2000 AUDI A8 sensor

38-25

All:

- Remove valve body from transmission while
advancing the wiring harness connector.

Note only for Park/Neutral Position (PNP)
Switch -E17-:
Do not place the removed valve body on the
Sensor for transmission RPM at rear of valve
body. Danger of damage.

Installing

- Lightly coat O-rings of wiring harness connector
with ATF.

- Insert wiring harness connector into
transmission housing.


Installation position: Flat part of rear collar
points downward, the tabs at collar are
horizontal

Only for transmission with hydraulic control
E18/2

- Route wire with connector -C- according to illustration, so that the wire
is not pinched when installing the valve body.
Pa
ge 25 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-27

Only for transmission with hydraulic control
E18/2

Only for Park/Neutral Position (PNP) Switch -E17- - Pull wiring with connector -B- of Sensor for transmission RPM -G182-
between valve body and wiring harness upward.
- Connect connector -B- to connector -A- at wiring harness.
- Connect connector -C- to Transmission Vehicle Speed Sensor (VSS) -
G38-.

- Connect connector (arrow) to Transmission Vehicle Speed Sensor
(VSS) -G38-.
Pa
ge 27 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-35

Speedometer Vehicle Speed Sensor
(VSS) -G22-, removing and installing


Removing

- Disconnect harness connector from
Speedometer Vehicle Speed Sensor (VSS) -
G22-.

- Push retaining bracket of sensor downward, turn
and pull sensor out.

Installing

- Replace sealing rings (arrows).
- Insert O-rings with grease.
- Insert sensor.
- Engage retaining bracket at mounting bracket for flange shaft.
Pa
ge 35 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-36

Sensor for transmission RPM -G182-,
removing and installing


Note:

There is a distinction made between two types
of transmission. Transmissions with hydraulic
control E17, the sensor for transmission RPM
(inductive sensor) is secured to bottom of valve
body. Transmissions with hydraulic control
E18/2, the sensor for transmission RPM (hall
effect sensor) is secured to transmission
housing behind valve body.
Information regarding which transmission is
installed can be found in tables page 00
-4
onward.

For transmissions with hydraulic control E17

Removing

- Removing valve body page 38
-22
.

- Turn valve body on its back side and loosen connector at Sensor for
transmission RPM -1-.
Pa
ge 36 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-37


Installing - Unbolt Sensor for transmission RPM -1- at valve body.
- Tighten Sensor for transmission RPM -1- using spacer sleeves -2-
(height: 20 mm) to 7 Nm.

Installation position: Sensor-side with the connector terminals
points to valve body center.

- Connect connector to Sensor for transmission RPM -1-.
- Installing valve body page 38
-25
.
- Fill up ATF page 37
-140
.
Pa
ge 37 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-38

For transmissions with hydraulic control
E18/2

Removing

- Removing valve body page 38
-22
.

Installing - Unbolt Sensor for transmission RPM -A- from transmission.
- Bolt on Sensor for transmission RPM -A- at transmission via bolt -B-.
Tightening torque is 9 Nm.
Pa
ge 38 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-40

Transmission Vehicle Speed Sensor
(VSS) -G38-, removing and installing


Removing

- Removing oil pan page 38
-19
.

- Disconnect harness connector from Transmission Vehicle Speed
Sensor (VSS) -G38- (arrow).

Installing - Remove Transmission Vehicle Speed Sensor (VSS) -2-.
- Install and tighten Transmission Vehicle Speed Sensor (VSS) -2- using
spacer sleeve -1- (height: 8 mm) to 6 Nm.
Pa
ge 40 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1

38-41


- Connect connector at Transmission Vehicle Speed Sensor (VSS) -
G38-.
- Installing oil pan page 38
-20
.
- Fill up ATF page 37
-140
.
Pa
ge 41 of 44 Oil
pan, oil strainer and valve bod
y, removin
g and installin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT01.38.1