2000 CHRYSLER VOYAGER Diagnostic Manual

TEST ACTION APPLICABILITY
4 Ignition Off
Remove the Air Conditioning Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Using a Voltmeter, measure the Fused Ignition Switch Output Circuit.
Is the voltage above 10.0 volts?All
Ye s®Go To 5
No®Repair the open Fused Ignition Switch Output Circuit.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Remove the Air Conditioning Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance between terminals C (85) and A (86) of
the Air Conditioning Clutch Relay.
Is the resistance below between 50 to 90 ohms?All
Ye s®Go To 6
No®Replace the Air Conditioning Clutch Relay.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the PCM grey connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the A/C Clutch Control Circuit from the PCM
connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Air Conditioning Clutch Relay Control Circuit for a
short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 7
7 Ignition Off
Disconnect the PCM grey connector.
Remove the Air Conditioning Clutch Relay.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, measure the resistance of the Air Conditioning Clutch Relay
Control Circuit from the relay to the PCM.
Is the resistance below 5.0 ohms?All
Ye s®Go To 8
No®Repair open Air Conditioning Clutch Relay Control Circuit.
Perform Powertrain Verification Test VER-2A.
8 Ignition Off
If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
171
DRIVEABILITY
P-0645 A/C CLUTCH RELAY CIRCUIT ÐContinued
ProCarManuals.com

Symptom:
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED
When Monitored and Set Condition:
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED
When Monitored: With engine running. The PCM expects the signal to be high for 16
cycles while it monitors the brake switch signal during accel and decel modes.
Set Condition: After the vehicle speed increases, the PCM must accumulate 6 seconds
while delta throttle voltage is above 0.02 volt. The count is reset to zero whenever the
brake switch indicates a low signal.
POSSIBLE CAUSES
BRAKE SWITCH GROUND CIRCUIT OPEN
BRAKE SWITCH INTERNAL SHORT
BRAKE SWITCH SENSE CIRCUIT OPEN
BRAKE SWITCH SENSE CIRCUIT SHORT TO GROUND
PCM CONNECTOR OBSERVABLE DEFECT
PCM DEF (VOLTAGE HIGH)
PCM DEF (VOLTAGE LOW)
TEST ACTION APPLICABILITY
1 Ignition Off
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
Key on.
With a Voltmeter, measure the Brake Switch Sense Circuit at the Brake Switch
Connector.
Is the voltage above 9.0 volts?All
Ye s®Go To 2
No®Go To 5
2 Ignition Off
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Ground Circuit at the Brake Switch
Connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 3
No®Repair the Brake Switch Ground Circuit.
Perform Powertrain Verification Test VER-2A.
172
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition off.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
Ignition on with engine not running.
Monitor Brake Switch status on the DRB while performing the next step.
Connect a jumper across the Brake Switch Circuit to Ground Circuit.
Did the DRB change from9pressed9to9released9?All
Ye s®Replace or adjust the Brake Switch.
Perform Powertrain Verification Test VER-2A.
No®Go To 4
4 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
5 Ignition Off
Disconnect the Powertrain Control Module.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Sense Circuit resistance from the
PCM to the Brake Switch Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 6
No®Repair the Brake Switch Sense Circuit for an open.
Perform Powertrain Verification Test VER-2A.
6 Ignition Off
Disconnect the Powertrain Control Module.
Note: Check connectors - Clean/repair as necessary.
Is any terminal damaged, pushed out, or miswired?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Go To 7
7 Ignition Off
Disconnect the Powertrain Control Module.
Disconnect the Brake Switch Connector.
Note: Check connectors - Clean/repair as necessary.
With an Ohmmeter, measure the Brake Switch Sense Circuit to a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Brake Switch Sense Circuit for a short to ground.
Perform Powertrain Verification Test VER-2A.
No®Go To 8
173
DRIVEABILITY
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED ÐContinued
ProCarManuals.com

TEST ACTION APPLICABILITY
8 If there are no potential causes remaining, the Powertrain Control Module is
assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-2A.
174
DRIVEABILITY
P-0703 BRAKE SWITCH STUCK PRESSED OR RELEASED ÐContinued
ProCarManuals.com

Symptom:
P-1195 SLOW 1/1 O2S DURING CATALYST MONITOR
When Monitored and Set Condition:
P-1195 SLOW 1/1 O2S DURING CATALYST MONITOR
When Monitored: With the engine running, coolant greater than 76 deg C (170 deg F),
open throttle, steady to slight increasing vehicle speed > 28 Km/h (18 mph) < 88 Km/h (55
mph), with a light load on the engine, for a period no less than five minutes.
Set Condition: The upstream oxygen sensor signal voltage is switching from below 0.39
volt to above 0.6 volt and back fewer times than required.
POSSIBLE CAUSES
OXYGEN SENSOR GROUND CIRCUIT OPEN
1/1 OXYGEN SENSOR CONNECTOR OBSERVABLE DEFECT
1/1 OXYGEN SENSOR DEFECTIVE
ENGINE FLUID CONSUMPTION
EXHAUST SYSTEM LEAKING
PCM CONNECTOR OBSERVABLE DEFECT
TEST ACTION APPLICABILITY
1 Start Engine
Note: Check the Exhaust for excessive smoke caused by oil or coolant
consumption.
Is there an oil or coolant consumption condition present?All
Ye s®Repair engine mechanical as necessary, and replace Upstream O2
Sensor.
Perform Powertrain Verification Test VER-5A.
No®Go To 2
2 Start Engine
Check the Exhaust System for leaks between Engine and Catalytic Converter.
Is there any Exhaust leak?All
Ye s®Repair or replace leaking Exhaust parts as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 3
175
DRIVEABILITY
ProCarManuals.com

TEST ACTION APPLICABILITY
3 Ignition Off
Disconnect the Upstream Oxygen Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance from the O2 Sensor Ground Circuit to
a good ground.
Is the resistance below 5.0 ohms?All
Ye s®Go To 4
No®Repair the open Sensor Ground Circuit to the Upstream Oxygen
Sensor.
Perform Powertrain Verification Test VER-5A.
4 Ignition Off
Disconnect the Upstream Oxygen Sensor Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect the Connectors and Terminals.
Is any Terminal damaged, pushed out or miswired?All
Ye s®Repair or replace as necessary.
Perform Powertrain Verification Test VER-5A.
No®Go To 5
5 Ignition Off
Disconnect the Powertrain Control Module Connector.
Note: Check connectors - Clean/repair as necessary.
Inspect the Connector.
Is the Connector condition OK?All
Ye s®Go To 6
No®Repair as necessary.
Perform Powertrain Verification Test VER-5A.
6 If there are no potential causes remaining, the Upstream Oxygen Sensor is assumed
to be defective.
View repair options.All
Repair
Replace the Upstream Oxygen Sensor.
Perform Powertrain Verification Test VER-5A.
176
DRIVEABILITY
P-1195 SLOW 1/1 O2S DURING CATALYST MONITOR ÐContinued
ProCarManuals.com

Symptom:
P-1281 ENGINE IS COLD TOO LONG
When Monitored and Set Condition:
P-1281 ENGINE IS COLD TOO LONG
When Monitored: Ignition key on, engine not running. Ambient temperature greater
than þ11ÉC (-11ÉF) and coolant temperature greater than þ7ÉC (19ÉF)
Set Condition: The engine does not warm to 79 degrees C (176 degrees F) while driving
for 20 minutes after start.
POSSIBLE CAUSES
ENGINE COLD TOO LONG
TEST ACTION APPLICABILITY
1 Start Engine
Drive vehicle under normal driving conditions for 20 minutes.
With the DRB, read Engine Coolant Temperature.
Did the engine warm to 79 degrees C (176 degrees F)?All
Ye s®Test Complete.
No®See pertinent service manual information for cooling system
diagnostics.
177
DRIVEABILITY
ProCarManuals.com

Symptom:
P1282 FUEL PUMP RELAY CONTROL CIRCUIT
When Monitored and Set Condition:
P±1282 FUEL PUMP RELAY CONTROL CIRCUIT
When Monitored: With the ignition key on and battery voltage greater than 10 volts.
Set Condition: An open or shorted condition is detected in the fuel pump relay control
circuit.
POSSIBLE CAUSES
FUSED IGNITION SWITCH OUTPUT CIRCUIT OPEN
FUEL PUMP RELAY DEFECTIVE
FUEL PUMP RELAY CONTROL CIRCUIT OPEN
FUEL PUMP RELAY CONTROL CIRCUIT SHORT TO GROUND
FUEL PUMP RELAY WIRING HARNESS INTER DEF
FUEL PUMP RELAY WIRING HARNESS OBS DEF
PCM DEFECTIVE
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running
With the DRB, actuate the Fuel Pump Relay.
Is the Fuel Pump Relay clicking?All
Ye s®Go To 2
No®Go To 4
2 Ignition On, Engine Not Running
With the DRB actuate the Fuel Pump Relay.
Wiggle the Wiring Harness from the Relay to the PCM.
Did the Fuel Pump Relay clicking stop or become erratic while wiggling the wires?All
Ye s®Repair Circuit as necessary where wiggling caused the clicking to
become erratic.
Perform Powertrain Verification Test VER-2A.
No®Go To 3
3 Ignition Off
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-2A.
No®Test Complete.
178
DRIVEABILITY
ProCarManuals.com