1999 SUZUKI GRAND VITARA 100

YH4
GRAND
VITARA
0B-2 MAINTENANCE AND LUBRICATION
MAINTENANCE SCHEDULE
MAINTENANCE SCHEDULE UNDER NORMAL DRIVING CONDITIONS
Interval:
This interval should be judged by
This table includes services as scheduled up to 90,000 km
(54,000 miles) mileage. Beyond 90,000 km (54,000 miles), carry
out the same services at the same intervals respectively.
This interval should be judged by
odometer reading or months,Km (x 1,000)153045607590g
whichever comes first.Miles (x 1,000)91827364554
Months122436486072
ENGINE
1-1. Drive beltV-beltIRIRIR
V-rib belt (Flat type)±±I±±R
1-2. Camshaft timing belt (G16 engine only)Replace every 100,000 km or
60,000 miles
1-3. Valve lash (clearance)G16 engine only±I±I±I
1-4. Engine oil and
oil filterJ20 / H25 engines
G16 engine with HO2S (SG, SH, SJ)RRRRRR
G16 engine with HO2S (SE, SF),
G16 engine without HO2SReplace every 10,000 km (6,000 miles)
or 8 months
1-5. Engine coolant±±R±±R
1-6. Exhaust system±I±I±I
IGNITION SYSTEM
2-1. Spark plugs
Wh
Vehicle without
HO2S
Nickel plug±R±R±R
When
unleaded
HO2SIridium plug±±±R±±unleaded
fuel isVehicle with
HO2S
Nickel plug±±R±±Rfuel is
usedHO2SIridium plugReplace every 105,000 km or 63,000
miles
When leaded fuel is used, refer to ªSevere Driving Conditionº schedule
FUEL SYSTEM
3-1. Air cleaner filterIIRIIR
3-2. Fuel lines and connections±I±I±I
3-3. Fuel filterReplace every 105,000 km or 63,000
miles
3-4. Fuel tank±±I±±I
EMISSION CONTROL SYSTEM
4-1. Crankcase ventilation hoses and connections
(Vehicle without HO2S)±±I±±I
4-2. PCV valveVehicle without HO2S±±I±±I
Vehicle with HO2S±±±±±I
4-3. Fuel evaporative emission
tl t
Vehicle without HO2S±I±I±I
control systemVehicle with HO2S±±±±±I
NOTES:

ªRº : Replace or change

ªIº : Inspect and correct, replace or lubricate if necessary

For Item 1-2. Camshaft timing belt: This belt may be replaced every 90,000 km (54,000 miles) according
to customer's maintenance convenience.

For Sweden, item 2-1, 4-2 and 4-3 should be performed by odometer reading only.

For Item 2-1. Spark plugs, replace every 50,000 km if the local law requires.

Nickel spark plug: BKR6E-11 or K20PR-U11

Iridium spark plug: IFR6E11 or SK20PR-A11 for G16 engine, IFR5J11 or SK16PR11 for J20 / H25 engines

YH4
GRAND
VITARA
1. Crankshaft pulley
2. Water pump pulley
3. 100 N, 10 kg or 22 lb
G16
H25
MAINTENANCE AND LUBRICATION 0B-5
MAINTENANCE SERVICE
ENGINE
ITEM 1-1
Drive Belt Inspection and Replacement
WARNING:
All inspection and replacement are to be performed with
ENGINE NOT RUNNING.
Water pump and generator drive belt (G16 and H25 engines)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace.
Check belt for tension.
Water pump and generator belt tension
ªaº: 6 ± 8 mm (0.24 ± 0.32 in.) deflection for G16, 9 ± 11 mm
(0.35 ± 0.43 in.) deflection for H25 under 100 N, 10 kg or
22 lb pressure
NOTE:
When replacing belt with a new one, adjust belt tension to
5 ± 6 mm (0.20 ± 0.24 in.) for G16, 7 ± 9 mm (0.28 ± 0.35 in.)
for H25.
3) If belt is too tight or too loose, adjust it to specification by adjust-
ing alternator position.
4) Tighten alternator adjusting bolt and pivot bolts.
5) Connect negative cable to battery.
Replacement
Replace belt. Refer to Section 6B for replacement procedure of
pump belt.

YH4
GRAND
VITARA
J20
J20
1. 100 N, 10 kg or 22 lb
2. Fan pulley3. Crankshaft pulley
4. Adjusting and pivot bolt
0B-6 MAINTENANCE AND LUBRICATION
Water pump, generator, power steering and / or A / C
compressor (if equipped) drive belt (J20 engine)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any of above conditions are found, replace.
Also, check belt for tension.
Tension indicator ªBº should be the right of indicator ªAº as
shown in figure. If indicator ªBº is found to the left of indicator ªAº,
replace generator belt.
Replacement
Replace belt referring to Section 6H for replacement procedure of
generator drive belt.
Engine cooling fan drive belt (J20 engine)
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace. Check belt for tension.
Cooling fan belt tension
ªaº: 5 ± 7 mm (0.20 ± 0.27 in.) deflection under 100 N, 10 kg
or 22 lb pressure.
NOTE:
When replacing belt with a new one, adjust belt deflection
to 4 ± 5 mm (0.16 ± 0.19 in.).
3) If the belt is too tight or too loose, adjust it to specification by ad-
justing cooling fan pulley position.
4) Tighten adjusting bolt and pivot bolt.
5) Connect negative cable at battery.
Replacement
Replace belt referring to Section 6B for replacement procedure of
cooling fan drive belt.

YH4
GRAND
VITARA
G16 with P / S
G16 with P / S and A / C
H25 with P / S
H25 with P / S and A / C
1. Crankshaft pulley
2. P / S pump pulley
3. A / C compressor pulley
(if equipped)4. Tension pulley
5. Tension pulley bolts
MAINTENANCE AND LUBRICATION 0B-7
Power steering pump and / or A / C compressor drive belts (if
equipped) for G16 and H25 engines.
Inspection
1) Disconnect negative cable at battery.
2) Inspect belt for cracks, cuts, deformation, wear and cleanliness.
If any defect exists, replace.
Check belt for tension.
Power steering pump and / or A / C compressor drive belt
tension.
ªaº: 6 ± 9 mm (0.24 ± 0.35 in.) deflection under 100 N, 10 kg
or 22 lb pressure.
ªbº: 4 ± 7 mm (0.16 ± 0.28 in.) deflection under 100 N, 10 kg
or 22 lb pressure.
If belt tension is out of above specification, adjust it referring to
Section 1B or 3B1.
3) Connect negative cable to battery.
Replacement
Replace belt referring to Section 1B or 3B1 for replacement proce-
dure of belt.

YH4
GRAND
VITARA
AIR CONDITIONING (OPTIONAL) 1B-15
AMBIENT TEMPERATURE WITHIN 30 ± 35C (85 ± 95F)
CONDITION
MANIFOLD
GAUGEMPa
(kg/cm2)
(psi)DETAILCAUSECORRECTION
LoHi
0.23 ± 0.35
(2.3 ± 3.5)
(33 ± 50)1.4 ± 1.75
(14 ± 17.5)
(200 ± 249)
Normal condition.ÐÐÐÐ
Negative
pressure0.5 ± 0.6
(5 ± 6)
(71.2 ± 85.3)

The low pressure side
reads a negative pressure,
and the high pressure side
reads an extremely low
pressure.

Presence of frost around
tubing to and from receiver /
dryer and expansion valve.
Dust particles or water
droplets are either stuck or
frozen inside expansion
valve, preventing the
refrigerant from flowing.
Clean expansion valve.
Replace it if it cannot be
cleaned.

Replace receiver / dryer.

Evacuate the A / C
system and recharge
with fresh refrigerant.
Normal:
0.23 ± 0.35
(2.3 ± 3.5)
(33 ± 50)

Abnormal:
Negative
pressureNormal:
1.4 ± 1.75
(14 ± 17.5)
(200 ± 249)

Abnormal:
0.69 ± 0.98
(7 ± 10)
(100 ± 142)
During A / C operation, the
low pressure side
sometimes indicates
negative pressure, and
sometimes normal
pressure. Also high
pressure side reading
fluctuates between the
abnormal and normal
pressure.
Expansion valve is frozen
due to moisture in the
system, and temporarily
shuts off the refrigeration
cycle.
Replace expansion
valve.

Replace receiver / dryer.

Evacuate A / C system
and recharge with fresh
refrigerant.
0.05 ± 0.15
(0.5 ± 1.5)
(4.2 ± 21.3)
0.69 ± 0.98
(7 ± 10)
(100 ± 142)

Both low and high pressure
sides indicate low readings.

Continuous air bubbles are
visible through sight glass.

Output air is slightly cold.
Insufficient refrigerant in
system. (Refrigerant
leaking)
Using a gas leak
detector, check for leaks
and repair as necessary.

Recharge refrigerant to a
specified amount.
If the pressure reading is
almost 0 when the
manifold gauges are
attached, check for any
leaks, repair them, and
evacuate the system.
0.4 ± 0.6
(4 ± 6)
(56.9 ± 85.3)

Pressure on low pressure
side is high.

Pressure on high pressure
side is low.

Both pressure becoming
equal right after A / C is
turned OFF.
Internal leak in compressor.
Inspect compressor and
repair or replace as
necessary.
035 045

High pressure reading on
both low and high pressure
sides.

Air bubbles are not visible
even when engine rpm is
lowered.
Overcharged A / C system.

Faulty condenser cooling
operation.

Faulty condenser fan
operation.
Adjust refrigerant to
specified amount.

Clean condenser.

Inspect and repair
condenser fan.
0.35 ± 0.45(3.5 ± 4.5)
(50 ± 64)
1.96 ± 2.45
(20 ± 25)
(285 ± 355)

High pressure reading on
both low and high pressure
sides.

Low pressure side tubing is
not cold when touched.

Air bubbles are visible
through sight glass.
Presence of air in A / C
system. (Improperly
evacuated)
Replace receiver / dryer.

Inspect quantity of
compressor oil and
presence of
contaminants in oil.

Evacuate system and
recharge with fresh
refrigerant.
0.45 ± 0.55
(4.5 ± 5.5)
(64 ± 78)

High pressure reading on
both low and high pressure
sides.

Large amount of frost or
dew on the low pressure
side tubing.
Faulty expansion valve.

Refrigerant flow is not
regulated properly.
Replace expansion
valve.

YH4
GRAND
VITARA
1. P / S fluid reservoir
2. Attachment
3. Gasket4. Union bolt
5. High pressure side
6. Low pressure side
1. P / S fluid reservoir
2. Gauge valve (open)
3. P / S pump4. P / S gear box
5. High pressure side
6. Low pressure side
3B1-10 POWER STEERING (P / S) SYSTEM
HYDRAULIC PRESSURE IN P / S CIRCUIT
HYDRAULIC PRESSURE CHECK
1) After cleaning joint of high pressure hose and P / S pump thor-
oughly, disconnect hose from pump and install special tool (oil
pressure gauge, attachment and hose).
Tighten each flare nut to specified torque.
CAUTION:
Take care not to cause damage to A / C condenser during
service operation, if equipped.
Special Tool
(A): 09915-77410 (Oil pressure gauge)
(B): 09915-77420
2) Check each connection for fluid leakage and bleed air.
Refer to ªAIR BLEEDING PROCEDUREº in this section.
3) With engine idling, turn steering wheel and warm up engine till
temperature of fluid in P/S fluid reservoir rises to 50 ± 60
C (122
± 140
F).
4) Check back pressure by measuring hydraulic pressure with en-
gine idling and hands off steering wheel.
Back pressure: Lower than 1000 kPa (10 kg / cm
2, 142 psi)
When back pressure is higher than specified values, check con-
trol valve and piping for clogging.

YH4
GRAND
VITARA
1. P / S fluid reservoir
2. Gauge valve (shut)
3. Oil pressure gauge
4. P / S pump
5. P / S gear box
1. P / S fluid reservoir
2. Gauge valve (open)
3. Oil pressure gauge
4. P / S pump
5. P / S gear box
POWER STEERING (P / S) SYSTEM 3B1-11
5) Check relief pressure

Increase engine speed to about 1,500 r / min (rpm). Close
gauge valve gradually while watching pressure increase indi-
cated by gauge and take reading of relief pressure (maximum
hydraulic pressure).
Relief pressure:
6200 ± 7000 kPa
(62 ± 70 kg / cm
2, 882 ± 995 psi) G16 Type engine. . . . . . .
6700 ± 7500 kPa
(67 ± 75 kg / cm
2, 953 ± 1067 psi) J20 Type engine. . . . . . .
7050 ± 7850 kPa
(70.5 ± 78.5 kg / cm
2, 1003 ± 1116 psi) H25 Type engine. .

When it is higher than specified values, possible cause is mal-
function of relief valve.

When it is lower than specified values, possible cause is either
failure of P / S pump or settling of relief valve spring.
CAUTION:
Be sure not to close gauge valve for longer than 10 se-
conds.

Next, open gauge valve fully and increase engine speed to
about 1,500 r / min (rpm). Then turn steering wheel to the left
or right fully and take reading of relief pressure.
Relief pressure:
6200 ± 7000 kPa
(62 ± 70 kg / cm
2, 882 ± 995 psi) G16 Type engine. . . . . . .
6700 ± 7500 kPa
(67 ± 75 kg / cm
2, 953 ± 1067 psi) J20 Type engine. . . . . . .
7050 ± 7850 kPa
(70.5 ± 78.5 kg / cm
2, 1003 ± 1116 psi) H25 Type engine. .

When it is higher than specified values, possible cause is mal-
function of relief valve.

When it is lower than specified values, possible cause is failure
in steering gear box. Replace gear box.
CAUTION:
Be sure not to hold steering wheel at fully turned posi-
tion for longer than 10 seconds.
BOOT
STEERING RACK BOOT CHECK
Check boot for crack and damage which, if any, means possibility
of rusty gear, entry of dust or lack of grease. Also, check if any of
such faulty conditions exists.
Check steering rack boot for dent or breakage.
If there is a dent, keep boot in most compressed state for some se-
conds to correct dent.

YH4
GRAND
VITARA
1. High pressure pipe
2. Union bolt3. Low pressure hose
4. Steering lower shaft bolt
3B1-14 POWER STEERING (P / S) SYSTEM
3) After installing wheels, lower vehicle and tighten wheel nuts to
specified torque.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
4) Check that proper amount of toe-in is obtained by referring to
ªFRONT WHEEL ALIGNMENTº.
5) After confirming proper amount of toe-in, tighten tie-rod end lock
nut to specified torque.
Tightening Torque
(a): 65 N
.m (6.5 kg-m, 47.0 lb-ft)
POWER STEERING GEAR BOX
ASSEMBLY
REMOVAL
1) Take out fluid in P / S fluid reservoir with syringe or such.
2) Disconnect high pressure pipe from steering gear box by remov-
ing union bolt.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to pipe.
3) Disconnect low pressure hose from steering gear box.
NOTE:
As fluid flows out of disconnected joints, put a receptacle
under joints or a plug to hose.
4) Remove steering lower shaft bolt.
5) Hoist vehicle and remove both right and left wheels.
6) Disconnect both right and left tie rod ends from knuckle, refer to
steps 2) to 3) of ªTIE-ROD END REMOVALº in this section.