1999 SUZUKI GRAND VITARA Wiring harness

YH4
GRAND
VITARA
0A-16 GENERAL INFORMATION

Poor terminal-to-wire connection.
Check each wire harness in problem circuits for poor connection
by shaking it by hand lightly. If any abnormal condition is found,
repair or replace.

Wire insulation which is rubbed through, causing an intermittent
short as the bare area touches other wiring or parts of the vehicle.

Wiring broken inside the insulation. This condition could cause
continuity check to show a good circuit, but if only 1 or 2 strands
of a multi-strand-type wire are intact, resistance could be far too
high.
If any abnormality is found, repair or replace.
PRECAUTION FOR INSTALLING MOBILE
COMMUNICATION EQUIPMENT
When installing mobile communication equipment such as CB (Citi-
zens-Band)-radio or cellular-telephone, be sure to observe the fol-
lowing precautions.
Failure to follow cautions may adversely affect electronic control
system.

Keep the antenna as far away as possible from the vehicle's elec-
tronic control unit.

Keep the antenna feeder more than 20 cm (7.9 in.) away from
electronic control unit and its wire harnesses.

Do not run the antenna feeder parallel with other wire harnesses.

Confirm that the antenna and feeder are correctly adjusted.

YH4
GRAND
VITARA
1A-18 HEATER AND VENTILATION
11) Remove heater core pipe clamps (1) and grommet (2).
12) Pull out heater core (1) from unit (2).
INSTALLATION
1) Install heater unit by reversing removal procedure, noting the
following items.

When installing each part, be careful not to catch any cable or
wiring harness.

When installing steering column assembly, refer to STEER-
ING COLUMN INSTALLATION in Section 3C or 3C1.
2) Install control cables. (Refer to HEATER CONTROL CABLES in
this section.)
3) Fill engine coolant to radiator.
4) Enable air bag system, if equipped. Refer to ENABLING AIR
BAG SYSTEM in Section 10B.
5) Evacuate and charge system. Refer to items EVACUATING
SYSTEM and PROCEDURE OF CHARGING in Section 1B.

YH4
GRAND
VITARA
1. Transmission
2. Breather clamp
3. Breather hose
4. Wiring harness clamp
5. Intake manifold
MANUAL TRANSMISSION (TYPE 1) 7A-9
DISMOUNTING OF TRANS. UNIT
IN CABIN
Remove transmission shift control lever (refer to page 7A-4) and
transfer shift control lever knob.
IN ENGINE ROOM
1) Disconnect negative (±) cable of battery.
2) Remove breather hose from clamp at the rear end of cylinder
head.
3) Remove starting motor fixing bolts and nut and then remove
starter.
4) Remove transmission fastening bolts.

YH4
GRAND
VITARA
1. Transmission assembly
2. Transfer assembly
3. Wiring harness4. Breather hose
5. Gear shift lever case
6. Bolt
7. Bolt
MANUAL TRANSMISSION (TYPE 1) 7A-11
10) Remove wiring harness and breather hose.
11) Separate gear shift lever case and transfer assembly (or exten-
sion case: 2WD model) from transmission.

YH4
GRAND
VITARA
7B1
AUTOMATIC TRANSMISSION (4 A / T) 7B1-1
GENERAL DESCRIPTION7B1- 3 . . . . . . . . . . . . . .
CLUTCH / BRAKE FUNCTIONS 7B1- 5. . . . . . . . .
TABLE OF COMPONENT OPERATION 7B1- 6. . .
ELECTRONIC SHIFT CONTROL
SYSTEM 7B1- 7. . . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSIS7B1-17 . . . . . . . . . . . . . . . . . . . . . . . . . .
PRECAUTION IN DIAGNOSING
TROUBLE 7B1-20. . . . . . . . . . . . . . . . . . . . . . . . . .
AUTOMATIC TRANSMISSION
DIAGNOSTIC FLOW TABLE 7B1-21. . . . . . . . . .
Customer Problem Inspection Form 7B1-23. . .
Malfunction Indicator lamp (MIL)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
ªO / D OFFº Lamp Check 7B1-24. . . . . . . . . . . . .
ªPOWERº Lamp Check 7B1-24. . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Check 7B1-24. . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC)
Clearance 7B1-24. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Code (DTC) Table7B1-24 . . .
Fail-Safe Table 7B1-25. . . . . . . . . . . . . . . . . . . . .
Visual Inspection 7B1-26. . . . . . . . . . . . . . . . . . .
A / T Basic Check 7B1-27. . . . . . . . . . . . . . . . . . .
Trouble Diagnosis Table 1 7B1-28. . . . . . . . . . .
Trouble Diagnosis Table 2 7B1-28. . . . . . . . . . . Trouble Diagnosis Table 3 7B1-29. . . . . . . . . . .
Scan Tool Data 7B1-30. . . . . . . . . . . . . . . . . . . . .
Inspection of PCM and Its Circuit 7B1-30. . . . .
Wire Harness and Connectors 7B1-30. . . . . . . .
Diagnostic Flow Table A-1 7B1-31. . . . . . . . . . .
Diagnostic Flow Table A-2 7B1-33. . . . . . . . . . .
Table B-1 ªO / D OFFº Light Circuit
Check 7B1-35. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-2 ªO / D OFFº Light Circuit
Check 7B1-36. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-3 ªPOWERº Light Circuit
Check 7B1-37. . . . . . . . . . . . . . . . . . . . . . . . . . .
Table B-4 ªPOWERº Light Circuit
Check 7B1-38. . . . . . . . . . . . . . . . . . . . . . . . . . .
DTC P0705 Transmission Range
Sensor (Switch) Circuit Malfunction 7B1-39. .
DTC P0715 Input / Turbine Speed
Sensor Circuit Malfunction 7B1-42. . . . . . . . . .
DTC P0720 Output Speed Sensor
Circuit Malfunction 7B1-44. . . . . . . . . . . . . . . . .
DTC P0741 TCC Solenoid Valve
Performance or Stuck Off 7B1-46. . . . . . . . . . .
DTC P0743 TCC Solenoid Electrical 7B1-47. .
DTC P0751 Shift Solenoid Valve-A (#1)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
DTC P0756 Shift Solenoid Valve-B (#2)
Performance or Stuck Off 7B1-49. . . . . . . . . . .
SECTION 7B1
AUTOMATIC TRANSMISSION
(4 A
/
T)
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System:

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CONTENTS

YH4
GRAND
VITARA
7B1-74 AUTOMATIC TRANSMISSION (4 A / T)
1. Boot No.2
2. Boot cover
1. Boot clamp
2. Boot No.1
3. Gear shift control lever
1. Boot No.2
2. Transfer shift control
lever
3. Transfer shift lever case4. Transfer shift control
case cover
5. Boot No.1
1. A / T throttle cable
2. Adjusting nut
3. Lock nut
G16 / J20 H25
DISMOUNTING OF TRANSMISSION (WITH
TRANSFER IF EQUIPPED)
IN CABIN
1) Remove console box.
NOTE:
To remove clip, push in its center pin first.
2) Remove boot cover and boot No.2. (if equipped)
3) Remove boot clamp and then remove boot No.1 from transfer
gear shift lever case. (if equipped)
4) With transfer shift control case cover pushed down with fingers,
turn it to counterclockwise and take out shift control lever. (if
equipped)
IN ENGINE ROOM
1) Remove battery, dipstick and oil filler tube.
2) Disconnect A
/
T throttle cable from throttle cam and bracket.
3) Remove starter motor. But don't disconnect its wiring harness.
4) Remove transmission to engine bolt and nut.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-77
ªAº, (d)
1. Drive plate
2. Torque converter
3. Case right stiffener (if equipped)
4. Automatic transmissionTightening torque
(a): 50 N´m
5.0 kg-m
36.5 lb-ft
(b): 65 N´m
6.5 kg-m
47.0 lb-ft
(c): 85 N´m
8.5 kg-m
61.5 lb-ft
(d): 78 N´m
7.8 kg-m
56.5 lb-ft
1. Automatic transmission
2. Transfer (4WD)
3. Engine rear mounting
4. Engine rear mounting member Tightening torque
(a): 50 N´m (5.0 kg-m, 36.5 lb-ft) ªAº: Sealant 99000-31110
REMOUNTING
WARNING:
When moving transmission assembly with torque convert-
er equipped in it, be sure to keep it horizontal. Tilting it with
its front facing down may allow converter to fall off. Where-
by an injury may result.
For remounting, reverse dismounting procedure. Use specified
torque as given below and left.
Tightening torque
N.mkg-mlb-ft
Exhaust No.1 pipe to manifold
bolts or nuts505.036.5
Muffler to exhaust No.2 pipe
nuts606.043.5
Universal joint flange bolts and
nuts505.036.5

Oil filler tube bolts

Select cable bracket bolts232.317.0

Clamp wiring harness and hoses securely.

Refer to ªSelect Cableº section for adjusting procedure of select
cable.

Refer to ªA / T Throttle Cableº section for tuning of A / T throttle
cable.

Follow fluid level check procedure for refilling automatic transmis-
sion fluid and its level adjusting.

Connect battery, and confirm that engine and transmission func-
tion acceptably.

When remounting drive plate, use specified bolts.

YH4
GRAND
VITARA
8
BODY ELECTRICAL SYSTEM 8-1
SECTION 8
BODY ELECTRICAL SYSTEM
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
WIRING SYSTEM
(Harnesses, Connectors, Fuses, Relay, Switches, Grounds, System Circuit Diagram)Section 8A . . . . . . .
LIGHTING SYSTEMSection 8B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
INSTRUMENTATION AND DRIVER INFORMATIONSection 8C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
WINDOWS, MIRRORS, SECURITY AND LOCKSSection 8D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
IMMOBILIZER CONTROL SYSTEMSection 8F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CONTENTS
GENERAL DESCRIPTION8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cautions in Servicing8-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Symbols and Marks8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations8-4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wiring Color Symbols8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Joint Connector8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuse Box and Relay8-5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Diagram8-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .