1999 YAMAHA YZF-R7 check engine light

1 - 4
INSTRUMENT AND CONTROL FUNCTIONS
INSTRUMENT AND CONTROL FUNCTIONS
EAU00029
Main switch/Steering lock
The main switch controls the ignition
and lighting systems. Its operation is
described below.
EAU00036
ON
Electrical circuits are switched on. The
engine can be started. The key cannot
be removed in this position.
EAU00038
OFF
All electrical circuits are switched off.
The key can be removed in this posi-
tion.
EAU00040
LOCK
The steering is locked in this position
and all electrical circuits are switched
off. The key can be removed in this po-
sition. To lock the steering, turn the
handlebars all the way to the left. While
pushing the key into the main switch,
turn it from “OFF” to “LOCK” and re-
move it. To release the lock, turn the
key to “OFF” while pushing.
1. Push
2. Turn
EW000016
WARNING

Never turn the key to “OFF” or
“LOCK” when the motorcycle is
moving. The electrical circuits will
be switched off which may result in
loss of control or an accident. Be
sure the motorcycle is stopped be-
fore turning the key to “OFF” or
“LOCK”.
EAU01574
(Parking)
The steering is locked in this posi-
tion, and the taillights and auxiliary
lights come on, but all other circuits
are off. The key can be removed in
this position.
To use the parking position, first
lock the steering, then turn the key
to “ ”. Do not use this position for
an extended length of time as the
battery may discharge.
1.
Neutral indicator light “ ”
2. High beam indicator light “ ”
3. Turn indicator light “ ”
4. Fuel indicator light “ ”
EAU00056
Indicator lights
EAU00061
Neutral indicator light “ ”
This indicator comes on when the
transmission is in neutral.
EAU00063
High beam indicator light “ ”
This indicator comes on when the
headlight high beam is used.
EAU00057
Turn indicator light “ ”
This indicator flashes when the turn
switch is moved to the left or right.
EAU01154
Fuel indicator light “ ”
When the fuel level drops below
approximately 4.8 L, this light will
come on. When this light comes
on, fill the tank at the first opportuni-
ty. This light circuit can be checked
by the procedure on page 1-7.
If there is a shortcircuit or disconti-
nuity at the thermistor, the fuel indi-
cator light will flash 8 times and
then stay off for 3 seconds repeat-
edly.

1 - 5
INSTRUMENT AND CONTROL FUNCTIONS
4 681012
14
x1000r/min
0
1 12
3 3
4

1. Warning light
2. Oil level symbol “ ”
3. Coolant temperature symbol “ ”
4. Engine trouble symbol “ ”
EAU01564
Warning light
This indicator light has three functions.
l
The light will come on and symbol
“ ” will flash if the engine oil
level is low.
If this symbol flashes, stop the en-
gine immediately and fill it with oil
to the specified level.
l
The light will come on and symbol
“ ” will flash if trouble occurs in
a monitoring circuit. In such a
case, take the motorcycle to a
Yamaha dealer to have the self-
diagnostic systems checked.
l
The light will come on and symbol
“ ” will flash if the coolant tem-
perature is too high. The following
chart shows the conditions of the
indicator light, symbol and tem-
perature display in accordance to
coolant temperature.
The light circuit can be checked by the
procedure on page 1-6.
EC000118
CAUTION:

l
Do not run the motorcycle until
you know it has sufficient en-
gine oil.
l
Do not run the motorcycle if the
engine is overheated.
NOTE:

Even if the oil is filled to the specified
level, the indicator light may flicker
when riding on a slope or during sud-
den acceleration or deceleration, but
this is normal.
CB-74ECB-74E
Coolant
temperatureDisplay Conditions What to do
~ 39 ˚CSymbol is on and “LO” is
displayed.OK. Go ahead with riding.
40 ˚C ~ 120 ˚CSymbol is on and temper-
ature is displayed.OK. Go ahead with riding.
121 ˚C ~ 139 ˚CSymbol and temperature
flash.
Warning light comes on.Stop the motorcycle and al-
low it to idle until coolant tem-
perature goes down.
If the temperature does not
go down, stop the engine.
140 ˚C ~ Symbol and message
“HI” flash.
Warning light comes on.Stop the engine and allow it
to cool. Seen page 1-19 if the
engine overheats.
—Symbol and message
“Err” flash.
Warning light comes on.Ask a Yamaha dealer to in-
spect the motorcycle.
C
C
C
C
C

1 - 6
INSTRUMENT AND CONTROL FUNCTIONS
Warning light circuit check
CB-75ECB-75E
Warning light comes on. After a few seconds:Warning light does not come on.
Have a Yamaha
dealer inspect the
electrical circuit.
Turn the main switch to “ON”.
Have a Yamaha dealer inspect
the electrical circuit.
If symbol “ ” is on, check the
engine temperature. (See page 1-5.)
Warning light goes off.
No symbol is on.Symbol “ ”,
“ ” “ ” is on.
OK. Go ahead
with riding.
Warning light does not go off.
If symbol “ ”
is on, inspect the
oil level.
Oil level is OK.Oil level is low.
Have a Yamaha dealer
inspect the electrical
circuit.Supply
recommended
engine oil.
If the engine is hot,
allow it to cool and see
“Engine overheating”
in the troubleshooting
chart on page 1-19 for
instructions.If the engine
temperature is
normal, have a
Yamaha dealer
inspect the
electrical circuit.
If symbol “ ” is on.
Have a Yamaha dealer
inspect the self-
diagnostic systems.

1 - 13
OPERATION AND IMPORTANT RIDING POINTS
1. Turn the main switch to “ON” and
the engine stop switch to “ ”.
ECA00005
CAUTION:
The warning light and fuel indicator
light should come on for a few sec-
onds and then go off. If an indicator
light does not go off, refer to the cor-
responding indicator light circuit
check in the “INSTRUMENT AND
CONTROL FUNCTIONS” section.
2. Shift the transmission into neutral.
NOTE:
When the transmission is in neutral, the
neutral indicator light should be on. If
the light does not come on, ask a
Yamaha dealer to inspect it.
3. Turn on the starter (choke) and
completely close the throttle grip.
4. Start the engine by pushing the
start switch.
NOTE:
If the engine fails to start, release the
start switch, wait a few seconds, then
try again. Each attempt should be as
short as possible to preserve the bat-
tery. Do not crank the engine more
than 10 seconds on any one attempt.5. After starting the engine, move
the starter (choke) to the halfway
position.
NOTE:
For maximum engine life, never accel-
erate hard with a cold engine!
6. After the engine is warm, turn off
the starter (choke) completely.
NOTE:
The engine is warm when it responds
normally to the throttle with the starter
(choke) turned off.
EAU01258
Starting a warm engine
The starter (choke) is not required
when the engine is warm.
EC000046
CAUTION:
See the “Engine break-in” section
prior to operating the motorcycle for
the first time.
1 16
65
5
4 4
3 3
N N2 2
1 1
1. Shift pedal
N. Neutral
EAU00423
Shifting
The transmission lets you control the
amount of power you have available at
a given speed for starting, accelerating,
climbing hills, etc. The use of the shift
pedal is shown in the illustration.
To shift into neutral, depress the shift
pedal repeatedly until it reaches the
end of its travel, then raise the pedal
slightly.
EC000048
CAUTION:
lDo not coast for long periods
with the engine off, and do not
tow the motorcycle a long dis-
tance. Even with gears in neu-
tral, the transmission is only
properly lubricated when the
engine is running. Inadequate
lubrication may damage the
transmission.
lAlways use the clutch when
changing gears. The engine,
transmission, and driveline are
not designed to withstand the
shock of forced shifting and
can be damaged by shifting
without using the clutch.

3 - 20
CHK
ADJCHECKING THE SPARK PLUGS/
MEASURING THE COMPRESSION PRESSURE
5. Check:
• electrodes 1
Damage/wear ® Replace the spark
plug.
• insulator 2
Abnormal color ® Replace the spark
plug.
Normal color is medium-to-light tan.
6. Clean:
• spark plug
(with a spark plug cleaner or wire
brush)
7. Measure:
• spark plug gap a
(with a wire gauge)
Out of specification ® Regap.
8. Install:
• spark plug
NOTE:
Before installing the spark plug, clean
the spark plug and gasket surface.
Spark plug gap
0.7 ~ 0.8 mm (0.028 ~ 0.031 in)
T R..13 Nm (1.3 m · kg, 9.4 ft · lb)
EB303060
MEASURING THE COMPRESSION
PRESSURE
The following procedure applies to all of
the cylinders.
NOTE:
Insufficient compression pressure will
result in a loss of performance.
1. Measure:
• valve clearance
Out of specification ® Adjust.
Refer to “ADJUSTING THE VALVE
CLEARANCE”.
2. Start the engine, warm it up for several
minutes, and then stop it.

3 - 25
CHK
ADJ
CHANGING THE ENGINE OIL
9. Fill:
• crankcase
(with the specified amount of the rec-
ommended engine oil)
10.Install:
• engine oil filler cap
11.Start the engine, warm it up for several
minutes, and then turn it off.
12.Check:
• engine
(for engine oil leaks)
13.Check:
• engine oil level
Refer to “CHECKING THE ENGINE OIL
LEVEL”.
Quantity
Total amount
3.6 L (3.2 lmp qt, 3.8 US qt)
Without oil filter cartridge
replacement
2.6 L (2.3 lmp qt, 2.7 US qt)
With oil filter cartridge
replacement
2.8 L (2.5 lmp qt, 3.0 US qt)
14.Check:
• engine oil pressure
t t t t t t t t t t t t t t t t t t t t t t t t t t t
a. Slightly loosen the oil gallery bolt 1.
b. Start the engine and keep it idling
until engine oil starts to seep from the
oil gallery bolt. If no engine oil comes
out after one minute, turn the engine
off so that it will not seize.
c. Check the engine oil passages, the oil
filter cartridge and the oil pump for
damage or leakage. Refer to “OIL
PAN AND OIL PUMP” in chapter 4.
d. Start the engine after solving the
problem(-s) and check the engine oil
pressure again.
e. Tighten the oil gallery bolt to
specification.
s s s s s s s s s s s s s s s s s s s s s s s s s s s
T R..
Oil gallery bolt
20 Nm (2.0 m • kg, 14 ft • lb)
1
1

8 - 3
–+ELEC

CHECKING THE SWITCHES
EB801010
CHECKING THE SWITCHES
Check each switch for damage or wear, proper connections, and also for continuity between
the terminals. Refer to “CHECKING SWITCH CONTINUITY”.
Damage/wear
® Repair or replace the switch.
Improperly connected ® Properly connect.
Incorrect continuity reading ® Replace the switch.
1Main switch
2Light switch
3Pass switch
4Dimmer switch
5Turn signal switch6Horn switch
7Clutch switch
8Engine stop switch
9Start switch
0Front brake light switchAOil level switch
BRear brake light switch
CFuse
DNeutral switch
ESidestand switch
1L/YL/B
LL/R
R
Br/L
OFF
ONP
L/RLBr/LRL/YL/B
3
4
5
Br/WR/YPLB
Dg Y
G Ch
B/YL/YPASS—
R/YY
67
YG
—BP
(BLUE)
(BLACK)
(BLACK)
R/WBr
R/BB
G/YL/W
B
B
G/YBr
OFF
ChBr/WDg
8R/WR/B
9
0—L/WB
2R/YL•
C
E
(BLUE)
B
B
B D
(BROWN)
Sb
A
W
L/YB/Y
L/YB/Y