2000 AUDI A6 engine

01-277
88-pin connector for Transmission Control Module (TCM) -J217- (sockets on VAG1598/20)
1- Solenoid valve 5 -N92- 18-
Kick-down switch -F8- (not for E-gas and V6-TDI)
2- Shift lock solenoid -N110- 19-
Control input to transmission from ABS control module
3- Vacant 20-
Engine intervention (via ignition timing)
1)
4- Solenoid valve 7 -N94- 21-
ATF temperature sensor -G93-
5- Solenoid valve 4 -N91- 22-
ATF temperature sensor -G93-
6- Ground (GND) for power consumers, term.
31 23-
Sensor for transmission RPM -G182- (shielding)
7- Vacant 24-
Vacant
8- Multi-function TR switch -F125-, L2 25-
Selector lever display (not for Highline combi)
9- Multi-function TR switch -F125-, L4
supply voltage for cruise control system 26-
Supply voltage (terminal 30) with or without fuses depending on
model wiring diagram
10-
Brake light switch -F- (not for E-gas and
V6-TDI) 27-
Kick-down for air conditioning
1)
11-
Vacant 28-
Ground (GND) for electronics (terminal 31)
4)
12- Vacant 29- Solenoid valve 6 -N93-
Pa
ge 7 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-278

35- Fuel consumption signal
(engine torque, actual)
1) 54- Supply voltage (terminal 15)
36- Multi-function TR switch -F125-, L1 55- Supply voltage (terminal 15)
37- Multi-function TR switch -F125-, L3 56- Vacant
38- Vacant -
39- Vacant -
40-
Engine speed (RPM) signal
1)
-
41-
Throttle position value (load signal)
1)
-
42- Transmission VSS -G38- -
43- Vacant -
44- Sensor for transmission RPM -G182- - Terminals 57 - 83 are vacant
45- Vacant -
46- Tiptronic upshift switch -
47- Tiptronic downshift switch -
48- Vacant -
49- Vacant 84- Vacant
50- Vacant 85-
CAN-bus
3)
51- Upshift/downshift signal
(for engine torque reduction) 86-
CAN-bus 3)
Pa
ge 9 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-279
1) Only for vehicles without a CAN-bus.

Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00; Code letters, engine/transmission applications, ratios, equipment

2) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM) and can only be checked
in read measured value block page 01
-186
.
3) Only for vehicles with a CAN-bus. Further information for CAN-BUS on the CAN-bus page 01
-263


Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00; Code letters, engine/transmission applications, ratios, equipment

4) Pin 28 at the control module is vacant for vehicles with 10-pin connector of multi-function switch -F125-.
Pa
ge 11 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-280
List of test steps (88-pin connector)

Only perform test steps for the relevant component, as listed in DTC and Read Measuring Value Block tables.
Item checked
Item checked
Supply voltage for TCM -J217-
- Perform test
steps 1 and 7 Solenoid valve 5 -N92- (Pressure control
valve -2- -N216-) - Perform test steps 13
and 8
Shift lock solenoid -N110-
- Perform steps 2,
6 and 16 Solenoid valve 6 -N93- (pressure control
valve -3- -N217-) - Perform test steps 14
and 8.
Brake light switch -F-
- Perform test
step 3. Solenoid valve 7 -N94- (pressure control
valve -4- -N218-) - Perform test steps 15
and 8.
Supply voltage for cruise
control system - Perform test
step 4. Transmission VSS -G38- (Sensor for
transmission output RPM -G195-) - Perform test step 18.
Kick-down switch -F8-
(not for E-gas) - Perform test
steps 5 and 17 Sensor for transmission RPM -G182-
- Perform test step 19.
Multi-function TR switch
(driving range sensor) -F125- - page 01
-322
ATF temperature sensor -G93-
- Perform test step 20.
Solenoid valve 1 -N88-
- Perform test
steps 8 and 9 Wiring connection to ECM
1)
- Perform test steps 21,
22, 23, 24, and 25
1) Signal is transmitted to Transmission Control Module (TCM) via the Engine Control Module (ECM). Test is only for vehicles
without CAN-bus.
Pa
ge 12 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-281

Item checked
Item checked
Solenoid valve 2 -N89-
- Perform test steps
10 and 8 Tiptronic switch -
F189- - Perform test steps 26 and 27
Solenoid valve 3 -N90-
- Perform test steps
11 and 8 CAN-bus
2)
- Perform test step 28 and check CAN-bus
system page 01
-265
.
Solenoid valve 4 -N91-
(Pressure control valve -1-
-N215-) - Perform test steps
12 and 8 2) Only for vehicles with CAN-bus

Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00; Code letters, engine/transmission applications, ratios, equipment


Repair Manual, 5 Spd. Automatic Transmission 01V, Repair Group 00; Code letters, engine/transmission applications, ratios, equipment

Pa
ge 13 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-283

Voltage measurement: switch multimeter to 20 V measuring range
Test step
VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
3
1)
10 + 6
10 +
28
2) Brake light switch
-F-
Ignition switched
on Brake pedal not
depressed less than 1 V
- Check wiring per wiring
diagram.
- Replace and adjust brake
light switch -F-.
not for E-gas
engines
- Brake pedal
depressed approx. battery
voltage Repair Manual, Brake
System, Repair Group 47

4 9 + 6
9 + 28
2) Supply voltage for
Cruise Control, Control
Module
-J213-
Ignition switched
on Selector lever in
D, 4 and 3 approx. battery
voltage - Check wiring from terminals
6 and 28 to Ground.
- Check wiring from terminal 9
to terminal 15 of central
electrics.
- Check wiring to cruise
control, control module -J213-
- Check multi-function switch -
F125- page 01
-322


Selector lever in
P, R, N, and 2 less than 5 V
- Check fuse 31
Pa
ge 16 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

1) This test cannot be performed on vehicles with E-gas. The signal is transmitted from brake light switch or brake test switch
to Engine Control Module (ECM). The ECM then forwards the signal to the Transmission Control Module via the CAN-Bus. 2) Pin 28 at the control module is vacant for vehicles with 10-pin connector of multi-function switch -F125-.
Pa
ge 17 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16

01-284

Voltage measurement: switch multimeter to 20 V measuring range
Test step
VAG
1598/20
sockets Test of
Test conditions
- Additional stepsSpecified
value Corrective action
5
1)
not for E-gas
engines 18 + 54 Kick-down
switch -F8-
Ignition switched on
- Depress accelerator to
kick-down approx. battery
voltage
Repair Manual, General,
Engine, Repair Group 20 - Check wiring per wiring
diagram.
- Adjust or replace accelerator
pedal cable.
- Perform test step 17.
1) This test cannot be performed on vehicles with E-gas. The kick-down switch -F8- in this case is integrated in the Throttle
Position (TP) Sensor (-G79-, -G185-).
Pa
ge 18 of 66 Electrical testin
g
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.AT02.01.16