2000 AUDI A4 automatic transmission

01-150

Basic Setting (scan tool function 04)


Notes:

Basic setting is carried out with engine
running.
The OBD II engine control module shows the
"Readiness Code" in display group 29. The
readiness code is reset when the engine control
module power is off and each time the DTC
memory is erased. In order to regenerate the
readiness code it is necessary to take a trip in
"mixed city and highway" driving-approx. 1-1/2
to 5 minute drive at 80-100 km/h (50-63 mph)
with manual transmission in 4th or 5th gear,
preferably 4th gear, or automatic transmission
selector lever in "D" position.
When the "Basic Setting" function 04 is initiated
with the VAG 1551 scan tool, the learning
values are relearned in systems capable of
learning. Learning is prohibited, as soon as a
malfunction is stored in the DTC memory that
relates to a system capable of learning (not with
sporadic malfunctions).
All learning values are erased by disconnecting
the connector from the Engine Control Module
(ECM). After that, uneven idle can occur briefly.
In this case, let engine run in idle for a few
Pa
ge 205 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-163
Display group 000
Note:
If the values displayed do not correspond to the specified values, the following display groups 001 to 010 can be used to
repair malfunctions. Display
field Specified
display value Corresponds to
physical values Designation and conversion to physical values
1 135 - 160
85 - 110 C
Momentary coolant temperature, display -50 = ___ C
2 145 - 158 1.45 - 1.58 V Mass Air Flow (MAF) sensor output voltage, display: 100 = 1 V
3 26-30 650-750 RPM Momentary engine speed, display X 25 = ____RPM
4 0 - 14
or
255 - 240 Idle speed control learning value, with manual transmission in idle
position and/or with automatic transmission with selector lever setting
P or N (average = 0)
5 0 -10
or
255 - 236 Idle speed control learning value, with automatic transmission in
selector lever setting D 1, 2, 3 or R (average = 0)
(On manual transmission vehicles, 0 is always displayed.)
6 126 - 130 Idle speed control feedback (average 128)
7 20 Shift inputs
8 120-136 Oxygen sensor control (average 128/cylinders 1 to 3) "0" is always
displayed on engines without oxygen sensor probe.
Pa
ge 227 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-166
Test table display group 001 Display
field Display on
VAG 1551 scan
tool Malfunction cause
Malfunction repair
1 Greater than
110
or
Less than 85
Engine Coolant Temperature (ECT)
sensor -G62-
Wiring connection to Engine Control
Module (ECM) -J192-
Coolant thermostat faulty
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 19
- Check DTC memory page 01
-13
- Check -G62- page 28
-25
- Check engine coolant thermostat
2 Less than 1.450
V
Large intake air leak between intake
manifold and Mass Air Flow (MAF)
sensor Repair cause
Greater than
1.580 V Electrical consumers on, steering wheel
at end stop, driving mode selected
(automatic transmission)
Tolerance for new engines: - Switch consumers off
- Center steering wheel
- Put selector lever in P or N position
display group 004, display field 4
Max. 1.660 V
When engine speed increases, the display
value increases to 2.500 V, falls to 0.000 V
Pa
ge 231 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-169

Display
field Display on VAG
1551 scan tool Malfunction cause
Malfunction repair
3 Outside tolerance
range
Closed Throttle Position (CTP)
switch activated or faulty CTP switch or throttle position
sensor -G69- incorrectly adjusted Electrical consumers onSteering wheel at end stopDriving mode selected (automatic
transmission) Moisture in connector for -G69-Ground point on intake manifold - Check DTC memory page 01
-13
- Check and adjust -G69- page 24
-77
- Switch electrical consumers off
- Center steering wheel
- Selector lever in P or N display group 004,
display field 4 - Visual inspection
- Check ground connection according to wiring
diagram
4 0 or 1
Closed Throttle Position (CTP)
switch -F60- faulty Throttle position sensor -G69-
incorrectly adjusted Throttle sticks Floor mat presses against
accelerator pedal Moisture in connector of -G69-Accelerator pedal cable adjustment Display group 011, display field 4
Repair Manual, 2.8 Liter V6 2V Engine
Mechanical, Engine Code(s): AFC, Repair Group 20
- Check DTC memory page 01
-13
- Check and adjust -F60- page 24
-73
- Visual inspection
- Adjust accelerator pedal cable:
Pa
ge 235 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-170
Display group 003 Display shows
Display/specified value
Designation
Basic setting 3
1 2 3 4 650 - 750 RPM 1 = Momentary idle speed
15.0 - 35.0% 2 = Engine load idle1)
0% and/or greater than 95% 3 = Throttle angle - at idle: 0%; at wide open throttle: > 95%
... km/h 4 = Momentary vehicle speed 1) Evaluate engine load tolerance range only at idle during "Basic Setting" function 04.
Note on display field 1:
Idle speed on vehicles without A/C and rear windshield heater switched on: 750-850 RPM.
Notes on display field 3:
For the testing at wide open throttle, stop engine, and switch ignition on.
Since in vehicles with manual transmission and automatic transmission different throttle bodies are installed, the start of
opening of the throttle body can be measured with ignition on and thus incorrect installation can be checked
Manual transmission: 45-53%
Automatic transmission: 27-35%
Pa
ge 237 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-171
Test table display group 003 Display
field Display on VAG
1551 scan tool Malfunction cause
Malfunction repair
1 Greater than 750
RPM
Closed Throttle Position (CTP)
switch -F60- Large air leak quantity Idle Air Control (IAC) valve -N71-
sticks or is hard to move Rear windshield heater on Display group 04, display field 4
- Check -F60- page 24
-73
- Repair cause
- Check using output diagnostic test mode
page 01
-145

- Switch electrical consumers off
Less than 650 RPM
Idle Air Control (IAC) valve -N71-
sticks or is hard to move Closed Throttle Position (CTP)
switch -F60- Driving mode selected (automatic
transmission) Display group 004, display field 4
- Check using output diagnostic test mode
page 01
-145

- Check -F60- page 24
-73
- Move selector lever to P or N
2 Outside tolerance
range
Poor idle (not running on all
cylinders) Mass Air Flow (MAF) sensor -G70-
faulty Idle Air Control (IAC) valve -N71-
faulty Electrical consumers on- Fuel injectors or spark plugs faulty
- Check DTC memory page 01
-13
and/or
display group 001, display field 2 and 3
- Check DTC memory page 01
-13
and/or
display group 018
- Switch electrical consumers off
- Center steering wheel
Pa
ge 238 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

Steering wheel at end stopDriving mode selected (automatic
transmission) - Move selector lever to P or N
Pa
ge 239 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1

01-173
Display group 004 Display
shows Display/specified
value Designation
Basic
setting 4
1 2 3 4 0 2
1 = Idle air control valve at idle
HS: +14 to -16
or
AT: +10 to -20 2 = Idle speed control learning value in manual transmission (HS) at idle setting and/or
with automatic transmission (AT) in selector lever setting P or N
Variation permitted for new engines:
HS: +20 to -16AT: +16 to -20)
HS: 0
or
AT: +10 to -20 3 = Idle speed control learning value in automatic transmission (AT) in selector lever
setting D, 1, 2, 3 or R. (0 is always displayed in vehicles with manual transmission.)
001 10 4 = Shift inputs at idle:
0 off 1 on
Notes:

Values in display fields 2 and/or 3 can only be evaluated with idle air control valve is within tolerance at idle (display value
1). If the idle air control valve is not within tolerance after 1 minute waiting time, no learning takes place in display fields 2
and/or 3 .
Pa
ge 242 of 366 On Board Dia
gnostic
(OBD
) - Multi
port Fuel In
jection
(MFI
)
11/22/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.FU01.01.1