2000 AUDI A4 AEB ATW Engines Cylinder Head Remove And Install Workshop Manual

15-10

Intake manifold, removing and installing


Removing

Note:
All tie wraps opened or cut during removal must
be reinstalled at the same locations.

CAUTION!

BEFORE disconnecting the battery:

Stop the engine.
Be sure the ignition is switched OFF (also
applies when connecting the battery). Failure
to do so may damage the Engine Control
Module (ECM).
Determine the correct coding for the anti-
theft radio.

- Disconnect battery Ground (GND) strap.
- Remove engine covers.
- Drain coolant Page 19
-4 .
Pa
ge 9 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

15-11


- Remove hose (arrow) for Leak Detection Pump (LDP) -V144-.
Pa
ge 10 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

15-12


Note:
For vehicles with automatic transmission, remove vacuum hose -2- from
behind vacuum booster. - Disconnect Accelerator Pedal (AP) cable from throttle valve control
module -J338- and mounting flange (arrows) without removing
positioning clip.
- Remove air guide hose -6- at throttle valve control module.
- Remove vacuum hose -1-.
- Disconnect vacuum line -3- to Evaporative Emissions (EVAP) canister.
- Disconnect vacuum hose -2- at brake servo.
- Disconnect the following harness connectors:
4 - For Intake Air Temperature (IAT) sensor -G42-
5 - For throttle valve control module -J338-

- Disconnect harness connector from Camshaft Position (CMP) sensor -
G40- (arrow).
Pa
ge 11 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

15-13


- Unbolt fuel supply rail retaining bolts and disconnect vacuum line at
fuel pressure regulator (arrows).
- Disconnect fuel supply rail with injectors from intake manifold and lay
aside in rear of engine compartment on clean cloth.
- Disconnect coolant hoses at upper coolant line.

- Disconnect upper coolant line at intake line and rear coolant flange at
rear of cylinder head (arrows).
Pa
ge 12 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

15-14


Note:
Stuff clean cloths into cylinder head intake ports. - Disconnect crankcase ventilation hose -1- at intake manifold.
- Remove intake manifold brace (arrows).
- Remove dipstick.
- Unbolt intake manifold at flange and remove.
Pa
ge 13 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

15-15

Installing
Installation is the reverse of removal, noting the
following:

Note:
Replace gaskets and O-rings.

- Adjust Accelerator Pedal (AP) cable.

Repair Manual, Fuel Supply System, Repair
Group 20


- Top up coolant Page 19
-6 .

CAUTION!

Be sure the ignition is switched OFF. Failure
to do so may damage the Engine Control
Module (ECM).

- Switch ignition off and reconnect battery Ground
(GND) strap.

- After connecting battery, enter anti-theft code for
radio

Pa
ge 14 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

Radio operating manual
- Fully close power windows to stop.

- Operate all power window switches again for at
least one second in "close" direction to activate
"one touch" opening/closing function.

- Set clock to correct time.
Pa
ge 15 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2

15-16

- Perform throttle valve control module adaptation
to Engine Control Module (ECM).

Repair Manual, 1.8 Liter 5V Turbo Fuel
Injection & Ignition, Repair Group 24
Tightening torques

Component

Tightening
torques
Intake manifold to cylinder
head 10 Nm (7 ft lb)
Intake manifold brace to intake
manifold 20 Nm (15 ft lb)
Intake manifold to bracket 20 Nm (15 ft lb)
Fuel supply rail to intake
manifold 10 Nm (7 ft lb)
Coolant line to coolant flange 10 Nm (7 ft lb)
Coolant line to intake manifold 10 Nm (7 ft lb)
Pa
ge 16 of 35 C
ylinder head, removin
g and installin
g
11/18/2002 htt
p://127.0.0.1:8080/audi/servlet/Dis
play?action=Goto&t
yp
e=re
pair&id=AUDI.B5.GE02.15.2