2000 BUICK LESABRE ac reset

yellowblue
2-6
Vehicles are delivered programmed in Mode 3.
Use the following procedure to change modes:
1. Close all the doors and turn the ignition on.
Keep all doors closed throughout this procedure.
2. Press and hold LOCK on the driver's power door
lock switch throughout this procedure. All the doors
will lock.
3. Press the button with the lock symbol on the remote
keyless entry transmitter. The automatic door locks
will remain in the current mode.
4. Press the button with the lock symbol on the
transmitter again. Each time this button is pressed,
the mode will advance by one, going from
3 to 0 to 1, etc.
Note: The door locks will cycle according to the
mode entered while customizing the memory door
locks. (Mode ª0º has no feedback.)
5. Release the power door lock switch. The automatic door
locks will remain in the most recent mode selected.This procedure only changes the mode for the
transmitter used to change this setting. The procedure
will need to be repeated for the second transmitter.
If your vehicle is equipped with the Driver Information
Center (DIC), you must program this feature through the
DIC. See ªDriver Information Centerº in the Index.
Delayed Locking
This feature lets the driver delay the actual locking of
the vehicle. When the driver's power door lock switch
or remote keyless entry lock button is pressed with the
key removed from the ignition, and the driver's door
open, a chime will sound three times to signal that
delayed locking system is active. When all doors have
been closed, the doors will lock automatically after five
seconds. If any door is opened before this, the
five
-second timer will reset itself once all the doors have
been closed again.
Pressing the driver's door lock switch or remote keyless
entry transmitter button again will override this feature.
Pressing the passenger's door lock switch will also
override this feature.

yellowblue
2-40 Windshield Washer
At the top of the turn signal/multifunction lever, there's
a paddle with the word PUSH on it. To spray washer
fluid on the windshield, push the paddle. The wipers
will clear the window and either stop or return to your
preset speed.
CAUTION:
In freezing weather, don't use your washer until
the windshield is warmed. Otherwise the washer
fluid can form ice on the windshield, blocking
your vision.
Cruise Control
The controls to operate the cruise control are located on
the steering wheel.
With cruise control, you can maintain a speed of about
25 mph (40 km/h) or more without keeping your foot on
the accelerator. This is helpful on long trips.
Cruise control does not work at speeds below about
25 mph (40 km/h).
When you apply your brakes, the cruise control
shuts off.

yellowblue
2-42
Resuming a Set Speed
Suppose you set your cruise control at a desired speed
and then you apply the brake. This, of course, shuts off
the cruise control. But you don't need to reset it.
Once you're going about 25 mph (40 km/h) or more,
you can briefly press the RESUME/ACCEL
(resume/accelerate) button to return to your desired
preset speed.
You'll go right back up to your chosen speed and stay
there. If you press and hold the RESUME/ACCEL
button, the vehicle will keep going faster until you
release the button or apply the brake. So unless you
want to go faster, don't press and hold the
RESUME/ACCEL button.
Increasing Speed While Using Cruise Control
There are two ways to go to a higher speed:

Use the accelerator pedal to get to the higher speed.
Press the SET/COAST button, then release the
button and the accelerator pedal. You'll now cruise at
the higher speed.
Press the RESUME/ACCEL button. Hold it there
until you get up to the speed you want, and then
release the button. (To increase your speed in very
small amounts, briefly press the RESUME/ACCEL
button and then release it. Each time you do this,
your vehicle will go about 1 mph (1.6 km/h) faster.)
The accelerate feature will only work after you have set the
cruise control speed by pressing the SET/COAST button.
Reducing Speed While Using Cruise Control
There are two ways to reduce your speed while using
cruise control:

Press the SET/COAST button until you reach the
lower speed you want, then release it.

To slow down in very small amounts, push the
SET/COAST button briefly. Each time you do this,
you'll go 1 mph (1.6 km/h) slower.
Passing Another Vehicle While Using Cruise Control
Use the accelerator pedal to increase your speed. When
you take your foot off the pedal, your vehicle will slow
down to the cruise control speed you set earlier.

yellowblue
2-66 Speedometer and Odometer
Your speedometer lets you see your speed in both miles
per hour (mph) and kilometers per hour (km/h). Your
odometer shows how far your vehicle has been driven,
in either miles or kilometers. Press The ENG/MET
button which is located to the left of the speedometer to
change from mph to km/h.
Your vehicle has a tamper resistant odometer.
You may wonder what happens if your vehicle needs a
new odometer installed. If the new one can be set to the
mileage total of the old odometer, then it must be. But if
it can't, then it's set at zero and a label must be put on
the driver's door to show the old mileage reading when
the new odometer was installed.
Trip Odometer
A trip odometer can tell you how far you have driven
since you last set it to zero. To reset it, push the TRIP
RESET button. If your vehicle is equipped with a DIC,
see ªDICº in the Index for information on resetting the
trip odometer.
Tachometer (If Equipped)
The tachometer tells you
how fast the engine is
running. It displays engine
speed in thousands of
revolutions per
minute (rpm).
NOTICE:
Do not operate the engine with the tachometer in
the red area or engine damage may occur.

yellowblue
2-70
When the ignition is on, the brake system warning light
will also come on when you set your parking brake.
The light will stay on if your parking brake doesn't release
fully. If you try to drive off with the parking brake set, a
chime will also come on until you release the parking
brake. If the light and chime stay on after your parking
brake is fully released, it means you have a brake problem.
Anti-Lock Brake System Warning Light
With the anti-lock brake
system, the light(s) will
come on when you start
your engine and may stay
on for several seconds.
That's normal.
If the light stays on, turn the ignition to OFF. Or, if the
light comes on when you're driving, stop as soon as
possible and turn the ignition off. Then start the engine
again to reset the system. If the light still stays on, or
comes on again while you're driving, your vehicle needs
service. If the regular brake system warning light
isn't on, you still have brakes, but you don't have
anti
-lock brakes. If the regular brake system warning light is also on, you
don't have anti
-lock brakes and there's a problem with
your regular brakes. See ªBrake System Warning Lightº
earlier in this section.
The anti
-lock brake system warning light should come
on briefly when you turn the ignition key to RUN.
If the light doesn't come on then, have it fixed so it
will be ready to warn you if there is a problem.
Traction Control System Warning
Light (Option)
This warning light should
come on briefly as you
start the engine.
If the warning light doesn't come on then, have it fixed so it
will be ready to warn you if there's a problem. If it stays on, or
comes on when you're driving, there may be a problem with
your traction control system and your vehicle may need
service. When this warning light is on, the system will not
limit wheel spin. Adjust your driving accordingly.

yellowblue
2-81
The following buttons are
on the DIC control panel
which is located to the left
of the steering column:

ODO/TRIP: When this button is pressed, the display
will show the total mileage, and Trip 1 or Trip 2
miles. Trip 1 and Trip 2 will display the miles
traveled since the last reset. To reset the trip
odometer, press the ODO/TRIP button until the
preferred trip number (1 or 2) is shown in the
DIC display, then press the RESET button.
The trip odometer will now accumulate miles until
the next reset.
FUEL INFO: Press this button to display
fuel information.
Press the FUEL INFO button until the display shows
FUEL ECONOMY AVERAGE. Average fuel
economy is viewed as a long term approximation of
your overall driving conditions. To learn the average
fuel economy from a new starting point, press the
RESET button while the average fuel economy is
displayed in the DIC.
Press the FUEL INFO button until the display shows
FUEL ECONOMY INST. Instantaneous fuel
economy varies with your driving conditions, such
as acceleration, braking and the grade of the road
being traveled. The RESET button does not function
in this mode.
Press the FUEL INFO button until the display shows
FUEL RANGE. The fuel range will calculate the
remaining distance you can drive without refueling.
This calculation is based on the average fuel
economy for the last 25 miles (40.25 km) driven, and
the fuel remaining in the fuel tank. The RESET
button does not function in this mode.

yellowblue
2-82

GAGE INFO: Use this button to display oil pressure,
oil life, coolant temperature, tire pressure and
battery information.
Press the GAGE INFO button until OIL PRESSURE
appears in the display. If there are no problems
detected with the oil pressure, the display will show
OIL PRESSURE NORMAL. If a low oil pressure
condition is detected, the display will show OIL
PRESSURE LOW. If you see the OIL PRESSURE
LOW message, your vehicle could be low on oil or
the oil is not going through the engine properly.
See your dealer for service.
Press the GAGE INFO button until COOLANT
TEMP appears in the display. If there are no
problems detected with the temperature, COOLANT
TEMP NORMAL will appear in the display. If the
temperature is too high, COOLANT TEMP HOT
will appear in the display. If you see the COOLANT
TEMP HOT message, the engine is overheated. You
should pull off the road, stop your vehicle and turn
off your engine as soon as possible. This manual
explains what to do. See ªEngine Overheatingº in
the Index.Press the GAGE INFO button until the display
shows BATTERY STATE. If the voltage is normal
the display will show BATTERY STATE NORMAL.
If the voltage drops below 10.5 volts, the display will
show BATTERY STATE LOW. If the voltage is
above 16 volts, the display will show BATTERY
STATE HIGH. If the display shows the high or low
message, you need to have your battery and charging
system checked.
Press the GAGE INFO button until OIL LIFE
INDEX appears in the display. The OIL LIFE
INDEX NORMAL display will show an estimate of
the oil's remaining useful life. When the oil life
index is less than 10%, the display will show OIL
LIFE INDEX CHANGE OIL. When you have the
oil changed according to the maintenance schedule
(see ªMaintenance Scheduleº in the Index), you will
have to reset the oil life monitor. To reset the Oil
Life System (Index), see ªOil Life Systemº or
ªEngine Oil, When to Changeº in the Index.

yellowblue
2-83
Press the GAGE INFO button until TIRE PRESSURE
appears in the display. TIRE PRESSURE NORMAL is
displayed when the Check Tire Pressure System
believes your vehicle's tire pressures are normal. If a
potential tire pressure problem is detected, the display
will show TIRE PRESSURE LOW: CHECK TIRES.
If you see the TIRE PRESSURE LOW: CHECK
TIRES message, you should stop as soon as you can
and check all your tires for damage. (If a tire is flat, see
ªIf a Tire Goes Flatº in the Index.) Also check the
tire pressure in all four tires as soon as you can.
See ªInflation
-- Tire Pressureº and ªCheck Tire
Pressure Systemº in the Index. There are times
when you will have to reset (calibrate) the Check
Tire Pressure System. See ªCheck Tire Pressure
Systemº in the Index.

RESET: This button, used along with other buttons,
will reset system functions.

ENG/MET: Use this button to change the display
between English and metric units.
DIC Warnings and Messages
Other messages or warnings may appear in the DIC
display. For Canadian drivers, in addition to the DIC
message your DIC will display EXP with a number after
it which reflects the following messages:EXP (Export ID) Warning Message
2 ENG COOLANT LOW
- CHECK LEVEL . . . . . .
20 TURN SIGNAL STILL ON?. . . . . . . . . . . . . . . .
24 TRUNK AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
25 WINDSHIELD WASHER FLUID LOW. . . . . . .
27 BATTERY SAVER ACTIVE. . . . . . . . . . . . . . . .
36 ENGINE OIL LOW
- CHECK LEVEL . . . . . . . .
40 THEFT ATTEMPT DETECTED. . . . . . . . . . . . .
54 SERVICE STABILITY SYSTEM. . . . . . . . . . . .
55 STABILITY SYSTEM ACTIVE. . . . . . . . . . . . .
61 GAS CAP LOOSE
- CHECK CAP . . . . . . . . . . .
81 CHANGE ENGINE OIL SOON. . . . . . . . . . . . .
91 TRACTION CONTROL SYSTEM ACTIVE. . .
102 CHECK CHARGE SYSTEM. . . . . . . . . . . . . . .
139 DOOR AJAR. . . . . . . . . . . . . . . . . . . . . . . . . . .
144 CHECK TIRE PRESSURE. . . . . . . . . . . . . . . .
The EXP codes are used to make translation from
English to other languages easier.
Pressing any of the DIC control buttons will remove the
messages or warnings from the DIC display.