2000 CHEVROLET MONTE CARLO display

2-14

Horn Chirp On Timer (Available with Remote
Keyless Entry)

Remote Keyless Entry Transmitter Programming
(Available with Remote Keyless Entry)

Return to Original Factory Settings
(Available for All)

Exit Vehicle Customization Mode
To reset or customize your vehicle's features, you must
first enter the vehicle customization main menu. To
enter the main menu:
1. Turn the ignition to ACC or ON and the radio off.
2. Press and hold the DISP button on the radio for at
least five seconds until SETTINGS is displayed.
3. Press the SEEK up or down arrows to scroll through
each available feature on your main menu.
4. Press the PREV or NEXT buttons to scroll through
the lower menu. An asterisk will appear next to the
item that is the current setting.The following information shows how to reset or
customize features after entering the main menu:
SETTINGS
- Display Current Settings
OIL LIFE
- Oil Life Reset: This feature allows you to
reset the engine oil life monitor after an oil change, see
ªEngine Oilº in the Index. Be careful not to reset the
OIL LIFE accidentally at any time other than when the
oil has been changed. It can't be reset accurately until
the next oil change. To clear the CHANGE ENGINE
OIL light from the instrument cluster and reset the oil
life monitor:
1. Scroll, using the SEEK up or down arrows, until OIL
LIFE appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. RESET will then be displayed.
3. Press the DISP button to reset. A chime will be heard
to verify the new setting and DONE will be
displayed for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-15
TIRE MON (Tire Inflation Monitor Reset): This feature
allows you to reset the tire pressure monitor after
checking all tire pressures, see ªTiresº in the Index.
To clear the LOW TIRE PRESSURE light from the
instrument cluster and reset the tire inflation monitor:
1. Scroll, using the SEEK up or down arrows, until
TIRE MON appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. RESET will be displayed.
3. Press the DISP button to reset. A chime will be heard
to verify the new setting and DONE will be
displayed for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.LT DELAY (Delayed Headlamp Illumination):
This feature allows the vehicle's headlamps and
parking lamps to stay on for a fixed amount of time
after you exit the vehicle. To customize delayed
headlamp illumination:
1. Scroll, using the SEEK up or down arrows, until
LT DELAY appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll, using the PREV or NEXT buttons,
through the following options:

OFF
- Turns feature off.

30 SEC
- 30 seconds.

60 SEC
- 60 seconds.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-16
AUTOLOCK (Automatic Door Lock and Unlock): With
the ignition in ON and the vehicle's doors closed, this
feature allows the vehicle doors to automatically lock
and unlock when the driver shifts the vehicle's transaxle
into and out of PARK (P). To customize the automatic
door lock and unlock:
1. Scroll, using the SEEK up or down arrows, until
AUTOLOCK appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

OFF
- Turns feature off.

LCK ONLY
- Automatic door lock on/automatic
door unlock off.

DRVR UNL
- Automatic door lock on/automatic
door unlock on (driver's door only).

ALL UNL
- Automatic door lock on/automatic
door unlock on.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.FOB LIGHT (Remote Visual Verification): This feature
allows the exterior lights to flash when the remote
keyless entry transmitter is used to lock or unlock the
vehicle. To customize remote visual verification:
1. Scroll, using the SEEK up or down arrows, until
FOB LIGHT appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

OFF
- Turns feature off.

ON
- One flash for each remote lock/two flashes
for each remote unlock.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. A new selection will be displayed with
an asterisk for one second.
If your vehicle is equipped with the content
theft
-deterrent system, the first time a remote UNLOCK
command is received, three flashes will be seen and
three horn chirps heard to indicate an alarm condition
has occurred since last arming. See ªContent
Theft
-Deterrent Systemº in the Index.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-17
FOB HORN (Remote Audible Verification): This
feature allows the horn to chirp when the remote keyless
entry transmitter (if equipped) is used to lock or unlock
the vehicle. To customize remote audible verification:
1. Scroll, using the SEEK up or down arrows, until
FOB HORN appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

OFF
- Turns feature off.

PARTIAL
- One chirp for each remote LOCK
command/no chirp for remote UNLOCK command.

FULL
- One chirp for each remote LOCK
command/two chirps for the first remote
UNLOCK command.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
If your vehicle is equipped with the content
theft
-deterrent system, the first time the remote
UNLOCK command is received three chirps will be
heard to indicate an alarm condition has occurred since
last arming. See ªContent Theft
-Deterrent Systemº in
the Index.The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
ALARM (Content Theft Operation): This feature allows
the content theft
-deterrent system to be turned on or off.
To customize the content theft
-deterrent system:
1. Scroll, using the SEEK up or down arrows, until
ALARM appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

ALRM OFF
- Turns feature off.

ALRM ON
- Turns feature on.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-18
TRNKJAMB (Trunk Jamb): This feature allows the
content theft system trunk lock sensor to be disabled or
enabled. To customize the trunk lock sensor:
1. Scroll, using the SEEK up or down arrows, until
TRNKJAMB appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

TRNK OFF
- Turns feature off.

TRNK ON
- Turns feature on.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.CHIRP (Horn Chirp Timer): This feature allows you to
choose between short or long horn chirp sounds when
the remote keyless entry transmitter is used.
To customize the length of horn chirps:
1. Scroll, using the SEEK up or down arrows, until
CHIRP appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. Scroll through the following options:

SHORT - Short Chirp (16 msec)

LONG
- Long Chirp (32 msec)
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.

2-19
ORIG. SET (Return to the Original Settings): This
feature allows you to return all feature customization
settings back to their original factory settings. To reset:
1. Scroll, using the SEEK up or down arrows, until
ORIG. SET appears on the display.
2. Press the PREV or NEXT button to enter the
submenu. SET ALL will appear.
3. With your preference displayed, press the DISP
button to select. A chime will be heard to verify the
new setting. The new selection will be displayed
with an asterisk for one second.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
FOB PROG (Remote Keyless Entry Transmitter
Programming): This feature allows you to match the
remote keyless entry transmitter to your vehicle.
To match the transmitter:
1. Scroll, using the SEEK up or down arrows, until
FOB PROG appears on the display.2. Press the PREV or NEXT button to enter the
submenu. The current selection will have an asterisk
next to it. BEGIN will be displayed.
3. Press the DISP button to start programming. When
the message PUSH FOB flashes, press and hold the
LOCK and UNLOCK buttons on the first transmitter
at the same time for 15 seconds. A chime will be
heard to verify the transmitter is learned.
4. Repeat Step 3 for each additional transmitter.
The mode you selected is now set. You can either exit
the programming mode by following the instructions
later in this section or program the next feature available
on your vehicle.
EXIT (Exit Feature Customization Mode): This feature
allows you to exit the vehicle customization
programming. To exit:

Scroll until EXIT appears on the display.

Press the DISP button to exit programming. A chime
will be heard to verify the exit.

2-20
Passlock

Your vehicle is equipped with the Passlock
theft
-deterrent system.
Passlock is a passive theft
-deterrent system. Passlock
enables fuel if the ignition lock cylinder is turned with a
valid key. If a correct key is not used or the ignition lock
cylinder is tampered with, fuel is disabled and the
engine will not start.
During normal operation, the SECURITY message
will be displayed after the key is turned to the ON
ignition position.
If the engine stalls and the SECURITY message flashes,
wait until the light stops flashing before trying to restart
the engine.
If the engine is running and the SECURITY message
comes on, you will be able to restart the engine if you turn
the engine off. However, your Passlock system is not
working properly and must be serviced by your dealer.
Your vehicle is not protected by Passlock at this time. You
may also want to check the fuse (see ªFuses and Circuit
Breakersº in the Index). See your dealer for service.
In an emergency, call the Chevrolet Roadside Assistance
Center at 1
-800-CHEV-USA
(1-800-243-8872).
(In Canada, call 1
-800-268-6800.)
New Vehicle ªBreak-Inº
NOTICE:
Your vehicle doesn't need an elaborate
ªbreak
-in.º But it will perform better in the
long run if you follow these guidelines:

Don't drive at any one speed -- fast or
slow
-- for the first 500 miles (805 km).
Don't make full
-throttle starts.

Avoid making hard stops for the first
200 miles (322 km) or so. During this time
your new brake linings aren't yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking
-in guideline every
time you get new brake linings.

Don't tow a trailer during break
-in.
See ªTowing a Trailerº in the Index for
more information.

2-22
ON: This is the position to which the switch returns
after you start the engine and release the switch. The
switch stays in ON when the engine is running. But
even when the engine is not running, you can use ON
to operate your electrical power accessories and to
display some instrument panel cluster messages and
warning lights.
START: This position starts the engine. When the
engine starts, release the key. The ignition switch will
return to ON for normal driving.
When the engine is not running, ACC and ON allow you
to operate your electrical accessories, such as the radio.
A warning chime will sound if you open the driver's
door when the ignition is in OFF or ACC and the key is
in the ignition.Retained Accessory Power (RAP)
With retained accessory power (RAP), your power
windows, audio system and the optional sunroof will
continue to work up to 10 minutes after the ignition key
is turned to OFF and no door is opened.
Starting Your Engine
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's a
safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
NOTICE:
Don't try to shift to PARK (P) if your vehicle is
moving. If you do, you could damage the
transaxle. Shift to PARK (P) only when your
vehicle is stopped.