1999 YAMAHA YZF-R7 ESP

8 - 36
–+ELECELECTRICAL CONTROL SYSTEM
Diagnosis code list
Diagnosis
codeInspected item System responseTachometer display
(0 ~ 10,000 r/min)
00 — — —
01 Voltage The tachometer displays the volt-
age ´ 500.
Example:
If the voltage is 12.5 V, the tachome-
ter displays 12.5 ´ 500 = 6,250 r/min.0 r/min (0 V) –
10,000 r/min (20 V)
02 Atmospheric
pressureThe tachometer displays the atmo-
spheric pressure sensor signal.
Example:
If the atmospheric pressure is 760
mm Hg (29.9 in Hg), the tachometer
displays 8,000 r/min.
03 Intake air pres-
sureThe tachometer displays the differ-
ence between the minimum intake
air pressure sensor signal and the
atmospheric pressure sensor signal
after the main switch is turned to
“ON” in the diagnosis mode.0 r/min (0 mm Hg)
– 1,000 r/min
(100 mm Hg)
04 Throttle position
sensorThe tachometer displays the throttle
position sensor signal.1,300 r/min (0.68 V) –
5,900 r/min (2.93 V)
05 Throttle position
sensorThe tachometer displays the mini-
mum throttle position sensor signal.5,500 r/min (0.68 V) –
10,000 r/min (1.25 V)
06 Intake air temper-
atureThe tachometer displays the intake
air temperature signal.4,800 r/min (20˚C) –
5,700 r/min (30˚C)
07 Coolant tempera-
tureThe tachometer displays the coolant
temperature sensor signal.4,900 r/min (20˚C) –
9,200 r/min (100˚C)
08 Speed sensor The tachometer displays the speed
sensor signal when the rear wheel is
rotated by hand.0 –
09 Fall detection
switchThe tachometer displays whether
the fall detection switch is on or
whether it is off or disconnected.0 r/min (on), 8,000 r/
min (off) or 10,000 r/
min (disconnected)
10 Sidestand switch The tachometer displays whether
the sidestand switch is on or off.
The tachometer displays 0 r/min
when the sidestand is down (switch
on) and 10,000 r/min when the side-
stand is up (switch off).0 r/min (on) or
10,000 r/min (off)
11 — — —

8 - 37
–+ELECELECTRICAL CONTROL SYSTEM
12 Main relay CO, diagnosis switch box method
Within one second after the
MODE switch is released, the
main relay is switched on once
every second for the next five
seconds. During this time, the
warning light lights up as long as
the relay is switched on.
Test coupler adapter method
Within one second after the
engine stop switch is turned to
“ ”, the main relay is switched
off, then on again. The warning
light lights up while the relay is
switched off.
13 Ignition coil for
cylinder #1CO, diagnosis switch box method
Within one second after the
MODE switch is released, the
ignition coil for the selected cylin-
der is operated once every sec-
ond for the next five seconds.
During this time, the warning
light lights up for 0.5 second
once every second.
Test coupler adapter method
Within one second after the
engine stop switch is turned to
“ ”, the ignition coil for the
selected cylinder is operated
once every second for the next
five seconds. During this time,
the warning light lights up for 0.5
second once every second. 14 Ignition coil for
cylinder #2
15 Ignition coil for
cylinder #3
16 Ignition coil for
cylinder #4 Diagnosis
codeInspected item System responseTachometer display
(0 ~ 10,000 r/min)

8 - 38
–+ELECELECTRICAL CONTROL SYSTEM
17 Injector 1 for cyl-
inder #1CO, diagnosis switch box method
Before selecting a code, discon-
nect the fuel pump coupler from
the wire harness.
Within one second after the
MODE switch is released, the
main relay is turned on, and the
selected injector is operated once
every second for the next five
seconds. During this time, the
warning light lights up for 0.5
second once every second.
Test coupler adapter method
Within one second after the
engine stop switch is turned to
“ ”, the selected injector is
operated for once every second
for the next five seconds. During
this time, the warning light lights
up for 0.5 second once every sec-
ond. 18 Injector 1 for cyl-
inder #2
19 Injector 1 for cyl-
inder #3
20 Injector 1 for cyl-
inder #4
21 Injector 2 for cyl-
inder #1
22 Injector 2 for cyl-
inder #2
23 Injector 2 for cyl-
inder #3
24 Injector 2 for cyl-
inder #4
25 ~ 28 — — —
29 Condition code
record of mal-
functionsThe condition code of any fixed mal-
function is recorded in the ROM and
displayed by the tachometer. Refer
to the condition code list in “USER
MODE” for details on the condition
codes.Condition codes 11
– 44
30 ROM (Clearing
the condition
code record)Selecting this diagnosis code clears
the condition code record of mal-
functions stored in the ROM.
If an error has occurred in a sensor
signal, it was recorded in the ROM
and the tachometer displays 10,000
r/min. If no error has occurred, the
tachometer displays 0 r/min.
CO, diagnosis switch box method
Press the UP switch eight times
within four seconds to clear the con-
dition code record from the ROM.
Test coupler adapter method
Remove the rear cowling.
Disconnect the relay unit coupler
from the relay unit.
Press the start switch ten times
within four seconds to clear the con-
dition code record from the ROM.0 r/min (no error) or
10,000 r/min (errors)
When the error
record is cleared, 0
r/min is displayed.
31 ROM program
versionThe version number of the ROM pro-
gram is displayed in the tachometer. Diagnosis
codeInspected item System responseTachometer display
(0 ~ 10,000 r/min)