2000 CHRYSLER VOYAGER fuel pressure

TEST ACTION APPLICABILITY
11Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Remove the Fuel Pump Module and inspect the Fuel Inlet Strainer.
Is the Fuel Inlet Strainer plugged?All
Ye s®Replace the Fuel Inlet Strainer.
No®Go To 12
12 If there are no potential causes remaining, the Fuel Pump Module is assumed to be
defective.
View repair options.All
Repair
Replace the Fuel Pump Module
13 Check for any of the following conditions/mechanical problems.
ENGINE VACUUM Ð must be at least 13 inches in neutral
ENGINE VALVE TIMING Ð must be within specifications
ENGINE COMPRESSION Ð must be within specifications
ENGINE EXHAUST SYSTEM Ð must be free of any restrictions or leaks.
ENGINE PVC SYSTEM Ð must flow freely
TORQUE CONVERTER STALL SPEED Ð must be within specifications
POWER BRAKE BOOSTER Ð no internal vacuum leaks
FUEL - must be free of contamination
FUEL INJECTOR Ð plugged or restricted injector; control wire not connected to
correct injector
Are there any engine mechanical problems?All
Ye s®Repair as necessary.
Perform FUEL SYSTEM/MISFIRE MONITOR VERIFICATION
TEST
No®Test Complete.
14 The conditions required to set the DTC are no longer present.
With the DRB read and record the freeze frame data and the ªFuel System Similar
Conditions Window'' data.
Utilize the data and try to duplicate the operating conditions at which the DTC was
set. Pay particular attention to the ECT and RPM for added diagnostics.
Note: Refer to any TSB's that may apply to the symptom.
Test Complete
Repair
Test Complete.
82
P0172 -1/1 FUEL SYSTEM RICH ÐContinued
ProCarManuals.com

POSSIBLE CAUSES
OTHER POSSIBLE CAUSES FOR MIS-FIRE
CAM, CRANK, VALVE TIMING, OR VACUUM PROBLEM
ELECTRONIC IGNITION COIL OUTPUT LOW
ENGINE MECHANICAL PROBLEM
SECONDARY IGNITION PATTERN IRREGULAR
FUEL CONTAMINATION
FUEL PRESSURE LEAK DOWN OUT OF SPECIFICATION
FUEL PUMP AMPERAGE OUT OF SPECIFICATION
FUEL PUMP CAPACITY OUT OF SPECIFICATION
FUEL PUMP PRESSURE OUT OF SPECIFICATION
MIS-FIRE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the MIS-FIRE GOOD TRIP counter displayed and equal to zero?All
Ye s®Go To 2
No®Go To 3
2 At this time the conditions that set this fault are present.
With the DRB, read the FREEZE FRAME and SIMILAR CONDITIONS WINDOWS.
Attempt to operate the vehicle in the similar conditions.
When the vehicle is operating in the SIMILAR CONDITIONS WINDOW, go to the
WHICH CYLINDER IS MISFIRING screen.
Is the DRB counting mis-fires at this time?All
Ye s®Go To 4
No®Go To 3
3 At this time the mis-fire does not exist or is an intermittent problem.
With the DRB, read the FREEZE FRAME and SIMILAR CONDITIONS WINDOW.
With these screens, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME pay particular attention to the fault setting condi-
tions, such as speed, temp, load, and map vacuum.
Does the mis-fire reoccur?All
Ye s®Go To 4
No®Mis-fire no longer exists.
Perform VERIFICATION TEST VER-5A2.
4 With the DRB, read the FREEZE FRAME DATA.
Use the freeze frame data and attempt to determine the cause.
In the FREEZE FRAME, are the adaptive fuel percentages greater than +/- 15%?All
Ye s®Go To 5
No®Go To 10
101
DRIVEABILITY
P-0300 MULTIPLE CYLINDER MIS-FIRE ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
5 With an appropriate container, obtain a fuel sample from the vehicle.
Is the fuel free from contamination?All
Ye s®Go To 6
No®Replace contaminated fuel and clean system.
Perform VERIFICATION TEST VER-5A2.
6 Perform Fuel Pressure Leak Down Test per service instructions.
Did the Fuel Pressure Leak Down Test pass?All
Ye s®Go To 7
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
7 Perform Fuel Pump Amperage Test per service instructions.
Did the Fuel Pump Amperage Test pass?All
Ye s®Go To 8
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
8 Perform Fuel Pump Capacity Test per service instructions.
Did the Fuel Pump Capacity Test pass?All
Ye s®Go To 9
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
9 Perform Fuel Pump Pressure Test per service instructions.
Did the Fuel Pump Pressure Test pass?All
Ye s®Go To 10
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
10 With the DRB, read the FREEZE FRAME DATA.
Use the freeze frame data and attempt to determine the cause.
In the FREEZE FRAME, is the LOAD VALUE over 50% and the temp normal
operating temp normal?All
Ye s®Go To 12
No®Go To 11
11 With the DRB, read the FREEZE FRAME window.
Use the freeze frame data and attempt to determine the cause.
In the FREEZE FRAME, is the ENGINE RPM over 3000 and the operating temp
normal?All
Ye s®Lab scope cam and crank sensor, check valve timing, running
vacuum test.
Perform VERIFICATION TEST VER-5A2.
No®Go To 14
102
DRIVEABILITY
P-0300 MULTIPLE CYLINDER MIS-FIRE ÐContinued
ProCarManuals.com

Symptom List:
P-0305 CYLINDER #5 MIS-FIRE
P-0306 CYLINDER #6 MIS-FIRE
Test Note: All symptoms listed above are diagnosed using the same tests.
The title for the tests will be P-0305 CYLINDER #5 MIS-FIRE.
When Monitored and Set Condition:
P-0305 CYLINDER #5 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
P-0306 CYLINDER #6 MIS-FIRE
When Monitored: With the engine running, after successfully performing Crank Sensor
learn.
Set Condition: When more than a 2% misfire rate is measured during two trips, or with
a 10% to 30% misfire rate during one trip.
POSSIBLE CAUSES
OTHER POSSIBLE CAUSES FOR MIS-FIRE
CAM, CRANK, VALVE TIMING, OR VACUUM PROBLEM
ELECTRONIC IGNITION COIL OUTPUT LOW
ENGINE MECHANICAL PROBLEM
SECONDARY IGNITION PATTERN IRREGULAR
FUEL CONTAMINATION
FUEL PRESSURE LEAK DOWN OUT OF SPECIFICATION
FUEL PUMP AMPERAGE OUT OF SPECIFICATION
FUEL PUMP CAPACITY OUT OF SPECIFICATION
FUEL PUMP PRESSURE OUT OF SPECIFICATION
MIS-FIRE DOES NOT REOCCUR
TEST ACTION APPLICABILITY
1 With the DRB, read the DTCs.
Is the MIS-FIRE GOOD TRIP counter displayed and equal to zero?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV Ye s®Go To 2
No®Go To 3
104
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
2 At this time the conditions that set this fault are present.
With the DRB, read the FREEZE FRAME DATA and SIMILAR CONDITIONS
WINDOWS.
Attempt to operate the vehicle in the similar conditions.
When the vehicle is operating in the SIMILAR CONDITIONS window, go to the
WHICH CYLINDER IS MISFIRING monitor.
Is the DRB counting mis-fires at this time?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 4
No®Go To 3
3 At this time the mis-fire does not exist or is an intermittent problem.
With the DRB, read the FREEZE FRAME DATA and SIMILAR CONDITIONS
WINDOW.
With these screens, attempt to duplicate the condition that has set this fault.
While using FREEZE FRAME DATA pay particular attention to the fault setting
conditions, such as speed, temp, load, and map vacuum.
Does the mis-fire reoccur?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 4
No®Mis-fire no longer exists.
Perform VERIFICATION TEST VER-5A2.
4 With the DRB, read the FREEZE FRAME DATA.
Use the freeze frame data and attempt to determine the cause of the misfire.
In the FREEZE FRAME, are the adaptive fuel percentages greater than +/- 15
percent?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 5
No®Go To 10
5 With an appropriate container, obtain a fuel sample from the vehicle.
Is the fuel free from contamination?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 6
No®Replace contaminated fuel and clean system.
Perform VERIFICATION TEST VER-5A2.
6 Perform Fuel Pressure Leak Down Test per service instructions.
Did the Fuel Pressure Leak Down Test pass?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 7
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
105
DRIVEABILITY
P-0305 CYLINDER #5 MIS-FIRE ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
7 Perform Fuel Pump Amperage Test per service instructions.
Did the Fuel Pump Amperage Test pass?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 8
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
8 Perform Fuel Pump Capacity Test per service instructions.
Did the Fuel Pump Capacity Test pass?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 9
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
9 Perform Fuel Pump Pressure Test per service instructions.
Did the Fuel Pump Pressure Test pass?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 10
No®Relieve fuel pressure and repair as necessary.
Perform VERIFICATION TEST VER-5A2.
10 With the DRB, read the FREEZE FRAME DATA.
Use the freeze frame data and attempt to determine the cause of the misfire.
In the FREEZE FRAME, is the LOAD VALUE over 50% and the temp normal
operating temp?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 11
No®Go To 13
11 Engine Off.
Connect a suitable engine analyzer to the engine.
Allow the Engine to idle.
NOTE: If the Engine will not idle, maintain a constant RPM above idle.
NOTE: Set the scope to read display or parade pattern.
Remove any spark plug wire.
Observe the Secondary KV Line.
Is the open secondary voltage at least 25 KV?ENGINE - 3.0L V6
and/or ENGINE -
3.3L V6 and/or EN-
GINE - 3.8L V6
and/or ENGINE -
3.3L V6 FFV
Ye s®Go To 12
No®Replace the Electonic Ignition Coil.
Perform VERIFICATION TEST VER-5A2.
106
DRIVEABILITY
P-0305 CYLINDER #5 MIS-FIRE ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
3Note: Leaving the Gas Cap loose could cause this trouble code to set.
To continue testing you will need Miller Tool Kit #6872A and #8382.
NOTE: The Fuel Tank must have 1/2 tank of fuel to perform this test.
Perform Evaporative System Pressure Pump Self Test that is specified on the tester
cover.
Warning: Verify the vehicle fuel tank contains at least 3 gallons of fuel.
Attach the DRB III to the vehicle.
Turn the Key On.
At: ENGINE SYSTEM TESTS select: LEAK DETECTION PUMP TEST.
Read instructions and then press ENTER.
At: LEAK DETECTION PUMP TEST select #3 HOLD PSI.
At the vacuum hose going to the LDP, attach and apply a continuous vacuum (i.e. 209
Hg).
Remove Gas Cap.
Install 8382 on the Gas Cap and on the vehicle.
Attach the supply hose from 6872A to 8382.
Attach the power source from the 6872A, clip to Battery(+) and ground clip to
Battery(-).
On the 6872A set the Pressure/Hold Valve to Open and set the Vent Valve to Closed.
Turn the timer on and watch the gauge.
When the gauge pressure reaches 14 in. H2O, turn the Pressure/Hold Valve to
Closed.
Turn the timer off. Note the time and pressure.
Did pressure drop more than 6 in. H2O (to 8 inches H2O on the gauge) in two
minutes?All
Ye s®Go To 4
No®Go To 5
141
DRIVEABILITY
P-0442 EVAP LEAK MONITOR SMALL LEAK DETECTED ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
4 To continue testing you will need Miller Tool Kit #6872A, #8382 and #6904 Ultrasonic
Leak Detector.
NOTE: The Fuel Tank must have 1/2 tank of fuel to perform this test.
Perform Evaporative System Pressure Pump Self Test that is specified on the tester
cover.
Warning: Verify the vehicle fuel tank contains at least 3 gallons of fuel.
Attach the DRB III to the vehicle.
Turn the Key On.
At: ENGINE SYSTEM TESTS select: LEAK DETECTION PUMP TEST.
Read instructions and then press ENTER.
At: LEAK DETECTION PUMP TEST select #3 HOLD PSI.
At the vacuum hose going to the LDP, attach and apply a continuous vacuum (i.e. 209
Hg).
Remove Gas Cap.
Install 8382 on the Gas Cap and on the vehicle.
Attach the supply hose from 6872A to 8382.
Attach the power source from the 6872A, clip to Battery(+) and ground clip to
Battery(-).
Set Pressure Hold to Open and set Vent to Open.
Turn Pump Timer On.
To prevent noise from interfering with test, move tool #6872 away from vehicle.
Using the Ultrasonic Leak Detector, start listening for leaks at Gas Cap then proceed
to Rollover Valve, Canister, Leak Detection Pump, and Evap Purge Solenoid.
Were any leaks heard with the Ultrasonic Leak Detector?All
Ye s®Repair or replace leaking component.
Perform VERIFICATION TEST VER-6A.
No®Replace Leak Detection Pump.
Perform VERIFICATION TEST VER-6A.
5 At this time, the condition required to set the code is not present.
Using the schematic as a guide, inspect the wiring, connectors and hoses.
Were any problems found?All
Ye s®Repair as necessary.
Perform VERIFICATION TEST VER-6A.
No®Test Complete.
142
DRIVEABILITY
P-0442 EVAP LEAK MONITOR SMALL LEAK DETECTED ÐContinued
ProCarManuals.com