1999 YAMAHA YZF-R7 coolant

5 - 15
COOLWATER PUMP
EB503040
ASSEMBLING THE WATER PUMP
1. Install:
• oil seal 1
(into the water pump housing 2)
NOTE:
• Before installing the oil seal, apply tap
water or coolant onto its outer surface.
• Install the oil seal with a socket that
matches its outside diameter.
New
2. Install:
• water pump seal 1
ACHTUNG:CAUTION:
Never lubricate the water pump seal
surface with oil or grease.
NOTE:
• Install the water pump seal with the
special tools.
• Before installing the water pump seal,
apply Yamaha bond No.1215 2 to the
water pump housing 3.
Push down.
Mechanical seal installer 4
90890-04078
Middle driven shaft bearing
driver 5
90890-04058
Yamaha bond No. 1215
90890-85505
New
3. Install:
• rubber damper 1
• rubber damper holder 2
NOTE:
Before installing the rubber damper,
apply tap water or coolant onto its outer
surface.
New
New

8 - 1
–+ELEC

ELECTRICAL COMPONENTS
EB800000
ELECTRICAL
ELECTRICAL COMPONENTS
1
Wire harness
2
Main switch
3
Front brake light switch
4
Ignition coils
5
Clutch switch
6
Throttle position sensor
7
Intake air temperature sensor
8
Intake air pressure sensor
9
Atmospheric pressure sensor
0
Turn signal relay
A
Relay unit
B
ECU
C
CDI unit
D
Fuse box
E
Fall detection switch
F
Starter relay
G
Main fuse
H
Main relay
I
Battery
J
Rectifier/regulator
K
Rear brake light switch
L
Neutral switch
M
Speed sensor
N
Sidestand switch
O
Stator coil assembly
P
Oil level switch
Q
Pickup coil
R
Radiator fan
S
Horn
T
Coolant temperature
sender
U
Thermo switch
V
Camshaft sensor
8

8 - 25
–+ELECCOOLING SYSTEM
TROUBLESHOOTING
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
C0NTINUITYOK
NOTE:
• Before troubleshooting, remove the following part(-s):
1) bottom cowling
2) front cowling
3) rear cowling
• Troubleshoot with the following special tool(-s).
• The radiator fan motor fails to turn.
• The coolant temperature meter needle fails to move when the engine is warm.
Check the main and radiator fan
motor fuses for continuity.Replace.
Check the condition of the bat-
tery.Recharge or replace.
Check the main switch. Replace.
Check the radiator fan motor. Replace.
Check the thermo switch. Replace.
Check the entire cooling system’s
wiring.Repair or replace.
Pocket tester
90890-03112
No good
No good
No good
No good
No good
No good

8 - 26
–+ELECCOOLING SYSTEM
CHECKING THE THERMO SWITCH
• Remove the thermo switch from the radia-
tor.
• Connect the pocket tester (W ´ 1) to the
thermo switch 1 as shown.
• Immerse the thermo switch in a container
filled with coolant 2.
NOTE:
Make sure that the thermo switch terminals
do not get wet.
• Place a thermometer 3 in the coolant.
• Slowly heat the coolant, then let it cool to
the specified temperature as indicted in
the table.
• Check the thermo switch for continuity a
the temperatures indicated in the table.
WARNINGWARNING
• Handle the thermo switch with special
care.
• Never subject the thermo switch to
strong shocks. If the thermo switch is
dropped, replace it.
The thermo switch circuit is open and the
radiator fan is off.
õThe thermo switch circuit is closed and the
radiator fan is on.
• Does the thermo switch operate properly
as described above?
Yes ® OK.
No ® Replace.
Test stepCoolant temperature
Continuity
Thermo switch
10 ~ 100 ± 3˚C
(0 ~ 212 ± 37.4˚F)NO
2
More than 105 ± 3˚C
(221 ± 37.4˚C)YES
3*
105 to 100 ˚C
(221 to 212 ˚F)YES
4*
Less than 100 ˚C (212 ˚F)NO
Test steps 1 & 2: Heating phase
Test steps 3* & 4*: Cooling phase
T R..
Thermo switch
23 Nm (2.3 m • kg, 17 ft • lb)
Three bond sealock
® 10

8 - 29
–+ELECELECTRONIC FUEL INJECTION SYSTEM
1Main switch
5Battery
6Main fuse
CCamshaft sensor
DThrottle position sensor
EIntake air pressure sensor
FAtmospheric pressure sensor
GIntake air temperature sensor
HCoolant temperature sensor
IPickup coil
JECU
KCylinder #1-injector 1
LCylinder #2-injector 1
MCylinder #3-injector 1
NCylinder #4-injector 1
OCylinder #1-injector 2
PCylinder #2-injector 2
QCylinder #3-injector 2
RCylinder #4-injector 2
XFall detection switch
YSpeed sensor
yFuel pump
zMain relay
}Engine stop switch
ŒElectronic fuel injection system fuse
£ECU fuse
TROUBLESHOOTING
NOTE:
• Before troubleshooting, remove the following part(-s):
1) bottom cowling
2) front cowling
• Troubleshoot with the following special tool(-s).
The condition code is displayed by the tachometer.
Check the condition code list to
identify the faulty part. Refer to
“ELECTRICAL CONTROL SYS-
TEM”.
In diagnosis mode, select the
appropriate diagnosis code to
check the operation of the faulty
part.Check the
wiring.Replace.
Co, diagnosis switch box
90890-03171
Test coupler adapter
90890-03149
Out of specifi-
cationNo good

8 - 32
–+ELECELECTRICAL CONTROL SYSTEM
Condition code list
NOTE:
* This condition code is also displayed in the following cases:
- when the starter switch is held down for more than 4 seconds, causing the warning
light to flash
- when the ignition circuit cut-off system stops the engine or prevents it from starting
** This condition code is also displayed when the engine is operated at 5,000 r/min for at
least 30 seconds with the rear wheel at standstill.
*** This condition code is also displayed when the engine stop switch is turned to “ ”
while riding with the transmission in gear. Condition
codeCircuit Defect(s) System response
11 Camshaft sensor • No incoming sig-
nalThe ECU pairs the ignition of cyl-
inders #1 and #4 and cylinders #2
and #3. The motorcycle can be
ridden.
12* Pickup coil • No incoming sig-
nalThe motorcycle cannot be ridden.
13 Intake air pressure
sensor• Disconnected
• Short-circuitThe ECU stays set to an intake air
pressure of 760 mm Hg (29.9 in Hg).
The motorcycle can be ridden.
14 Intake air pressure
sensor hose and
negative pressure
hose• Improper connec-
tion
• Bending
15 Throttle position
sensor• Disconnected
• Short-circuitThe ECU stays set to a wide throt-
tle opening.
The motorcycle can be ridden.
16 Throttle position
sensor• Locked
21 Coolant tempera-
ture sensor• Disconnected
• Short-circuitThe ECU stays set to a coolant
temperature of 80˚C (176˚F).
The motorcycle can be ridden.
22 Intake air tempera-
ture sensor• Disconnected
• Short-circuitThe ECU stays set to an intake air
temperature of 40˚C (104˚F).
The motorcycle can be ridden.
23 Atmospheric pres-
sure sensor• Disconnected
• Short-circuitThe ECU stays set to an atmo-
spheric pressure of 760 mm Hg
(29.9 in Hg).
The motorcycle can be ridden.
41 Fall detection
switch• Disconnected The main relay stays switched off.
The motorcycle cannot be ridden.
42** Speed sensor • Incorrect signal The ECU stays set to 6th gear.
The motorcycle can be ridden.
43*** Monitored voltage • Incorrect The ECU stays set to a monitored
voltage of 12 V.
The motorcycle can be ridden.
44 ROM operation • CO emission
adjustment errorThe CO emission adjustment is
set to 0.

8 - 36
–+ELECELECTRICAL CONTROL SYSTEM
Diagnosis code list
Diagnosis
codeInspected item System responseTachometer display
(0 ~ 10,000 r/min)
00 — — —
01 Voltage The tachometer displays the volt-
age ´ 500.
Example:
If the voltage is 12.5 V, the tachome-
ter displays 12.5 ´ 500 = 6,250 r/min.0 r/min (0 V) –
10,000 r/min (20 V)
02 Atmospheric
pressureThe tachometer displays the atmo-
spheric pressure sensor signal.
Example:
If the atmospheric pressure is 760
mm Hg (29.9 in Hg), the tachometer
displays 8,000 r/min.
03 Intake air pres-
sureThe tachometer displays the differ-
ence between the minimum intake
air pressure sensor signal and the
atmospheric pressure sensor signal
after the main switch is turned to
“ON” in the diagnosis mode.0 r/min (0 mm Hg)
– 1,000 r/min
(100 mm Hg)
04 Throttle position
sensorThe tachometer displays the throttle
position sensor signal.1,300 r/min (0.68 V) –
5,900 r/min (2.93 V)
05 Throttle position
sensorThe tachometer displays the mini-
mum throttle position sensor signal.5,500 r/min (0.68 V) –
10,000 r/min (1.25 V)
06 Intake air temper-
atureThe tachometer displays the intake
air temperature signal.4,800 r/min (20˚C) –
5,700 r/min (30˚C)
07 Coolant tempera-
tureThe tachometer displays the coolant
temperature sensor signal.4,900 r/min (20˚C) –
9,200 r/min (100˚C)
08 Speed sensor The tachometer displays the speed
sensor signal when the rear wheel is
rotated by hand.0 –
09 Fall detection
switchThe tachometer displays whether
the fall detection switch is on or
whether it is off or disconnected.0 r/min (on), 8,000 r/
min (off) or 10,000 r/
min (disconnected)
10 Sidestand switch The tachometer displays whether
the sidestand switch is on or off.
The tachometer displays 0 r/min
when the sidestand is down (switch
on) and 10,000 r/min when the side-
stand is up (switch off).0 r/min (on) or
10,000 r/min (off)
11 — — —

YZF-R7 WIRING DIAGRAM
1
Main switch

2
Rectifier/regulator

3
Generator

4
Backup fuse (odometer)

5
Battery

6
Main fuse

7
Starter relay

8
Starter motor

9
Diode

0
Relay unit

A
Diode

B
Sidestand switch

C
Camshaft sensor

D
Throttle position sensor

E
Intake air pressure sensor

F
Atmospheric pressure sensor

G
Intake air temperature sensor

H
Coolant temperature sensor

I
Pickup coil

J
ECU

K
Cylinder #1 - injector 1

L
Cylinder #2 - injector 1

M
Cylinder #3 - injector 1

N
Cylinder #4 - injector 1

O
Cylinder #1 - injector 2

P
Cylinder #2 - injector 2

Q
Cylinder #3 - injector 2

R
Cylinder #4 - injector 2

S
Cylinder #1 - ignition coil

T
Cylinder #2 - ignition coil

U
Cylinder #3 - ignition coil

V
Cylinder #4 - ignition coil

W
CDI unit

X
Fall detection switch

Y
Speed sensor

Z
Neutral switch

[
Meter assembly

\
Fuel level indicator light

]
Warning light (oil level indicator)

^
Neutral indicator light

a
Tachometer

b
Combination meter

c
Warning light (coolant temperature indicator)
d
High beam indicator light
e
Turn signal indicator light
f
Meter light
gWarning light (engine trouble indicator)
hOil level switch
i
Horn
jHeadlight
kRear turn signal light (right)
lRear turn signal light (left)
mFront turn signal light (right)
nFront turn signal light (left)
oTail/brake light
pRear brake light switch
q
Left handlebar switch
rClutch switch
sLights switch
t
Pass switch
uDimmer switch
vTurn signal switch
wHorn switch
xTurn signal relay
yFuel pump
zMain relay
{
Right handlebar switch|Front brake light switch
}Engine stop switch
~Start switch
Œ
Electronic fuel injection system fuseCYCLELOCK Signaling system fuse
¢Headlight fuse£
ECU fuse¤Radiator fan motor fuse
¥Thermo switch
¦Radiator fan motor
COLOR CODE
B ............ black
Br ........... brown
Ch .......... chocolate
Dg .......... dark green
G ............ green
Gy .......... gray
L ............ blue
Lg .......... light green
O ............ orange
P ............ pink
R ............ red
Sb .......... sky blue
W ........... white
Y ............ yellow
B/L ......... black/blue
B/R ......... black/red
B/W ....... black/white
B/Y ......... black/yellow
Br/G ....... brown/green
Br/L ........ brown/blue
Br/R ....... brown/red
Br/W ...... brown/white
G/B ........ green/black
G/R ........ green/red
G/W ....... green/white
G/Y ........ green/yellow
Gy/B ...... gray/black
Gy/G ...... gray/green
Gy/R ...... gray/red
L/B ......... blue/black
L/G ......... blue/green
L/R ......... blue/red
L/W ........ blue/white
L/Y ......... blue/yellow
Lg/R ....... light green/red
Lg/Y ....... light green/yellow
O/B ........ orange/black
O/G ........ orange/green
P/B ......... pink/black
P/L ......... pink/blue
P/W ........ pink/white
R/B ......... red/black
R/G ........ red/green
R/L ......... red/blue
R/W ....... red/white
R/Y ......... red/yellow
W/B ....... white/black
W/G ....... white/green
W/L ........ white/blue
W/Y ....... white/yellow
Y/B ......... yellow/black
Y/G ........ yellow/green
Y/L ......... yellow/blue
Y/R ......... yellow/rod