ÐContinued
ProCarManuals.com

DATA LINK CONNECTOR - BLACK 16 WAYCAV CIRCUIT FUNCTION
1- -
2- -
3 D1 20VT/BR CCD BUS (+)
4 Z2 20BK/LG GROUND
5 Z11 20BK/WT GROUND
6 D20 20LG SCI RECEIVE
7 D21 20PK SCI TRANSMIT
8- -
9- -
10 - -
11 D2 20WT/BK CCD BUS (-)
12 - -
13 - -
14 D6 20PK/LB SCI RECEIVE
15 - -
16 M1 20PK FUSED B(+)
EGR SOLENOID - GRAY 2 WAYCAV CIRCUIT FUNCTION
1 K35 18GY/YL EGR SOLENOID CONTROL
2 F87 18WT/BK FUSED IGNITION SWITCH OUTPUT (ST-RUN)
ENGINE COOLANT TEMPERATURE SENSOR - BLACK 2 WAYCAV CIRCUIT FUNCTION
1 K4 18BK/LB SENSOR GROUND
2 K2 18TN/BK ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
ENGINE OIL PRESSURE SWITCH - GREEN 2 WAYCAV CIRCUIT FUNCTION
1 G6 16GY ENGINE OIL PRESSURE SWITCH SENSE
2- -
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
336
CONNECTOR PINOUTS
ProCarManuals.com

IDLE AIR CONTROL MOTOR - BLACK 4 WAYCAV CIRCUIT FUNCTION
1 K59 18VT/BK IDLE AIR CONTROL NO. 4 DRIVER
2 K40 18BR/WT IDLE AIR CONTROL NO. 3 DRIVER
3 K60 18YL/BK IDLE AIR CONTROL NO. 2 DRIVER
4 K39 18GY/RD IDLE AIR CONTROL NO. 1 DRIVER
IGNITION COIL PACK (2.0L/2.4L) - BLACK 3 WAYCAV CIRCUIT FUNCTION
1 K17 18DG/TN IGNITION COIL NO. 2 DRIVER
2 A142 18DG/OR AUTOMATIC SHUT DOWN RELAY OUTPUT
3 K19 18GY/RD IGNITION COIL NO. 1 DRIVER
IGNITION COIL PACK (3.3L/3.8L) - BLACK 4 WAYCAV CIRCUIT FUNCTION
1 K17 18DB/TN (3.3L) IGNITION COIL NO 2 DRIVER
1 K18 18RD/YL (3.8L) IGNITION COIL NO 3 DRIVER
2 A142 18DG/OR (3.3L) AUTOMATIC SHUT DOWN RELAY OUTPUT
2 K19 18GY/RD (3.8L) IGNITION COIL NO 1 DRIVER
3 A142 18DG/OR (3.8L) AUTOMATIC SHUT DOWN RELAY OUTPUT
3 K19 18GY/RD (3.3L) IGNITION COIL NO 1 DRIVER
4 K17 18DB/TN (3.8L) IGNITION COIL NO 2 DRIVER
4 K18 18RD/YL (3.3L) IGNITION COIL NO 3 DRIVER
INSTRUMENT CLUSTER - BLACK 13 WAYCAV CIRCUIT FUNCTION
1- -
2 M1 20PK FUSED B(+)
3- -
4- -
5- -
6 E2 20OR PANEL LAMPS FEED
7 Z2 20BK/LG GROUND
8- -
9 D2 20WT/BK CCD BUS (-)
10 D1 20VT/BR CCD BUS (+)
11 F11 20RD/WT FUSED IGNITION SWITCH OUTPUT (ST-RUN-OFF)
12 - -
13 Z1 20BK GROUND
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
341
CONNECTOR PINOUTS
ProCarManuals.com

POWERTRAIN CONTROL MODULE C1 - BLACK 40 WAYCAV CIRCUIT FUNCTION
1- -
2 K18 18RD/YL IGNITION COIL NO. 3 DRIVER
3 K17 18DB/TN IGNITION COIL NO. 2 DRIVER
4- -
5 V32 18YL/RD SPEED CONTROL ON/OFF SWITCH SENSE
6 A142 18DG/OR AUTOMATIC SHUT DOWN RELAY OUTPUT
7 K13 18YL/WT FUEL INJECTOR NO. 3 DRIVER
8 K20 18DG GENERATOR FIELD DRIVER (+)
9- -
10 Z12 18BK/TN GROUND
11 K19 18GY/RD IGNITION COIL NO. 1 DRIVER
12 - -
13 K11 18WT/DB FUEL INJECTOR NO. 1 DRIVER
14 K58 18BR/DB FUEL INJECTOR NO. 6 DRIVER
15 K38 18GY FUEL INJECTOR NO. 5 DRIVER
16 K14 18LB/BR FUEL INJECTOR NO. 4 DRIVER
17 K12 18TN/WT FUEL INJECTOR NO. 2 DRIVER
18 - -
19 - -
20 F87 18WT/BK FUSED IGNITION SWITCH OUTPUT (ST-RUN)
21 - -
22 G3 18BK/PK SERVICE ENGINE SOON INDICATOR DRIVER
23 - -
24 - -
25 K42 18DB/LG KNOCK SENSOR SIGNAL
26 K2 18TN/BK ENGINE COOLANT TEMPERATURE SENSOR SIGNAL
27 K127 18BK/OR OXYGEN SENSOR GROUND
28 - -
29 - -
30 K41 18BK/DG OXYGEN SENSOR 1/1 SIGNAL
31 K90 18TN (EXCEPT 3.0L) SMART START RELAY CONTROL
32 K24 18GY/BK CRANKSHAFT POSITION SENSOR SIGNAL
33 K44 18TN/YL CAMSHAFT POSITION SENSOR SIGNAL
34 - -
35 K22 18OR/DB THROTTLE POSITION SENSOR SIGNAL
36 K1 18DG/RD MANIFOLD ABSOLUTE PRESSURE SENSOR SIGNAL
37 K21 18BK/RD (2.4L) INTAKE AIR TEMPERATURE SIGNAL
38 C103 18DG/LB (EXCEPT
3.0L)A/C SWITCH SIGNAL
39 - -
40 K35 18GY/YL EGR SOLENOID CONTROL
C
O
N
N
E
C
T
O
R
P
I
N
O
U
T
S
349
CONNECTOR PINOUTS
ProCarManuals.com