2000 CHRYSLER VOYAGER ignition

Certain criteria must be met for a diagnostic
trouble code to be entered into the SKIM memeory.
The criteria may be a range of; Input voltage, CCD
Bus message, or coded messages to the SKIM. If all
of the criteria for monitoring a circuit or function
are met and a fault is sensed, a diagnostic trouble
code will be stored in the SKIM memory.
3.2.8 SKIS OPERATION
When ignition power is supplied to the SKIM, the
SKIM performs an internal self-test. After the self-
test is completed, the SKIM neergizes the antenna
(this activates the transponder chop responds to the
challenge by generating an encrypted response
message using the following:
Secret Key -This is an electronically stored
value (identification number) that is unique to each
SKIS. The secret key is stored in the SKIM, PCM
and all ignition key tranponders.
Challenge -This is a random numbr that is
generated by the SKIM at each ignition key cycle.
The secret key and challenge are plugged into an
algorithm that produces the encrypted response
message. The transponder uses the crypto algo-
rithm to receive, decode and respond to the message
sent by the SKIM. After responding to the coded
message, the transponder sends a transponder ID
message to the SKIM. The SKIM compares the
transponder ID to the available valid key codes in
the SKIM memory (8 key maximum). After validat-
ing the key the SKIM sends a CCD Bus message
called a ``Seed Request'' to the engine controller
then waits for a PCM response. If the PCM does not
respond, the SKIM will send the seed request agian.
After three failed attempts the SKIM will stop
sending the seed request and store a trouble code. If
the PCM sends a seed response, the SKIM sends a
valid/invalid key message to the PCM. This is an
encrypted message that is generated using the
following:
VIN -Vehicle Identification Number
Seed -This is a random number that is generated
by the PCM at each ignition key cycle.
The VIN and seed are plugged into a rolling code
algorithm that encrypts the ``valid/invalid key'' mes-
sage. The PCM uses the rolling code algorithm to
receive, decode and respond to the valid/invalid key
message sent by the SKIM. After sending the valid/
invalid key massage the SKIM waits 3.5 seconds for
a PCM status message from the PCM. If the PCM
does not respond with a valid key message to the
SKIM, a fault is detected and a trouble code is
stored.
The SKIS incorporates a warning lamp (``ALARM
SET'') located in the message center. The lamp
receives switched ignition voltage and is hardwired
to the body control module. The lamp is actuated
when the SKIM sends a CCD Bus message to thebody controller requesting the lamp on. The body
controller then provides the ground for the lamp.
The SKIM will request lamp operation for the
following:
- bulb checks at ignition on
- to alert the vehicle operator to a SKIS malfunc-
tion
For all faults except transponder faults and VIN
mismatch, the lamp remains on steady. In the event
of a tranponder fault the light flashes at a rate of 1
Hz (once per second). If a fault is pesent the lamp
will emain on or flashing for the complete ignition
cycle. If a fault is stored in SKIM memory which
prevents the system form operating properly, the
PCM will allow the engine to start and run (for 2
seconds) up to six times. After the sixth attempt, the
PCM disables the starter relay until the fault is
corrected.
3.2.9 PROGRAMMING THE POWERTRAIN
CONTROL MODULE
Important Note:Before replacing the PCM for a
failed driver, control circuit or ground circuit, be
sure to check the related component/circuit integ-
rity for failures not detected due to a double fault in
the circuit. Most PCM driver/control circuit failures
are caused by internal failure to components (i.e.
12-volt pull-ups, drivers and ground sensors). These
failures are difficult to detect when a double fault
has occurred and only one DTC has set.
NOTE:IF THE PCM AND THE SKIM ARE
REPLACED AT THE SAME TIME, PROGRAM
THE VIN INTO THE PCM FIRST. ALL VEHICLE
KEYS WILL THEN NEED TO BE REPLACED
AND PROGRAMMED TO THE NEW SKIM.
The SKIS ``Secret Key'' is an ID code that is
unique to each SKIS. This code is programmed and
stored in the SKIM, engine controller and transpon-
der ship (ignition key). When replacing the PCM it
is necessary to program the secret key into the
PCM.
1. Turn the ignition on (transmission in park/
neutral).
2. Use the DRB and select ``THEFT ALARM'',
SKIM then MISCELLANEOUS''.
3. Select ``PCM REPLACED''.
4. Enter secured access mode by entering the vehi-
cle four-digit PIN.
6
GENERAL INFORMATION
ProCarManuals.com

NOTE:IF THREE ATTEMPTS ARE MADE TO
ENTER THE SECURE ACCESS MODE USING
AN INCORRECT PIN, SECURED ACCESS
MODE WILL BE LOCKED OUT FOR ONE
HOUR. TO EXIT THIS LOCKOUT MODE, TURN
THE IGNITION TO THE RUN POSITION FOR
ONE HOUR THEN ENTER THE CORRECT
PIN. (ENSURE ALL ACCESSORIES ARE
TURNED OFF. ALSO MONITOR THE
BATTERY STATE AND CONNECT A BATTERY
CHARGER IF NECESSARY).
5. Press ``ENTER'' to transfer the secret key (the
SKIM will send the secret key to the PCM).
3.2.10 PROGRAMMING THE SENTRY KEY
IMMOBILIZER MODULE
NOTE:IF THE PCM AND THE SKIM ARE
REPLACED AT THE SAME TIME, PROGRAM
THE VIN INTO THE PCM FIRST. ALL VEHICLE
KEYS WILL THEN NEED TO BE REPLACED
AND PROGRAMMMED TO THE NEW SKIM.
1. Turn the ignition on (transmission in park/
neutral).
2. Use the DRB and select ``THEFT ALARM'',
``SKIM'' then MISCELLLANEOUS.
3. Select ``SKIM MOSULE REPLACEMENT (GAS-
OLINE)''
4. Program the vehicle four-digit PIN into the
SKIM.
5. Select ``COUNTRY CODE'' and enter the correct
country.
NOTE:BE SURE TO ENTER THE CORRECT
COUNTRY CODE. IF THE INCORRECT
COUNTRY CODE IS PROGRAMMED INTO
SKIM, THE SKIM MUST BE REPLACED.
6. Select ``UPDATE VIN'' (the SKIM will learn the
VIN from the PCM).
7. Press ``ENTER'' to transfer the VIN (the PCM
will send the VIN to the SKIM).
8. The DRB will ask if you want to transfer the
secret key. Select ``ENTER'' to transfer secret key
from the PCM. This will ensure the current
vehicle ignition keys will still operate the SKIS
system.
3.2.11 PROGRAMMING THE IGNITION
KEYS TO THE SENTRY KEY
IMMOBILIZER MODULE
1. Turn the ignition on (transmission in park/
neutral).2. Use the DRB and select ``THEFT ALARM'',
``SKIM'' then ``MISCELLANEOUS''.
3. Select ``PROGRAM IGNITION KEYS''.
4. Enter secured access mode by entering the vehi-
cle four-digit PIN.
NOTE:A MAXIMUM OF EIGHT KEYS CAN BE
LEARNED TO EACH SKIM. ONCE A KEY IS
LEARNED TO A SKIM IT (THE KEY) CANNOT
BE RANFERRED TO ANOTHER VEHICLE.
If ignition key programming is unsuccessful, the
DRB will display one of the following messages:
Programming Not Attempted -The DRB at-
tempts to read the programmed key status and
there are no keys programmmed in the SKIM
memory.
Programming Key Failed -(Possible Used Key
From Wrong Vehicle) - SKIM is unable to program
key due to one of the following:
- faulty ignition key transponder
- ignition key is programmed to another vehicle.
8 Keys Already Learned, Programming Not
Done -SKIM transponder ID memory is full.
1. Obtain ignition keys to be programmed from
customer (8 keys maximum)
2. Using the DRB, erase all ignition keys by select-
ing ``MISCELLANEOUS'' and ``ERASE ALL
CURRENT IGN. KEYS''
3. Program all ignition keys.
Learned Key In Ignition -Ignition key tran-
sponder ID is currently programmed in SKIM mem-
ory.
3.3 DIAGNOSTIC TROUBLE CODES
Each diagnostic trouble code is diagnosed by
following a specific testing procedure. The diagnos-
tic test procedures contain step-by-step instructions
for determining the cause of trouble codes as well as
no trouble code problems. It is not necessary to
perform all of the tests in this book to diagnose an
individual code.
Always begin by reading the diagnostic trouble
codes using the DRBIIIt.
3.3.1 HARD CODE
A diagnostic trouble code that comes back within
one cycle of the ignition key is a ªhardº code. This
means that the defect is there every time the
powertrain control module checks that circuit or
function. Procedures in this manual verify if the
trouble code is a hard code at a the beginning of
each test. When it is not a hard code, an ªintermit-
tentº test must be performed.
Codes that are for Euro Stage III OBD monitors will
not set with just the ignition key on. Comparing these
7
GENERAL INFORMATION
ProCarManuals.com

to non-emission codes, they will seem like an intermit-
tent. These codes require a set of parameters to be
performed (The DRBIIItpre-test screens will help
with this for MONITOR codes), this is called a ªTRIPº.
All EURO STAGE III OBD DTCs will be set after one
or in some cases two trip failures, and the MIL will be
turned on. These codes require three successful (no
failures) TRIPS to extinguish the MIL, followed by 40
warm-up cycles to erase the code.
3.3.2 INTERMITTENT CODE
A diagnostic trouble code that is not there every
time the PCM checks the circuit is an ªintermittentº
code. Most intermittent codes are caused by wiring
or connector problems. Defects that come and go
like this are the most difficult to diagnose; they
must be looked for under specific conditions that
cause them. The following checks may assist you in
identifying a possible intermittent problem:
²Visually inspect related wire harness connectors.
Look for broken, bent, pushed out, or corroded
terminals.
²Visually inspect the related harnesses. Look for
chafed, pierced, or partially broken wire.
²Refer to any Hotline Newsletters or technical
service bulletins that may apply.
²Use the DRBIIItdata recorder or co-pilot.
²Use the DRBIIItPEP module lab scope.
3.3.3 RESET COUNTER
The reset counter counts the number of times the
vehicle has been started since codes were last set,
erased, or the battery was disconnected. The reset
counter will count up to 255 start counts.
The number of starts helps determine when the
trouble code actually happened. This is recorded by
the PCM and can be viewed on the DRBIIItas
STARTS since set.
When there are no trouble codes stored in mem-
ory, the DRBIIItwill display ªNO DTC'S Detectedº
and the reset counter will show ªSTARTS since
clear = XXX.º
3.3.4 HANDLING NO TROUBLE CODE
PROBLEMS
Symptom checks cannot be used properly unless
the driveability problem characteristic actually
happens while the vehicle is being tested.
Select the symptom that most accurately de-
scribes the vehicle's driveability problem and then
perform the test routine that pertains to this symp-
tom. Perform each routine test in sequence until the
problem is found. For definitions, see Section 6.0
Glossary of Terms.SYMPTOM DIAGNOSTIC TEST
HARD START CHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
START AND
STALLCHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
8
GENERAL INFORMATION
ProCarManuals.com

CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
HESITATION/
SAG/
STUMBLECHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING O2S HEATER
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
CHECKING PNP SWITCH
SURGE CHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATIONCHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EVAP EMISSION
SYSTEM
LACK OF
POWER/
SLUGGISHCHECKING THE 5-VOLT
SUPPLY CIRCUIT
CHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EGR SYSTEM
SPARK
KNOCK/
DETONATIONCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
9
GENERAL INFORMATION
ProCarManuals.com

CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EVAP EMISSION
SYSTEM
CUTS OUT/
MISSESCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING EGR SYSTEM
BACKFIRE/
POPBACKCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING THE FUEL
PRESSURE
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING EGR SYSTEM
RUNS
ROUGH/
UNSTABLE/
ERRATIC
IDLECHECKING SECONDARY
IGNITION SYSTEMCHECKING PCM POWER
AND GND CKT
CHECKING ENGINE VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
CHECKING FOR OXYGEN
SENSOR SWITCHING
CHECKING O2S HEATER
CHECKING IDLE AIR CON-
TROL MOTOR OPERATION
CHECKING ENGINE ME-
CHANICAL SYSTEMS
CHECKING EVAP EMISSION
SYSTEM
CHECKING EGR SYSTEM
CHECKING IAT SENSOR
CHECKING PNP SWITCH
POOR FUEL
ECONOMYCHECKING SECONDARY
IGNITION SYSTEM
CHECKING PCM POWER
AND GND CKT
CHECKING ENGING VAC-
UUM
CHECKING THE FUEL
PRESSURE
CHECKING COOLANT SEN-
SOR CALIBRATION
CHECKING THROTTLE PO-
SITION SENSOR CALIBRA-
TION
CHECKING MAP SENSOR
CALIBRATION
CHECKING THE MINIMUM
IDLE AIR FLOW
10
GENERAL INFORMATION
ProCarManuals.com

applicable. These procedures can be found in ser-
vice manual procedures. Following these proce-
dures is very important to the safety of individuals
performing diagnostic tests.
4.2.2 VEHICLE PREPARATION FOR
TESTING
Make sure the vehicle being tested has a fully
charged battery. If it does not, false diagnostic codes
or error messages may occur.
4.2.3 SERVICING SUB-ASSEMBLIES
Some components of the powertrain system are
intended to be serviced in assembly only. Attempt-
ing to remove or repair certain system sub-
components may result in personal injury and/or
improper system operation. Only those components
with approved repair and installation procedures in
the service manual should be serviced.
4.2.4 DRBIIITSAFETY INFORMATION
WARNING: EXCEEDING THE LIMITS OF THE
DRB MULTIMETER IS DANGEROUS. IT CAN
EXPOSE YOU TO SERIOUS INJURY.
CAREFULLY READ AND UNDERSTAND THE
CAUTIONS AND THE SPECIFICATION
LIMITS.
Follow the vehicle manufacturer 's service specifi-
cations at all times.
²Do not use the DRBIIItif it has been damaged.
²Do not use the test leads if the insulation is
damaged or if metal is exposed.
²To avoid electrical shock, do not touch the test
leads, tips or the circuit being tested.
²Choose the proper range and function for the
measurement. Do not try voltage or current mea-
surements that may exceed the rated capacity.
²Do not exceed the limits shown in the table below:
FUNCTION INPUT LIMIT
Volts 0 - 500 peak volts AC
0 - 500 volts DC
Ohms (resistance)* 0 -1.12 megohms
Frequency Measured
Frequency Generated0-10kHz
Temperature -58 - 1100ÉF
-50 - 600ÉC
* Ohms cannot be measured if voltage is present.
Ohms can be measured only in a non-powered
circuit.
²Voltage between any terminal and ground must
not exceed 500v DC or 500v peak AC.
²Use caution when measuring voltage above 25v
DC or 25v AC.
²The circuit being tested must be protected by a
10A fuse or circuit breaker.
²Use the low current shunt to measure circuits up
to 10A. Use the high current clamp to measure
circuits exceeding 10A.
²When testing for the presence of voltage or cur-
rent, make sure the meter is functioning cor-
rectly. Take a reading of a known voltage or
current before accepting a zero reading.
²When measuring current, connect the meter in
series with the load.
²Disconnect the live test lead before disconnecting
the common test lead.
²When using the meter function, keep the DRB
away from spark plug or coil wires to avoid
measuring error from outside interference.
4.3 WARNINGS AND CAUTIONS
4.3.1 ROAD TEST WARNINGS
Some complaints will require a test drive as part
of the repair verification procedure. The purpose of
the test drive is to try to duplicate the diagnostic
code or symptom condition.
CAUTION: BEFORE ROAD TESTING A
VEHICLE, BE SURE THAT ALL
COMPONENTS ARE REASSEMBLED.
DURING THE TEST DRIVE, DO NOT TRY TO
READ THE DRB SCREEN WHILE IN MOTION.
DO NOT HANG THE DRB FROM THE REAR
VIEW MIRROR OR OPERATE IT YOURSELF.
HAVE AN ASSISTANT AVAILABLE TO
OPERATE THE DRB.
4.3.2 VEHICLE DAMAGE CAUTIONS
Before disconnecting any control module, make
sure the ignition is ªoffº. Failure to do so could
damage the module.
When testing voltage or continuity at any control
module, use the terminal side (not the wire end) of
the connector. Do not probe a wire through the
insulation; this will damage it and eventually cause
it to fail because of corrosion.
Be careful when performing electrical tests so as
to prevent accidental shorting of terminals. Such
mistakes can damage fuses or components. Also, a
second code could be set, making diagnosis of the
original problem more difficult.
12
GENERAL INFORMATION
ProCarManuals.com

Symptom:
P-0622 GENERATOR FIELD NOT SWITCHING PROPERLY
When Monitored and Set Condition:
P-0622 GENERATOR FIELD NOT SWITCHING PROPERLY
When Monitored: With the ignition key on and the engine not running.
Set Condition: This trouble code sets when the PCM tries to regulate the generator field
with no result during monitoring.
POSSIBLE CAUSES
GENERATOR FIELD RESISTANCE > = 5.0 OHMS
ASD WIRING HARNESS INTERMITTENT DEFECT
ASD WIRING HARNESS OBSERVABLE DEFECT
GENERATOR FIELD DRIVE CIRCUIT SHORT TO GROUND
GENERATOR FIELD DRIVER CIRCUIT OPEN
PCM DEFECTIVE (GENERATOR)
ASD RELAY OUTPUT CIRCUIT OPEN
TEST ACTION APPLICABILITY
1 Ignition On, Engine Not Running.
With the DRB, actuate the Generator Field Driver Circuit.
Backprobe the ASD Relay Output Circuit at the back of the Generator.
Is the voltage above 10.0 volts?All
Ye s®Go To 2
No®Repair the open ASD Relay Output Circuit, Generator to Harness
Splice.
2 Engine Running
With the DRB, actuate the Generator Field Driver Circuit.
Backprobe the Generator Field Driver Circuit at the back of the Generator.
Does the voltage shift from low to high?All
Ye s®Go To 3
No®Go To 5
3 Ignition On, Engine Not Running.
With the DRB, actuate the Generator Field Driver Circuit.
With the DRB, read codes.
Wiggle Wiring Harness from the Generator to PCM.
Does the Generator Field Driver Circuit code return?All
Ye s®Repair as necessary where wiggling caused problem to appear.
Perform Powertrain Verification Test VER-3A.
No®Go To 4
16
CHARGING
ProCarManuals.com

TEST ACTION APPLICABILITY
4 Ignition Off.
Using the schematic as a guide, inspect the Wiring and Connectors.
Were any problems found?All
Ye s®Repair as necessary.
Perform Powertrain Verification Test VER-3A.
No®Test Complete.
5 Ignition Off
Disconnect the PCM.
Disconnect the Generator Field Harness Connector at back of the Generator.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, test resistance across the Generator Field Terminals.
Is the resistance below 5.0 ohms?All
Ye s®Go To 6
No®Repair the Generator as necessary.
Perform Powertrain Verification Test VER-3A.
6 Ignition Off
Disconnect the PCM.
Disconnect the Generator Field Harness Connector at back of the Generator.
Note: Check connectors - Clean/repair as necessary.
Using an Ohmmeter, measure the resistance of Generator Field Driver Circuit from
the at Generator Harness Connector to ground.
Is the resistance below 5.0 ohms?All
Ye s®Repair the Generator Field Driver Circuit short to ground.
Perform Powertrain Verification Test VER-3A.
No®Go To 7
7 Ignition Off
Disconnect the PCM.
Disconnect the Generator Field Harness Connector at back of the Generator.
Note: Check connectors - Clean/repair as necessary.
Using an ohmmeter, test the resistance of the Generator Field Driver Circuit
Generator Connector to PCM Connector.
Is the resistance below 5.0 ohms?All
Ye s®Go To 8
No®Repair open Generator Field Driver Circuit Generator to PCM.
Perform Powertrain Verification Test VER-3A.
8 Ignition Off
If there are no potential causes remaining, the PCM is assumed to be defective.
View repair options.All
Repair
Replace the PCM.
Perform Powertrain Verification Test VER-3A.
17
CHARGING
P-0622 GENERATOR FIELD NOT SWITCHING PROPERLY ÐContinued
ProCarManuals.com