1999 SUZUKI GRAND VITARA Mount

YH4
GRAND
VITARA
REAR SUSPENSION 3E-15
1. Inner oil seal
2. Axle housing
1. Hammer
2. Screwdriver
3. Oil seal protector
4. Oil seal
5. Body center
REAR AXLE SHAFT INNER OIL SEAL
REMOVAL
1) Remove rear axle shaft. For details, refer to steps 1) to 7) of
REAR AXLE SHAFT REMOVAL in this section.
2) Fix brake back plate by inserting screwdriver to the hole for bear-
ing retainer mounting.
3) Remove rear axle shaft inner oil seal.
NOTE:
Take care not to bend the brake pipe.
INSTALLATION
1) Using special tool drive in oil seal until it contacts oil seal protec-
tor in axle housing.
NOTE:

Make sure that oil seal is free from inclination as it is
installed.

Refer to figure so that oil seal is installed in proper direc-
tion.
Special Tool
(A): 09913-75510
ªAº: Grease 99000-25010
ªBº: Sealant 99000-31110
2) For procedure hereafter, refer to steps 6) to 11) of REAR AXLE
SHAFT INSTALLATION in this section.

YH4
GRAND
VITARA
3E-18 REAR SUSPENSION
1. Axle housing
2. Jack
1. Differential carrier
assembly
2. Differential carrier nut
1. Lower rod
2. Lower rod rear
mount nut
3. Shock absorber
1. Lower mount
bolt
13) For jobs hereafter, support rear axle housing by using floor jack
under axle housing.
14) Remove differential carrier assembly.
15) Loosen rear mount nut of upper rod but don't remove bolt.
16) Loosen rear mount nut of lower rod but don't remove bolt.
17) Remove rear axle side lateral rod mount bolt.
18) Remove shock absorber lower mount bolt.
19) Lower floor jack until tension of suspension coil spring be-
comes a little loose and remove rear mount bolt of upper , lower
and lateral rod.
20) Lower rear axle housing gradually.
21) Remove axle housing.

YH4
GRAND
VITARA
1. Lower rod
2. Body center
1. Rear axle housing
2. Spring seat
3. Coil spring
4. Stepped part
1. Axle housing ªAº 1. Body center
1
2
1
REAR SUSPENSION 3E-19
INSTALLATION
Install removed parts in reverse order of removal, noting the follow-
ing.
1) Place rear axle housing on floor jack. Then install upper / lower
rod rear mounting bolts (right & left) in proper direction as shown
(refer to UPPER ROD INSTALLATION for upper rod bolts). At
this time, mount nuts but don't tighten them.
2) Install coil spring (right & left) on spring seat of axle housing and
raise axle housing.
NOTE:
When seating coil spring, mate spring end with stepped
part of rear axle spring seat as shown.
3) Install lateral rod to rear axle housing.
4) Install lower part of shock absorber to right and left sides of axle
housing and install bolts in proper direction as shown in figure.
At this time, mount nuts but don't tighten them.
5) Clean mating surfaces of axle housing and differential carrier
and apply sealant to housing side.
ªAº: Sealant 99000-31110
6) Install differential carrier assembly to axle housing and tighten
carrier nuts to specified torque.
Tightening Torque
(a): 55 N
.m (5.5 kg-m, 40.0 lb-ft)

YH4
GRAND
VITARA
3E-22 REAR SUSPENSION
23) Install wheel and tighten wheel nuts to specified torque.
Tightening Torque
(h): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
24) Upon completion of all jobs, depress brake pedal with about 30
kg (66 lbs) load three to ten times so as to obtain proper drum-
to-shoe clearance.
Adjust parking brake cable (for adjustment, see SECTION 5C
of this manual.)
25) Tighten parking brake lever cover screws.
26) Lower hoist.
27) Tighten right and left lower / upper rod nuts lateral rod mount
bolt and shock absorber nuts to specified torque.
NOTE:
When tightening these nuts, be sure that vehicle is off
hoist and in non loaded condition.
Tightening Torque
(i): 90 N
.m (9.0 kg-m, 65.0 lb-ft)
(j): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
28) Check to ensure that brake drum is free from dragging and
proper braking is obtained.
29) Perform brake test (foot brake and parking brake).
30) Check each installed part for oil leakage.

YH4
GRAND
VITARA
3F-2 WHEELS AND TIRES
The metric term for tire inflation pressure is the kilopascal (kPa).
Tire pressures will usually be printed in both kPa and psi on the Tire
Placard. Metric tire gauges are available from tool suppliers. The
chart, left table, converts commonly used inflation pressures from
kPa to psi.kPakgf / cm2psi
160
180
200
220
240
260
280
300
320
3401.6
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.423
26
29
32
35
38
41
44
47
50
Conversion:1 psi = 6.895 kPa
1 kgf / cm
2 = 98.066 kPa
WHEELS REPLACEMENT
Wheels must be replaced if they are bent, dented, have excessive
lateral or radial runout, leak air through welds, have elongated bolt
holes, if lug nuts won't stay tight, or if they are heavily rusted.
Wheels with greater runout than shown in left figure may cause ob-
jectional vibrations.
Wheels for replacement must be equivalent to the originally
equipped wheels in load capacity, diameter, rim width, off-set and
mounting configuration. A wheel of improper size or type may affect
wheel and bearing life, brake cooling, speedometer / odometer cal-
ibration, ground clearance to the body and chassis.
To measure the wheel runout, it is necessary to use accurate dial
indicator. The tire may be on or off the wheel. The wheel should be
installed to the wheel balancer of the like for proper measurement.
Take measurements of both lateral runout and radial runout at both
inside and outside of the rim flange. With dial indicator set in place
securely, turn the wheel one full revolution slowly and record every
reading of the indicator.
When the measured runout exceeds the specification and correc-
tion by the balancer adjustment is impossible, replace the wheel.
If the reading is affected by welding, paint or scratch, it should be
ignored.
Lateral runout limit ªaº: 1.20 mm (0.047 in.)
Radial runout limit ªbº: 1.20 mm (0.047 in.)
METRIC LUG NUTS AND WHEEL STUDS
All models use metric lug nuts and wheel studs (size M12 x 1.25).

YH4
GRAND
VITARA
1. Paint
3F-4 WHEELS AND TIRES
Higher than Recommended Pressure Can Cause:
1. Hard ride
2. Tire bruising or carcass damage
3. Rapid tread wear at center of tire
Unequal Pressure on Same Axle Can Cause:
1. Uneven braking
2. Steering lead
3. Reduced handling
4. Swerve on acceleration
Valve caps should be kept on valves to keep dust and
water out.Lower than Recommended Pressure Can Cause:
1. Tire squeal on turns
2. Hard steering
3. Rapid and uneven wear on the edges of the tread
4. Tire rim bruises and rupture
5. Tire cord breakage
6. High tire temperatures
7. Reduced handling
8. High fuel consumption
MAINTENANCE AND MINOR ADJUSTMENTS
WHEEL AND TIRE
Wheel repairs that use welding, heating, or peening are not approved. All damaged wheels should be replaced.
STUDS
If a broken stud is found, see Section 3E (rear) or Section 3D (front) for Note and Replacement procedure.
MATCHED TIRES AND WHEELS
(For vehicle equipped with steel wheels)
Tires and wheels are matchmounted at the assembly plant.
This means that the radially stiffest part of the tire, or ªhigh spotº, is
matched to the smallest radius or ªlow spotº of the wheel.
This is done to provide the smoothest possible ride.
The ªhigh spotº of the tire is originally marked by paint dot on the
outboard sidewall. This paint dot will eventually wash off the tire.
The ªlow spotº of the wheel is originally marked by paint dot on the
wheel rim-flange. Properly assembled, the wheel rims' paint dot
should be aligned with the tires' paint dot as shown in left figure.
Whenever a tire is dismounted from its wheel, it should be re-
mounted so that the tire and wheel are matched. If the tire's paint
dot cannot be located, a line should be scribed on the tire and wheel
before dismounting to assure that it is remounted in the same posi-
tion.
INFLATION OF TIRES
The pressure recommended for any model is carefully calculated to give a satisfactory ride, stability, steering, tread
wear, tire life and resistance to bruises.
Tire pressure, with tires cold, (after vehicle has set for three hours or more, or driven less than one mile) should
be checked monthly or before any extended trip. Set to the specifications on the tire placard located on the side
of instrument panel.
It is normal for tire pressure increase when the tires become hot during driving. Do not bleed or reduce tire pressure
after driving. Bleeding reduces the ªCold Inflation Pressureº.

YH4
GRAND
VITARA
3F-6 WHEELS AND TIRES
ON-VEHICLE SERVICE
WHEEL
REMOVAL
1) Loosen wheel nuts by approximately 180
(half a rotation).
2) Hoist vehicle.
3) Remove wheel.
NOTE:
Never use heat to loosen tight wheel because application of
heat to wheel can shorten life of wheel and damage wheel
bearings.
INSTALLATION
Wheel nuts must be tightened in sequence and to proper torque to
avoid bending wheel or brake drum or disc as in figure.
NOTE:
Before installing wheels, remove any build-up of corrosion on
wheel mounting surface and brake drum or disc mounting sur-
face by scraping and wire brushing. Installing wheels without
good metal-to-metal contact at mounting surfaces can cause
wheel nuts to loosen, which can later allow wheel to come off
while vehicle is moving.
Tightening Torque
(a): 100 N
.m (10.0 kg-m, 72.5 lb-ft)

YH4
GRAND
VITARA
WHEELS AND TIRES 3F-7
TIRE
MOUNTING AND DEMOUNTING
Use tire changing machine to mount or demount tires. Follow equip-
ment manufacturer's instructions. Do not use hand tools or tire
irons alone to change tires as they may damage tire beads or wheel
rim.
Rim bead seats should be cleaned with wire brush or coarse steel
wool to remove lubricants, old rubber and light rust. Before mount-
ing or demounting tire, bead area should be well lubricated with ap-
proved tire lubricant.
After mounting, inflate to 240 kPa (35psi) so that beads are com-
pletely seated. Then adjust pressure to specified shown an tire
placard.
WARNING:
Do not stand over tire when inflating. Bead may break when
bead snaps over rim's safety hump and cause serious per-
sonal injury.
Do not exceed 240 kPa (35 psi) pressure when inflating. If
240 kPa (35 psi) pressure will not seat beads, deflate, re-lu-
bricate and reinflate. Over inflation may cause bead to break
and cause serious personal injury.
Install valve core and inflate to proper pressure.
TIRE REPAIR
There are many different materials and techniques on the market
to repair tires. As not all of these work on all types of tires, tire
manufacturers have published detailed instructions on how and
when to repair tires. These instructions can be obtained from the
tire manufacturer.