2000 Acura RL radiator

Servic
e Statio n Procedure s

3. Insert it all the way back in its tube.

4. Remove the dipstick again and
check the level. It should be
between the upper and lower marks.

If it is near or below the lower mark,
see Addin g Oi l on page 215 . Engine Coolant Check
Look at the coolant level in the
radiator reserve tank. Make sure it is
between the MAX and MIN lines. If
it is below the MIN line, see Addin g
Engin e Coolan t on page 219 for
information on adding the proper

coolant.

Refer to Owne r Maintenanc e
Check s on page 213 for information
on checking other items in your
Acura.
Befor e Drivin g
RESERV
E TAN K

UPPE R MAR K
LOWE R MAR K
MA
X
MI N

Owne
r Maintenanc e Check s
You should check the following items at the specified intervals. If
you are unsure of how to perform any check, turn to the page given. Engine oil level — Check every
time you fill the fuel tank. See
page 169.
Engine coolant level — Check the
radiator reserve tank every time
you fill the fuel tank. See page 170.

Windshield washer fluid — Check the level in the reservoir monthly.If weather conditions cause you to
use the washers frequently, check
the reservoir each time you stop
for fuel. See page 225 . Automatic transmission — Check
the fluid level monthly. See page
226.
Brakes — Check the fluid level
monthly. See page 22 8 . Tires —
Check the tire pressure
monthly. Examine the tread for
wear and foreign objects. See page
241.
Lights — Check the operation of
the headlights, parking lights,
taillights, high-mount brake light,
turn signals, brake lights, and license plate lights monthly. See

page 248.

Maintenance

Coolin
g Syste m
Addin g Engin e Coolan t
If the coolant level in the reserve
tank is at or below the MIN line, add coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and
50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda
Antifreeze/Coolant. If it is not
available, you may use another
major-brand non-silicate coolant as a
temporary replacement. Make sure it is a high-quality coolant
recommended for aluminum engines.However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling system to malfunction or fail. Have
the cooling system flushed and
refilled with Honda antifreeze/
coolant as soon as possible. If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
1. Make sure the engine and radiator
are cool.

CONTINUED

Maintenanc e

RESERV
E TAN K
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Coolin
g Syste m

2. Turn the radiator cap counter-
clockwise, without pressing down
on it, until it stops. This relieves
any pressure remaining in the
cooling system.

3. Remove the radiator cap by

pushing down and turning
counterclockwise.

4. The coolant level should be up to

the base of the filler neck. Add
coolant if it is low.

5. Put the radiator cap back on.

Tighten it fully.

6. Pour coolant into the reserve tank.

Fill it to halfway between the MAX
and MIN marks. Put the cap back
on the reserve tank.

Do not add any rust inhibitors or
other additives to your car's cooling
system. They may not be compatible
with the coolant or engine compo-
nents.

Maintenanc e
RADIATO
R CA P
RESERVE TAN K

Coolin
g Syste m

Replacin g Engin e Coolan t
The cooling system should be completely drained and refilled with
new coolant according to the time and distance recommendations in
the maintenance schedule. Only use Genuine Honda Antifreeze/Coolant.
Draining the coolant requires access
to the underside of the car. Unless
you have the tools and knowledge,
you should have this maintenance done by a skilled mechanic.

1. Turn the ignition ON (II). Turn
the heater temperature controldial to maximum heat (climate

control to 90°F/32°C). Turn off

the ignition. Open the hood. Make
sure the engine and radiator are

cool to the touch.

2. Remove the radiator cap.
DRAI
N PLU G
3. Loosen the drain plug on the bottom of the radiator. Thecoolant will come out through the
hole in the splash cover.

CONTINUED

Maintenanc e

Coolin
g Syste m

4. On the right side of the engine block, remove the clip with a plier,
and then remove the drain cap. 5. Remove the reserve tank from its
holder by pulling it straight up.
Drain the coolant, then put the
tank back in its holder. 6. When the coolant stops draining,
tighten the drain plug at the
bottom of the radiator.
Put the drain cap back in place
tightly, then reinstall the clip on
the drain cap securely.
7. Mix the recommended antifreeze with an equal amount of purifiedor distilled water in a clean
container. The cooling system
capacity is:
1.61 US gal (6.1 l ,1.34 Imp gal)

Maintenanc e

CLI
P
DRAI N CA P RESERV
E TAN K
HOLDER
RESERV E TAN K CA P

Coolin
g Syste m

8. Remove the two bolts and the three nuts with a 7/16 in (10 mm)
wrench, then remove the enginecover. 9. Loosen the bleeder bolt on top of
the engine.
Pour coolant into the radiator up to the base of the filler neck.
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles. 10.Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
11.Check the level in the radiator, add coolant if needed.

CONTINUED

Maintenanc e

NUT
S

BOLT S
BLEEDE
R BOL T
Fill u p t o her e

FILLE
R NEC K

Cooling
Syste m

12.Install the engine cover. First tighten the two bolts on the frontof the engine cover, then tighten
the three nuts on the engine cover.

Tightening torque:
7 lbf .
ft (10 N .
m,1.0 kgf.m)

13.Install the radiator cap, and

tighten it to the first stop.
14.Start the engine and let it run until the radiator cooling fan comes onat least twice. Then stop the

engine.
15.Remove the radiator cap. Pour
coolant into the radiator up to the
base of the filler neck and into the
reserve tank up to the MAX mark.
16.Start the engine and hold it at 1,500 rpm until the cooling fancomes on. Turn off the engine.Check the coolant level in the
radiator and add coolant if needed.
17.Install the radiator cap, and tighten it fully.
18. If necessary, fill the reserve tank

to the MAX mark. Install the
reserve tank cap.

Maintenanc e
RESERV
E TAN K