2000 Acura RL check engine

Engin
e Oil

Addin g Oi l
To add oil, unscrew and remove the engine oil fill cap on top of the left
valve cover. Pour in the oil, and replace the engine oil fill cap.
Tighten it securely. Wait a few minutes and recheck the oil level. Do
not fill above the upper mark; you
could damage the engine. Recommende
d Oi l
Oil is a major contributor to your
engine's performance and longevity.
Always use a premium-grade deter- gent oil. It is highly recommended
that you use Genuine Honda Motor Oil in your vehicle for as long as you
own it.
You can determine an oil's SAE
viscosity and Service Classification
from the API Service label on the oil container.
A fuel-efficient oil is recommended for your Acura. This is shown on the
API Service label by the words "Energy Conserving." This oil is
formulated to help your engine use
less fuel. The API Service label also tells you
the service classification of the oil.
Always use an oil that is labeled "API Service SJ." This service rating may
include other classifications, such as
CD. These additional classifications

are not a problem, as long as the
label also carries the SJ classification.
API SERVIC E LABE L
CONTINUED
Maintenanc e
ENGIN
E OI L FIL L CA P

Engin
e Oi l

4. Install a new oil filter according to

instructions that come with it.

5. Put a new washer on the drain bolt,

then reinstall the drain bolt.
Tighten it to:
3 3 lbf.ft (44 N.m , 4.5 kgf.m)

6. Refill the engine with the recom-

mended oil.
Engine oil change capacity
(including filter):
4.9 US qt (4.6 , 4.0 Imp qt)

7. Reinstall the engine oil fill cap.
Start the engine. The oil pressure
indicator light should go out within
five seconds. If it does not, turn off
the engine and reinspect your
work.
8. Let the engine run for several
minutes and check the drain bolt
and oil filter for leaks.
9. Turn off the engine, let it sit for
several minutes, then check the oil
level. If necessary, add oil to bring
the level to the upper mark on the

dipstick.

Improper disposal of engine oil can be
harmful to the environment. If you
change your own oil, please dispose of
the used oil properly. Put it in a sealed
container and take it to a recycling

center. Do not discard it in a trash bin

or dump it on the ground.

Maintenanc e
NOTIC
E

Coolin
g Syste m
Addin g Engin e Coolan t
If the coolant level in the reserve
tank is at or below the MIN line, add coolant to bring it up to the MAX line.
Inspect the cooling system for leaks.
This coolant should always be a mixture of 50 percent antifreeze and
50 percent water. Never add straight
antifreeze or plain water. Always use Genuine Honda
Antifreeze/Coolant. If it is not
available, you may use another
major-brand non-silicate coolant as a
temporary replacement. Make sure it is a high-quality coolant
recommended for aluminum engines.However, continued use of any non-
Honda coolant can result in
corrosion, causing the cooling system to malfunction or fail. Have
the cooling system flushed and
refilled with Honda antifreeze/
coolant as soon as possible. If the reserve tank is completely
empty, you should also check the
coolant level in the radiator.
1. Make sure the engine and radiator
are cool.

CONTINUED

Maintenanc e

RESERV
E TAN K
Removing the radiator cap
while the engine is hot can cause the coolant to spray out,
seriously scalding you.
Always let the engine and radiator cool down before
removing the radiator cap.

Coolin
g Syste m

8. Remove the two bolts and the three nuts with a 7/16 in (10 mm)
wrench, then remove the enginecover. 9. Loosen the bleeder bolt on top of
the engine.
Pour coolant into the radiator up to the base of the filler neck.
Tighten the bleeder bolt when
coolant comes out in a steady
stream with no bubbles. 10.Fill the reserve tank to the MAX
mark. Install the reserve tank cap.
11.Check the level in the radiator, add coolant if needed.

CONTINUED

Maintenanc e

NUT
S

BOLT S
BLEEDE
R BOL T
Fill u p t o her e

FILLE
R NEC K

Cooling
Syste m

12.Install the engine cover. First tighten the two bolts on the frontof the engine cover, then tighten
the three nuts on the engine cover.

Tightening torque:
7 lbf .
ft (10 N .
m,1.0 kgf.m)

13.Install the radiator cap, and

tighten it to the first stop.
14.Start the engine and let it run until the radiator cooling fan comes onat least twice. Then stop the

engine.
15.Remove the radiator cap. Pour
coolant into the radiator up to the
base of the filler neck and into the
reserve tank up to the MAX mark.
16.Start the engine and hold it at 1,500 rpm until the cooling fancomes on. Turn off the engine.Check the coolant level in the
radiator and add coolant if needed.
17.Install the radiator cap, and tighten it fully.
18. If necessary, fill the reserve tank

to the MAX mark. Install the
reserve tank cap.

Maintenanc e
RESERV
E TAN K

Windshiel
d Washer s

Check the level in the windshield
washer reservoir at least monthly during normal usage. In bad weather,
when you use the washers often, check the level every time you stop

for fuel.

The windshield washer reservoir is located behind the driver's side

headlight.

Check the reservoir's fluid level by
removing the cap and looking at the
float. It should be up to the top of the
neck. If the float is at the bottom of
the neck, the reservoir is nearly empty. Fill the reservoir with a good-quality
windshield washer fluid. This increases the cleaning capability and
prevents freezing in cold weather.

Do not use engine antifreeze or a
vinegar/water solution in the

windshield washer reservoir.

Antifreeze can damage your car's paint,
while a vinegar/water solution can

damage the windshield washer pump.

Use only commercially-available

windshield washer fluid.

When you refill the reservoir, clean the edges of the windshield wiper
blades with windshield washer fluid on a clean cloth. This will help to
condition the blade edges.

Maintenance

FLOA
T NOTIC
E

When you refill the reservoir, clean
the edges of the windshield wiper

blades with windshield washer fluid
on a clean cloth. This will help to

condition the blade edges.

Automati
c Transmissio n Flui d
Check the fluid level with the engine
at normal operating temperature.
1. Park the car on level ground. Shut off the engine.
2. Remove the dipstick (yellow loop) from the transmission and wipe it
with a clean cloth.
3. Insert the dipstick into the transmission. Make sure the notch
in the rubber cap fits in the dipstick guide and that you push
the dipstick in all the way.
4. Remove the dipstick and check
the fluid level. It should be
between the upper and lowermarks.
5. If the level is below the lower
mark, add fluid into the tube to
bring it to the upper mark. Always use Honda Premium Formula
Automatic Transmission Fluid (ATF). If it is not available, you
may use a DEXRON® III
automatic transmission fluid as a
temporary replacement. However,
continued use can affect shift quality. Have the transmission
drained and refilled with Honda
ATF as soon as it is convenient.
6. Insert the dipstick back in the transmission. Make sure the notch
fits in the dipstick guide and the dipstick is down all the way.
The transmission should be drained and refilled with new fluid according
to the time and distance recommen- dations in the maintenance schedule.

Maintenanc e UPPE
R MAR K
LOWE R MAR K

DIPSTIC
K

DIPSTIC K GUID E

Brak
e Fluid , Powe r Steerin g

Always use Genuine Honda DOT 3 brake fluid. If it is not available, you should use only DOT 3 or DOT 4
fluid, from a sealed container, as a temporary replacement. However,
the use of any non-Honda brake fluidcan cause corrosion and decrease
the life of the system. Have the
brake system flushed and refilled
with Honda DOT 3 brake fluid as soon as possible.
Brake fluid marked DOT 5 is not
compatible with your car's braking system and can cause extensive

damage.
Brak
e Syste m
The fluid level should be between the MIN and MAX marks on the sideof the reservoir. If the level is at or
below the MIN mark, your brake system needs attention. Have the
brake system inspected for leaks or
worn brake pads. Powe
r Steerin g
You should check the fluid level in the power steering reservoirmonthly. Check the level when the
engine is cold. Look at the side of
the reservoir. The fluid should be
between the UPPER LEVEL and LOWER LEVEL. If it is below the
LOWER LEVEL, add power steering
fluid to the UPPER LEVEL.
Maintenanc e
MA
X MI
N LOWE
R
LEVE L
UPPE
R
LEVE L