2000 AUDI A4 display

01-91

Check DTC Memory (scan tool function
02)


Note:
The displayed DTC information is updated only
when initiating OBD or with "Erase DTC Memory"
function 05.

- Switch printer on via the PRINT button (indicator
lamp in button lights up).
Rapid data transfer
HELP
Select function XX

Indicated on display
- Press buttons -0- and -2-. This selects "Check DTC memory", function
02.
Rapid data transfer
Q
02 - Check DTC memory

Indicated on display
- Press -Q- button to confirm input.
X DTC reco
gnized!

The number of stored malfunctions appears in the display.
The stored malfunctions are displayed and printed out one after the
other.
- Check print-out against DTC table and repair malfunction Page 01
-
93
.
Pa
ge 15 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-92

No DTC recognized!

If "No DTC recognized!" is displayed, the program will return to "Select
function XX" after the button is pressed.
Rapid data transfer
HELP
Select function XX

Indicated on display
If something else is displayed:
Operating instructions of Scan Tool (ST) - End Output (function 06) Page 01
-109
- Switch off ignition and disconnect diagnostic connector.
Pa
ge 16 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-93
Diagnostic Trouble Code (DTC) table for instrument cluster

Notes:

The following table lists all malfunctions that can be recognized by the instrument cluster and printed out by the VAG1551
scan tool. The malfunctions are listed in order according to their 5-digit numbers.
DTC numbers appear only on the print-out.
Before replacing a component shown as faulty, check the wiring and connections to the component as well as the Ground
(GND) connections according to wiring diagram.
After repairs and function test of the system, DTC memory must always be checked again using the VAG1551 scan tool
and erased.
DTC memory stores all static and sporadic malfunctions: If a malfunction occurs and persists for at least 2 seconds, it is
identified as a static malfunction (outside temperature malfunction at least 60 seconds, coolant temperature sensor only
after at least 30 minutes with engine running). If a malfunction does not occur again, it is registered as sporadic. "/SP" will
appear at right on scan tool display.
When the ignition is switched on, all existing malfunctions are automatically re-classified as sporadic malfunctions and will
only register as static malfunctions if they still occur after testing.
Sporadic malfunctions which no longer occur during 50 driving cycles (ignition on at least 5 minutes, vehicle speed 30
km/h) are erased automatically.
Pa
ge 17 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-94

VAG 1551 scan tool display
Possible causes
Corrective action
00562
Oil level thermal sensor -
G266-

Open circuit/short circuit to
B+
Short circuit to Ground
Implausible signal
Open circuit or short circuit
between oil level thermal sensor
-G266- and instrument cluster Oil level thermal sensor -G266-
faulty -G266- faulty Electronic part in sensor faulty- Locate malfunction using wiring diagram
- Repair open circuit
- Oil level thermal sensor -G266- faulty Replace -
G266-
00667
Outside temperature signal

Open circuit/short circuit to
B+
Short circuit to Ground
implausible signal (is
indicated incorrectly and
must be disregarded)
Open circuit or short circuit
between instrument cluster and
A/C control head -E87- A/C control head -E87- faulty
Repair Manual, Heating & AirConditioning, Repair
Group 01
- Locate malfunction using wiring diagram
- Repair open circuit
- A/C system OBD
00668
Vehicle voltage, terminal 30

Voltage supply too low
Battery was disconnectedOpen circuit or short circuit to a
control module or sensor - Perform automatic test sequence in order to
determine the control module responsible for the
DTC check voltage supply of malfunctioning
control module
- Locate malfunction using wiring diagram
Pa
ge 18 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-95

VAG 1551 scan tool
display Possible causes
Corrective action
00771
Sender for fuel gauge -G-

Open circuit/short
circuit to B+
Short circuit to Ground
Open circuit or short circuit between sender for fuel
gauge -G- (Front Wheel Drive/All Wheel Drive) and
instrument cluster
Sender for fuel gauge -G- (Front Wheel Drive/All
Wheel Drive) is faulty - Locate malfunction using wiring
diagram
- Repair open circuit
- - Replace Sender for fuel gauge -
G- (Front Wheel Drive/All Wheel
Drive)
00779
Outside air temperature
sensor -G17-

Open circuit/short
circuit to B+
Short circuit to Ground
Open circuit or short circuit
Outside air temperature sensor -G17- faulty - Locate malfunction using wiring
diagram
- Repair open circuit
- Replace outside air temperature
sensor -G17-
01039
Engine Coolant
Temperature (ECT) sensor
-G2-

Open circuit/short
circuit to B+
Short circuit to Ground
Open circuit or short circuit between Engine Coolant
Temperature (ECT) sensor -G2- and instrument
cluster
Engine Coolant Temperature (ECT) sensor -G2-
faulty - Locate malfunction using wiring
diagram
- Repair open circuit
- Replace Engine Coolant
Temperature (ECT) sensor -G2-
Pa
ge 20 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-96

VAG 1551 scan tool
display Possible causes
Corrective action
01300
Control module for
navigation with CD
mechanism -J401-

no communication
Open circuit or short circuit
Incorrect control module, that is, control module does
not support CAN
A control module that supports CAN is not indicated with
a "1" in measuring value block Page 01
-132
If control
module for navigation with CD-mechanism -J401- is not
displayed with "1"
Adaptation for the instrument cluster was not performed
properly - Locate malfunction using
wiring diagram
- Repair open circuit
- Replace control module with
a control module that supports
CAN
- Select adaptation channel 62
and input the correct
adaptation value Page 01
-
190
.
01304
Radio

no communication
Open circuit or short circuit
Incorrect control module, that is, control module does
not support CAN
A control module that supports CAN is not indicated with
a "1" in measuring value block Page 01
-132
.
Adaptation for the instrument cluster was not performed
properly - Locate malfunction using
wiring diagram
- Repair open circuit
- Replace control module with
a control module that supports
CAN
- Select adaptation channel 62
and input the correct
adaptation value Page 01
-
190
.
Pa
ge 21 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-97

VAG 1551 scan
tool display Possible causes
Corrective action
01311
Data-BUS
information

faulty
in single wire
mode
Open circuit or short circuit to a control module in
information data-BUS
Incorrect control module in information data-BUS,
that is, control module does not support CAN.
A control module that supports CAN is not indicated
with a "1" in measuring value block Page 01
-132
.
During adaptation of the instrument cluster, a control
module that supports CAN was not concurrently
adapted
Data bus is operating on only one wire (this can
cause EMV problems) - Locate malfunction using wiring diagram
- Repair open circuit
- Replace control module with a control
module that supports CAN
- Select adaptation channel 62 and input
the correct adaptation value Page 01
-
190
.
- Check data exchange Page 01
-196
.
Pa
ge 22 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2

01-98

VAG 1551 scan tool
display Possible causes
Corrective action
01312
Powertrain data-BUS

faulty
Open circuit or short circuit to a control module in
powertrain data-BUS
A control module in the powertrain data-BUS is incorrect,
that is, control module does not support CAN
A control module that supports CAN is not indicated with a
"1" in measuring value block Page 01
-129
.
During adaptation of the instrument cluster, a control
module that supports CAN was not concurrently adapted - Locate malfunction using wiring
diagram
- Repair open circuit
- Replace incorrect control module
with a control module that supports
CAN
- Select adaptation channel 60 and
input the correct adaptation value
Page 01
-183
.
01314
Engine Control
Module (ECM)

no communication
Open circuit or short circuit
Incorrect control module, that is, control module does not
support CAN
A control module that supports CAN is not indicated with a
"1" in measuring value block Page 01
-129
If Engine
Control Module (ECM) is not displayed with "1"
Adaptation for the instrument cluster was not performed
properly - Locate malfunction using wiring
diagram
- Repair open circuit
- Replace control module with a
control module that supports CAN
- Select adaptation channel 60 and
input the correct adaptation value
Page 01
-183
.
Pa
ge 23 of 99 Instrument cluster with lon
g service life, On Board Dia
gnostic
(OBD
) (from m.
y. 2000
)
11/20/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.EE01.01.2