2000 CHRYSLER CARAVAN engine

TEST TC-62ACONTINUED - REPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-62A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS BOOST PRESSURE
PAGE. SENSOR HARNESS
CONNECTOR.**
WITH A JUMPER WIRE, TURN IGNITION ON.
DISCONNECT THE ECM REMOVE THE DIESEL CONNECT DIESEL POWER
HARNESS POWER RELAY.** RELAY CONN. CAVITIES USE A VOLTMETER IN
CONNECTORS.** 30 AND 87 (IN PDC). THE FOLLOWING
FIG.1 STEP.
MEASURE THE IAT REPAIR THE INTAKE
SENSOR SIGNAL IS THE VOLTAGE YES AIR TEMPERATURE
CIRCUIT. ABOVE 1.0 VOLT? SENSOR SIGNAL
CIRCUIT FOR A
FIG.2 SHORT TO VOLTAGE.*
NO
KEY OFF. USING AN OHMMETER, REPAIR THE OPEN
MEASURE THE IAT IS THE RESISTANCE NO INTAKE AIR
REMOVE THE JUMPER SENSOR SIGNAL BELOW 5.0 OHMS? TEMPERATURE SENSOR
WIRE. CIRCUIT. SIGNAL CIRCUIT.*
FIG.3
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN THE INTAKE WITH THE DRB, DISPLAY "INTAKE YES REPLACE THE BOOST
AIR TEMP SENSOR ERASE AND THEN AIR TEMPERATURE PRESSURE SENSOR.*
SIGNAL AND SENSOR READ CODES. SENSOR LOW
GROUND CKT. FIG.1 EXCEEDED"?
NO
MOVE THE JUMPER DOES THE DRB
WIRE FROM THE WITH THE DRB, READ DISPLAY "INTAKE YES REPAIR THE OPEN
SENSOR GROUND TO CODES. AIR TEMPERATURE SENSOR GROUND
AN ENGINE GROUND. SENSOR LOW CIRCUIT.*
EXCEEDED"?
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
219
ProCarManuals.com

TEST TC-72ACONTINUED - REPAIRING - NEEDLE MOVEMENT SENSOR SRC HIGH EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-72A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS NEEDLE MOVEMENT
PAGE. SENSOR HARNESS
CONNECTOR.**
CONNECT A JUMPER DOES THE DRB
BETWEEN THE NEEDLE WITH THE DRB, READ DISPLAY "NEEDLE YES REPLACE THE NEEDLE
SENSOR SIGNAL AND CODES. MOVEMENT SENSOR MOVEMENT SENSOR.*
SENSOR GROUND CKT. SRC LOW EXCEEDED"?
FIG.1
NO
MOVE THE JUMPER DOES THE DRB
WIRE FROM THE WITH THE DRB, READ DISPLAY "NEEDLE YES REPAIR THE OPEN
SENSOR GROUND TO CODES. MOVEMENT SENSOR SENSOR GROUND
AN ENGINE GROUND. SRC LOW EXCEEDED"? CIRCUIT.*
NO
KEY OFF. WITH A JUMPER WIRE,
DISCONNECT THE ECM REMOVE THE DIESEL CONNECT DIESEL POWER
HARNESS POWER RELAY. RELAY CONN. CAVITIES
CONNECTORS.** 30 AND 87 (IN PDC).
FIG.2
KEY ON. MEASURE REPAIR THE SHORT
USE A VOLTMETER IN THE NEEDLE IS THE VOLTAGE YES TO VOLTAGE ON THE
THE FOLLOWING MOVEMENT SENSOR ABOVE 0.5 VOLT? NEEDLE MOVEMENT
STEP. SIGNAL CIRCUIT. SENSOR SIGNAL
FIG.1 CIRCUIT.*
NO
KEY OFF. MEASURE THE NEEDLE
MOVEMENT SENSOR IS THE RESISTANCE YES REPLACE THE ENGINE
USE AN OHMMETER IN SIGNAL CIRCUIT. BELOW 5.0 OHMS? CONTROL MODULE.*
THE FOLLOWING
STEP. FIG.3
NO
REPAIR THE OPEN
NEEDLE MOVEMENT
SENSOR SIGNAL
CIRCUIT.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
227
ProCarManuals.com

TEST TC-73ACONTINUED - REPAIRING - NEEDLE MOVEMENT SENSOR SRC LOW EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-73A DOES THE DRB
CONTINUED FROM DISCONNECT THE DISPLAY "NEEDLE YES REPLACE THE NEEDLE
THE PREVIOUS NEEDLE MOVEMENT MOVEMENT SENSOR MOVEMENT SENSOR.*
PAGE. SENSOR.** SRC HIGH
EXCEEDED"?
NO
KEY OFF. USING AN OHMMETER, REPAIR THE NEEDLE
DISCONNECT THE ECM MEASURE THE NEEDLE IS THE RESISTANCE YES MOVEMENT SENSOR
HARNESS MOVEMENT SENSOR BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
CONNECTORS.** SIGNAL CIRCUIT TO A SHORT TO
GROUND. FIG.1 GROUND.*
NO
WITH AN OHMMETER NEEDLE MOVEMENT REPAIR THE NEEDLE
MEASURE THE SENSOR SIGNAL IS THE RESISTANCE YES MOVEMENT SENSOR
RESISTANCE BETWEEN CIRCUIT AND SENSOR BELOW 5.0 OHMS? SIGNAL CIRCUIT
THE... GROUND CIRCUIT. SHORTED TO THE
FIG.1 SENSOR GND CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
231
ProCarManuals.com

TEST TC-74AREPAIRING - REDUNDANT EMERGENCY STOP PLAUSIBILITY IN AFTER-RUN
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TURN IGNITION ON,
ENGINE OFF. USING
THE DRB READ ECM
CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
233
ProCarManuals.com

TEST TC-74ACONTINUED - REPAIRING - EMERGENCY STOP PLAUSIBILITY IN AFTER-RUN
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-74A KEY OFF.
CONTINUED FROM DISCONNECT THE REMOVE THE DIESEL
THE PREVIOUS FUEL PUMP AND ECM POWER RELAY.**
PAGE. HARNESS
CONNECTORS.**
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE FUEL
CONNECT DIESEL POWER VOLTMETER, MEASURE IS THE VOLTAGE YES SHUTDOWN SOLENOID
RELAY CONN. CAVITIES THE FUEL SHUTDOWN ABOVE 1.0 VOLT? CONTROL CIRCUIT
30 AND 87 (IN PDC). SOL CONTROL CKT. FOR A SHORT TO
FIG.1 FIG.2 VOLTAGE.*
NO
RECONNECT THE
ENGINE CONTROL KEY ON. USING DRB
MODULE HARNESS ACTUATE THE "FUEL
CONNECTORS. SHUT-OFF SOL."
WITH THE DRB FUEL PUMP HARNESS DOES VOLTMETER
ACTUATING THE CONNECTOR CAVITY 6. CHANGE FROM YES REPLACE FUEL PUMP
SOLENOID, USE A BATTERY VOLTAGE TO ASSEMBLY.*
VOLTMETER TO BELOW 1.0 VOLT?
PROBE... FIG.2
NO
NOTE: BEFORE
REPLACING ECM, DID THE FUEL YES REPLACE THE ENGINE
PERFORM TEST NTC-3A INJECTION PUMP CONTROL MODULE.*
TO CHECK INTERNAL PASS TEST NTC-3A?
FUEL PUMP CIRCUITRY.
NO
REPLACE THE FUEL
INJECTION PUMP
ASSEMBLY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
235
ProCarManuals.com

TEST TC-75AREPAIRING - REDUNDANT EMERGENCY STOP POWERSTAGE DEFECTIVE
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB,
TC-75A. ERASE CODES.
CYCLE THE IGNITION DOES THE DRB
ON AND OFF SEVERAL WITH THE IGNITION DISPLAY "REDUNDANT YES CONTINUE TEST
TIMES, PAUSING FOR ON ENGINE OFF, EMERG STOP TC-75A ON THE
TEN SECONDS AT KEY READ CODES. POWERSTAGE NEXT PAGE.
ON AND OFF. DEFECTIVE"?
NO
AT THIS TIME THE REVIEW THE CIRCUIT
CONDITION FOR DESCRIPTION FOR A WERE ANY PROBLEMS YES REPAIR AS
SETTING THE CODE PROPER UNDERSTANDING FOUND? NECESSARY.*
IS NOT PRESENT. OF THIS CODE. CHECK
FIG.1 FOR PROBLEMS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
237
ProCarManuals.com

TEST TC-75ACONTINUED - REPAIRING - REDUNDANT EMERGENCY STOP POWERSTAGE
DEFECTIVE
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-75A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS FUEL PUMP AND ECM
PAGE. HARNESS
CONNECTORS.**
MEASURE THE
USE AN OHMMETER IN RESISTANCE OF THE IS THE RESISTANCE NO REPAIR OPEN FUEL
THE FOLLOWING FUEL SHUTDOWN BELOW 5.0 OHMS? SHUTDOWN SOLENOID
STEPS. SOLENOID CONTROL CONTROL CIRCUIT.*
CIRCUIT. FIG.1
YES
MEASURE THEREPAIR THE FUEL
RESISTANCE OF THE IS THE RESISTANCE YES SHUTDOWN SOLENOID
FUEL SHUTDOWN SOL. BELOW 5.0 OHMS? CIRCUIT FOR A
CONTROL CIRCUIT TO SHORT TO GROUND.*
GROUND. FIG.2
NO
RECONNECT THE
ENGINE CONTROL KEY ON. USING DRB
MODULE HARNESS ACTUATE THE "FUEL
CONNECTORS. SHUT-OFF SOL."
WITH THE DRB FUEL PUMP HARNESS DOES VOLTMETER
ACTUATING THE CONNECTOR CAVITY 6. CHANGE FROM YES REPLACE FUEL PUMP
SOLENOID, USE A BATTERY VOLTAGE TO ASSEMBLY.*
VOLTMETER TO BELOW 1.0 VOLT?
PROBE... FIG.2
NO
NOTE: BEFORE
REPLACING ECM, DID FUEL INJECTION YES REPLACE THE ENGINE
PERFORM TEST NTC-3A PUMP PASS TEST CONTROL MODULE.*
TO CHECK INTERNAL NTC-3A?
FUEL PUMP CIRCUITRY.
NO
REPLACE THE FUEL
INJECTION PUMP
ASSEMBLY.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
239
ProCarManuals.com

TEST TC-76AREPAIRING - SMART START RELAY SHORT CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-1A. **Check connectors - Clean / repair as necessary.
REPLACE THE
START TEST STARTER RELAY WITH
TC-76A. A KNOWN GOOD
RELAY.
FIG.1
FULLY DEPRESS THE
CLUTCH PEDAL AND DOES THE ENGINE YES REPLACE THE
ATTEMPT TO CRANK CRANK? INITIAL STARTER
THE ENGINE RELAY.
NO
KEY OFF.
REMOVE THE STARTER REMOVE THE DIESEL
DISCONNECT THE ECM RELAY.** POWER RELAY.**
HARNESS
CONNECTORS.**
WITH A JUMPER WIRE, KEY ON. USING A REPAIR THE STARTER
CONNECT DIESEL POWER TEST LIGHT, PROBE IS THE TEST LIGHT YES RELAY CONTROL
RELAY CONN. CAVITIES THE STARTER RELAY ON? CIRCUIT FOR A
30 AND 87 (IN PDC). CONTROL CIRCUIT. SHORT TO VOLTAGE.*
FIG.1 FIG.1
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
241
ProCarManuals.com