1999 SUZUKI GRAND VITARA hub

YH4
GRAND
VITARA
1. Steering column
2. Steering lock
1. Center punch (with sharp point)
2. Steering lock mounting bolt
1. Steering column
2. Steering shaft
3C-10 STEERING WHEEL AND COLUMN
STEERING LOCK ASSEMBLY (IGNITION
SWITCH)
REMOVAL
1) Remove steering column. Refer to ªSTEERING COLUMNº in
this section.
2) Using center punch as shown, loosen and remove steering lock
mounting bolts.
NOTE:
Use care not to damage aluminum part of steering lock
body with center punch.
3) Turn ignition key to ªACCº or ªONº position and remove steering
lock assembly from steering column.
INSTALLATION
1) Position oblong hole of steering shaft in the center of hole in col-
umn.
2) Turn ignition key to ªACCº or ªONº position and install steering
lock assembly onto column.
3) Now turn ignition key to ªLOCKº position and pull it out.
4) Align hub on lock with oblong hole of steering shaft and rotate
shaft to assure that steering shaft is locked.
5) Tighten new bolts until head of each bolt is broken off.
6) Turn ignition key to ªACCº or ªONº position and check to be sure
that steering shaft rotates smoothly. Also check for lock opera-
tion.
7) Install steering column. Refer to ªSTEERING COLUMNº in this
section.

YH4
GRAND
VITARA
3C1-14 AIR BAG STEERING WHEEL AND COLUMN
1. Steering column
2. Steering lock 1
2
1. Center punch (with sharp point)
2. Steering lock mounting bolt
1. Steering column
2. Steering shaft
STEERING LOCK ASSEMBLY (IGNITION
SWITCH)
REMOVAL
1) Remove steering column. Refer to ªSTEERING COLUMNº in
this section.
2) Using center punch as shown, loosen and remove steering lock
mounting bolts.
NOTE:
Use care not to damage aluminum part of steering lock
body with center punch.
3) Turn ignition key to ªACCº or ªONº position and remove steering
lock assembly from steering column.
INSTALLATION
1) Position oblong hole of steering shaft in the center of hole in col-
umn.
2) Turn ignition key to ªACCº or ªONº position and install steering
lock assembly onto column.
3) Now turn ignition key to ªLOCKº position and pull it out.
4) Align hub on lock with oblong hole of steering shaft and rotate
shaft to assure that steering shaft is locked.
5) Tighten new bolts until head of each bolt is broken off.
6) Turn ignition key to ªACCº or ªONº position and check to be sure
that steering shaft rotates smoothly. Also check for lock opera-
tion.
7) Install steering column. Refer to ªSTEERING COLUMNº in this
section.

YH4
GRAND
VITARA
3D
FRONT SUSPENSION 3D-1
GENERAL DESCRIPTION3D- 2 . . . . . . . . . . . . . .
DIAGNOSIS3D- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnosis Table 3D- 3. . . . . . . . . . . . . . . . . . . . . .
Stabilizer Bar and Bushing Check 3D- 3. . . . . .
Strut Damper and / or Coil Spring Check 3D- 3. .
Suspension Arm / Knuckle Check 3D- 3. . . . . . . .
Suspension Control Arm Joint Check 3D- 4. . . .
Suspension Control Arm Bushing Check 3D- 4.
Wheel Disc, Nut & Bearing Check 3D- 4. . . . . .
ON-VEHICLE SERVICE3D- 5 . . . . . . . . . . . . . . . . Stabilizer Bar / Bushings 3D- 5. . . . . . . . . . . . . . .
Strut Damper 3D- 6. . . . . . . . . . . . . . . . . . . . . . . .
Coil Spring 3D- 8. . . . . . . . . . . . . . . . . . . . . . . . . .
Bump Stopper / Spring Rubber Seat 3D-11. . . . .
Wheel Hub (Included Wheel Bearing) 3D-12. . .
Knuckle / Wheel Spindle 3D-17. . . . . . . . . . . . . . . .
Suspension Control Arm / Bushings 3D-21. . . . . .
TIGHTENING TORQUE
SPECIFICATIONS3D-23 . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS3D-24 . . . . . .
SPECIAL TOOLS3D-25 . . . . . . . . . . . . . . . . . . . . . .
SECTION 3D
FRONT SUSPENSION
CAUTION:

All front suspension fasteners are an important attaching part in that it could affect the performance
of vital parts and systems, and / or could result in major repair expense. They must be replaced with
one of the same part number or with an equivalent part if replacement becomes necessary. Do not
use a replacement part of lesser quality or substitute design. Torque values must be used as specified
during reassembly to assure proper retention of this part.

Never attempt to heat, quench or straighten any front suspension part. Replace it with a new part or
damage to the part may result.
CONTENTS

YH4
GRAND
VITARA
3D-4 FRONT SUSPENSION
SUSPENSION CONTROL ARM JOINT CHECK
1) Check for smoothness of rotation.
2) Inspect ball stud for damage.
3) Inspect dust cover for damage.
Replace any parts found defective in steps 1) ± 3).
SUSPENSION CONTROL ARM BUSHING
CHECK
Inspect for damage, wear or deterioration.
WHEEL DISC, NUT & BEARING CHECK
1) Inspect each wheel disc for dents, distortion and cracks.
Disc in badly damaged condition must be replaced.
2) Check wheel nuts for tightness and retighten them to specifica-
tion as necessary.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
3) Check wheel bearing for wear. After retightening lock nut to spe-
cified torque, apply dial gauge to wheel hub center and measure
thrust play.
Thrust play limit: 0.05 mm (0.002 in.)
When measurement exceeds limit, replace bearing.
4) By rotating wheel actually, check wheel bearing for noise and
smooth rotation. If defective, replace bearing.

YH4
GRAND
VITARA
FRONT SUSPENSION 3D-9
1. Coil spring
8) Remove stabilizer bar, refer to steps 2) to 5) of item STABILIZ-
ER BAR / BUSHINGS REMOVAL in this section.
9) Disconnect tie rod end from knuckle by using puller.
10) Support lower arm, using jack as shown.
11) Remove strut bracket bolts.
12) Remove ball stud castle nut.
13) Using puller, disconnect knuckle from ball stud.
14) Remove knuckle and wheel hub comp, while lowering jack.
15) Remove coil spring.

YH4
GRAND
VITARA
3D-10 FRONT SUSPENSION
ªaº < ªbº
1. Circlip
2. Large diameter
1. Axle shaft drive flange
2. Bolt 1. Spring seat
Bottom
INSTALLATION
Reverse removal procedure to install coil spring.
NOTE:
Upper and lower diameters of coil spring are different.
Bring larger diameter end at bottom and set its open end in
place on spring seat.

Be sure to use specified torque for tightening each fastener.

Refer to torque specification chart at the end of this section.

As for ball stud nut, be sure to insert split pin and bend it after tight-
ening it.

Tighten tie-rod end nut with pushing ball stud to upper side so as
not ball stud to be rotated.

For 4WD vehicle
Apply lithium grease to front drive shaft washer and front wheel
spindle outer.
ªAº: Grease 99000-25010

For 4WD vehicle
When installing circlip to drive shaft, utilize screw hole in drive
shaft to pull it out and bring large diameter of circlip at right as
shown.

For 4WD vehicle
When installing axle shaft drive flange to wheel hub, apply sealant
to mating surface of axle shaft drive flange and tighten flange bolt
to specified torque.
ªAº: Sealant 99000-31090
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)

YH4
GRAND
VITARA
3D-12 FRONT SUSPENSION
1. Lock washer
2. Screws 1. Axle shaft drive flange
WHEEL HUB (INCLUDED WHEEL BEARING)
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove axle shaft drive flange (4WD vehicle) or hub cap (2WD
vehicle).
3) If equipped with ABS, remove wheel speed sensor from knuckle
and harness clamp from strut.
4) Remove caliper bolt and suspend caliper.
CAUTION:
Hang removed caliper with a wire hook or the like so as to
prevent brake hose from bending and twisting excessively
or being pulled.
Don't operate brake pedal with pads removed.
5) Remove brake disc.
NOTE:
If brake disc can not be removed by hand, use 8 mm bolts as
shown.
6) Remove front wheel bearing lock washer by loosening 4 screws.
7) Remove front wheel bearing lock nut by using special tool.
Special Tool
(A): 09951-16050
8) Remove front wheel bearing washer.
9) Remove wheel hub component by hand.

YH4
GRAND
VITARA
1. Sensor rotor
2. Wheel hub
3. Vise
4. Flat end rod
1. Bearing lock washer
2. Screw
3. Bearing lock nut
4. Wheel bearing washer
5. Wheel hub component
6. Bolt
1. Oil hydraulic press
2. Hub bolt
FRONT SUSPENSION 3D-13
NOTE:
If wheel hub can not be removed by hand, use special tools
as shown.
Special Tool
(B): 09943-35512
(C): 09942-15510
CAUTION:
If wheel bearing inner race remains on wheel spindle
when removing wheel hub, which means break of wheel
bearing, replace wheel hub component (included wheel
bearing).
10) Remove sensor rotor from wheel hub as shown (if equipped
with ABS).
CAUTION:

Pull out sensor rotor from wheel hub gradually and
evenly.

Do not reuse sensor rotor once removed.
Be sure to new sensor rotor when installing.
11) Remove hub bolts from hub.
INSTALLATION
1) Insert new stud in hub hole. Rotate stud slowly to assure serra-
tions are aligned with those made by original bolt.