2000 CHRYSLER CARAVAN ignition

TEST TC-6AREPAIRING - A/C SYSTEM PRESSURE SUPPLY LOW EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION ON. DOES THE DRB
START TEST WITH THE DRB, DISPLAY "A/C YES CONTINUE TEST
TC-6A. ERASE CODES. SYSTEM PRESSURE TC-6A ON THE
SUPPLY LOW NEXT PAGE.
TURN A/C ON. EXCEEDED"?
NO
WIGGLE THE A/C DOES THE DRB REPAIR THE
PRESSURE SENSOR MONITOR THE DRB DISPLAY "A/C YES CONNECTOR OR
CONNECTOR AND DISPLAY. SYSTEM PRESSURE HARNESS WIRES THAT
HARNESS WIRES. SUPPLY LOW CAUSED THE CODE TO
EXCEEDED"? SET.*
NO
AT THIS TIME THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THIS CODE GUIDE, INSPECT THE FOUND? NECESSARY.*
IS NOT PRESENT. WIRING AND
CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES. FIG.1
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
47
ProCarManuals.com

TEST TC-6ACONTINUED - REPAIRING - A/C SYSTEM PRESSURE SUPPLY LOW EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-6A KEY OFF.
CONTINUED FROM DISCONNECT THE A/C
THE PREVIOUS PRESSURE SENSOR
PAGE. HARNESS
CONNECTOR.**
WITH THE DRB, IS THE A/C
MONITOR THE A/C PRESSURE SUPPLY YES REPLACE THE A/C
TURN IGNITION ON. PRESSURE SENSOR VOLTAGE ABOVE 4.0 PRESSURE SENSOR.*
SUPPLY VOLTAGE. VOLTS?
NO
KEY OFF.
DISCONNECT THE ECM USE AN OHMMETER IN
HARNESS THE FOLLOWING
CONNECTORS.** STEPS.
MEASURE THE A/C REPAIR THE A/C
PRESSURE SENSOR IS THE RESISTANCE YES PRESSURE SENSOR
5-VOLT SUPPLY BELOW 5.0 OHMS? SUPPLY CIRCUIT FOR
CIRCUIT TO GROUND. A SHORT TO
FIG.1 GROUND.*
NO
MEASURE THE A/C REPAIR THE A/C
PRESSURE SENSOR IS THE RESISTANCE YES PRESSURE SENSOR
5-VOLT SUPPLY CKT BELOW 5.0 OHMS? SUPPLY CIRCUIT FOR
TO SENSOR GROUND. A SHORT TO SENSOR
FIG.1 GROUND.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
49
ProCarManuals.com

TEST TC-7BREPAIRING - ACCELERATOR PEDAL SENSOR TROUBLE CODES
Perform TEST TC-7A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH JUMPER STILL DOES THE DRB DISPLAY REPAIR THE OPEN
START TEST CONNECTED TO CAVITY CHANGE BETWEEN YES SENSOR GROUND.
TC-7B. 5, TAP THE OTHER END "IDLE" TO "ABOVE IF OK,
OF THE JUMPER TO IDLE" WHEN TAPPING REPLACE THE ECM*
CHASSIS GROUND. THE JUMPER WIRE?
NO
USING A VOLTMETER, REPAIR THE LOW
MEASURE THE LOW IS THE VOLTAGE YES IDLE POSITION
IDLE POSITION ABOVE 5.5 VOLTS? SENSE CIRCUIT FOR
SENSE CKT. A SHORT TO
FIG.1 VOLTAGE.*
NO
TURN IGNITION OFF. USING AN OHMMETER, REPAIR THE LOW
MEASURE BETWEEN IS THE RESISTANCE YES IDLE POSITION
DISCONNECT THE ECM GROUND AND THE LOW BELOW 5.0 OHMS? SENSE CIRCUIT FOR
HARNESS IDLE POSITION A SHORT TO
CONNECTORS.** SENSE CKT. FIG.1 GROUND.*
NO
USING AN OHMMETER,
MEASURE THE LOW IS THE RESISTANCE NO REPAIR THE OPEN
IDLE POSITION BELOW 5.0 OHMS? LOW IDLE POSITION
SENSE CKT. SENSE CIRCUIT.*
FIG.2
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
57
ProCarManuals.com

TEST TC-7CREPAIRING - ACCELERATOR PEDAL SENSOR TROUBLE CODES
Perform TEST TC-7A Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST DISCONNECT THE ECM
TC-7C. TURN IGNITION OFF. HARNESS
CONNECTORS.**
MEASURE BETWEEN REPAIR THE 5-VOLT
USE AN OHMMETER IN GROUND AND THE IS THE RESISTANCE YES SUPPLY CIRCUIT FOR
THE FOLLOWING 5-VOLT SUPPLY CKT. BELOW 5.0 OHMS? A SHORT TO
STEPS. GROUND.*
FIG.1
NO
EACH GROUND CIRCUIT REPAIR THE 5-VOLT
MEASURE BETWEEN AT ACCEL PEDAL IS THE RESISTANCE YES SUPPLY CIRCUIT FOR
THE 5-VOLT SUPPLY SENSOR HARNESS CONN BELOW 5.0 OHMS? A SHORT TO SENSOR
CIRCUIT AND... CAVITIES 3 AND 8. GROUND.*
FIG.1
NO
WITH A JUMPER WIRE,
REMOVE THE DIESEL CONNECT DIESEL POWER
POWER RELAY.** RELAY CONN. CAVITIES
30 AND 87 (IN PDC).
FIG.2
USING A VOLTMETER, REPAIR THE 5-VOLT
MEASURE THE 5-VOLT IS THE VOLTAGE YES SUPPLY CIRCUIT FOR
TURN IGNITION ON. SUPPLY CKT. ABOVE 1.0 VOLT? A SHORT TO
VOLTAGE.*
FIG.1
NO
USING AN OHMMETER,
MEASURE THE IS THE RESISTANCE NO REPAIR THE OPEN
TURN IGNITION OFF. RESISTANCE OF THE BELOW 5.0 OHMS? 5-VOLT SUPPLY
5-VOLT SUPPLY CKT. CIRCUIT.*
FIG.3
YES
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
59
ProCarManuals.com

TEST TC-15AREPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL HIGH EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION ON.
START TEST WITH THE DRB, READ IS THE VOLTAGE YES CONTINUE TEST
TC-15A. THE BOOST PRESSURE ABOVE 4.5 VOLTS? TC-15A ON THE
SENSOR VOLTAGE. NEXT PAGE.
NO
USE THE SCHEMATIC AS REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB WAS THERE ANY YES OR CONNECTOR THAT
BOOST PRESSURE DISPLAY. BOOST PRESSURE CAUSED THE VOLTAGE
SENSOR CONNECTOR AND VOLTAGE CHANGE? CHANGE.*
HARNESS. FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION TO SET SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
THE CODE IS NOT GUIDE, INSPECT THE FOUND? NECESSARY.*
PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2
FOR ADDITIONAL TEST COMPLETE.
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
63
ProCarManuals.com

TEST TC-15ACONTINUED - REPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-15A
CONTINUED FROM DISCONNECT THE
THE PREVIOUS PRESSURE
PAGE. SENSOR
KEY ON. USING A THE BOOST PRESSURE
VOLTMETER, MEASURE SENSOR 5-VOLT IS THE VOLTAGE NO CONTINUE TEST
THE VOLTAGE SUPPLY CIRCUIT AND ABOVE 5.2 VOLTS? TC-15A ON THE
BETWEEN... GROUND. NEXT PAGE.
FIG.1
YES
KEY OFF.
DISCONNECT THE ECM REMOVE THE DIESEL
HARNESS POWER RELAY.**
CONNECTORS.**
WITH A JUMPER WIRE, TURN IGNITION ON.
CONNECT DIESEL POWER
RELAY CONN. CAVITIES USE A VOLTMETER IN
30 AND 87 (IN PDC). THE FOLLOWING
FIG.1 STEP.
MEASURE THE 5-VOLT
SUPPLY CKT AT THE IS THE VOLTAGE YES REPAIR THE 5-VOLT
BOOST PRESSURE ABOVE 1.0 VOLT? SUPPLY CKT FOR A
SENSOR HARNESS SHORT TO VOLTAGE.*
CONNECTOR. FIG.2
NO
REPLACE THE ENGINE
CONTROL MODULE.* TURN IGNITION OFF.
BOOST
HARNESS
CONNECTOR.**
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
65
ProCarManuals.com

TEST TC-15ACONTINUED - REPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-15A
CONTINUED FROM IS THE VOLTAGE NO CONTINUE TEST
THE PREVIOUS ABOVE 1.0 VOLT? TC-15A ON THE
PAGE.NEXT PAGE.
YES
KEY OFF.
DISCONNECT THE ECM REMOVE THE DIESEL
HARNESS POWER RELAY.**
CONNECTORS.**
WITH A JUMPER WIRE, TURN IGNITION ON.
CONNECT DIESEL POWER
RELAY CONN. CAVITIES USE A VOLTMETER IN
30 AND 87 (IN PDC). THE FOLLOWING
FIG.1 STEP.
MEASURE THE BOOST REPAIR THE BOOST
PRESSURE SENSOR IS THE VOLTAGE YES PRESSURE SENSOR
SIGNAL CIRCUIT. ABOVE 1.0 VOLT? SIGNAL CIRCUIT FOR
A SHORT TO
FIG.2 VOLTAGE.
NO
REPLACE THE ENGINE
CONTROL MODULE.* WITH A VOLTMETER,
MEASURE THE BOOST
PRESSURE SENSOR
SIGNAL CKT.
FIG.1
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
67
ProCarManuals.com

TEST TC-16AREPAIRING - TURBOCHARGER BOOST SENSOR SIGNAL LOW EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION ON. IS THE BOOST
START TEST WITH THE DRB, READ PRESSURE SENSOR YES CONTINUE TEST
TC-16A. THE BOOST PRESSURE VOLTAGE BELOW 0.2 TC-16A ON THE
SENSOR VOLTAGE. VOLT? NEXT PAGE.
NO
USE THE SCHEMATIC AS WAS THERE ANY REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB BOOST PRESSURE YES OR CONNECTOR THAT
BOOST PRESSURE DISPLAY. SENSOR VOLTAGE CAUSED THE VOLTAGE
SENSOR CONNECTOR & CHANGE? CHANGE.*
HARNESS. FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
71
ProCarManuals.com