1999 SUZUKI GRAND VITARA Stall

YH4
GRAND
VITARA
9-80 BODY SERVICE
1. Bolt
2. Member
LUGGAGE UNDER BOX
WARNING:
Do not remove member in the center of luggage under box.
If member had to be removed temporarily for repair or for some oth-
er reason, be sure to reinstall it by using specified new bolts until
head of bolt is broken off.

YH4
GRAND
VITARA
10A
SEAT BELT 10A-1
SECTION 10A
SEAT BELT
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above proce-
dures are not followed, parts or system damage could result.
CONTENTS
GENERAL DESCRIPTIONRefer to SECTION 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Service precautions10A-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front seat belt10A-3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Rear seat belt10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS10A-6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
10A-2 SEAT BELT
ON-VEHICLE SERVICE
SERVICE PRECAUTIONS
WARNING:
If replacing seat belt is necessary, replace buckle and ELR (or webbing) together as a set. This is for
the reason of ensuring locking of tongue plate with buckle. If these parts are replaced individually, such
a locking condition may become unreliable. For this reason, SUZUKI will supply only the spare buckle
and ELR (or webbing) in a set part.
Before servicing or replacing seat belts, refer to following precautionary items.

Seat belts should be normal relative to strap retractor and buckle portions.

Keep sharp edges and damaging objects away from belts. Avoid bending or damaging any portion of belt buckle,
latch plate and ELR.

Do not bleach or dye belt webbing. (Use only mild soap and lukewarm water to clean it.)

When installing a seat belt anchor bolt, start bolt by hand to prevent cross-threading.

Use only the correct seat belt anchor bolts and screws and tighten to the correct torque value.

Do not attempt any repairs on retractor mechanisms or retractor covers. Replace defective assemblies with new
replacement parts.

Keep belts dry and clean at all times.

If there exist any parts in question, replace such parts.

Replace belts whose webbing is cut or otherwise damaged.

Do not put anything into trim panel opening which seat belt webbing passes through.

YH4
GRAND
VITARA
SEAT BELT 10A-5
(a)
(a)(a)
(a)
(b)
1. Upper anchor
2. Lower anchor
3. Retractor assembly
4. Buckle
INSTALLATION
Install in reverse order of removal, noting the following.

Seat belt anchor bolts should have an unified fine thread (7 / 16-20 UNF). Under no circumstances should any
different sized or metric screw threads be used.

Be sure to tighten seat belt anchor bolts to specified torque.
Tightening torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
(b): 5.5 N
.m (0.55 kg-m, 4.0 lb-ft)

YH4
GRAND
VITARA
10A-6 SEAT BELT
1. Upper anchor
2. Lower anchor
3. Retractor assembly
4. Buckle: If equipped* *
REAR SEAT BELT
WARNING:
Be sure to read ªService Precautionsº before starting to work and observe every precaution during
work.
REMOVAL
Refer to the figure below to remove rear seat belts.
INSPECTION
Check the rear seat belt in the same way as when inspecting front seat belt. (Refer to page 10A-4.)
INSTALLATION
Install the rear seat belt observing the same precautions as when installing front seat belt. (Refer to page 10A-5.)
Tightening Torque
(a): 35 N
.m (3.5 kg-m, 25.5 lb-ft)
TIGHTENING TORQUE SPECIFICATIONS
FasteningpartsTightening torqueFastening artsN.mkg-mlb-ft
Upper and lower anchor bolt353.525.5
Retractor assembly bolt353.525.5
Retractor assembly screw5.50.554.0
Buckle bolt353.525.5

YH4
GRAND
VITARA
10B
AIR BAG SYSTEM 10B-1
GENERAL DESCRIPTION10B- 3 . . . . . . . . . . . . .
System Components and Wiring
Location View and Connectors 10B- 4. . . . . . .
System Wiring Diagram 10B- 5. . . . . . . . . . . . . .
DIAGNOSIS10B- 6 . . . . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic Trouble Codes 10B- 6. . . . . . . . . . . .
Use of Special Tools 10B- 6. . . . . . . . . . . . . . . . .
Intermittent and Poor Connections 10B- 8. . . . .
Air Bag Diagnostic System Check 10B-10. . . . .
Air bag diagnostic system check
flow table 10B-11. . . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code (DTC) check 10B-12.
Diagnostic trouble code (DTC)
clearance 10B-13. . . . . . . . . . . . . . . . . . . . . . .
Diagnostic trouble code table 10B-14. . . . . . . .
Table A - ªAIR BAGº warning lamp
comes ªONº steady 10B-16. . . . . . . . . . . . . . .
Table B - ªAIR BAGº warning lamp
does not come ªONº 10B-18. . . . . . . . . . . . . .
Table C - ªAIR BAGº warning lamp
flashes 10B-20. . . . . . . . . . . . . . . . . . . . . . . . . .
Table D - SDM cannot communicate
through the serial data circuit 10B-22. . . . . . . Code 15 - Passenger air bag initiator
circuit resistance high 10B-24. . . . . . . . . . . . .
Code 16 - Passenger air bag initiator
circuit resistance low 10B-26. . . . . . . . . . . . . .
Code 18 - Passenger air bag initiator
circuit short to ground 10B-28. . . . . . . . . . . . .
Code 19 - Passenger air bag initiator
circuit short to power circuit 10B-30. . . . . . . .
Code 21 - Driver air bag initiator
circuit resistance high 10B-32. . . . . . . . . . . . .
Code 22 - Driver air bag initiator
circuit resistance low 10B-34. . . . . . . . . . . . . .
Code 24 - Driver air bag initiator
circuit short to ground 10B-36. . . . . . . . . . . . .
Code 25 - Driver air bag initiator
circuit short to power circuit 10B-38. . . . . . . .
Code 31 - Power source voltage high 10B-40
Code 32 - Power source voltage low 10B-42.
Code 41 - Driver pretensioner initiator
circuit resistance high 10B-44. . . . . . . . . . . . .
Code 45 - Passenger pretensioner
initiator circuit resistance high 10B-44. . . . . .
Code 42 - Driver pretensioner initiator
circuit resistance low 10B-46. . . . . . . . . . . . . .
SECTION 10B
AIR BAG SYSTEM
WARNING:

Service on or around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Please observe all WARNINGS and ªService Precautionsº under ªOn-Vehicle
Serviceº in this section before performing service on or around the air bag system components or
wiring. Failure to follow WARNINGS could result in unintended activation of the system or could ren-
der the system inoperative. Either of these two conditions may result in severe injury.

The procedures in this section must be followed in the order listed to disable the air bag system tem-
porarily and prevent false diagnostic trouble codes from setting. Failure to follow procedures could
result in possible activation of the air bag system, personal injury or otherwise unneeded air bag sys-
tem repairs.
CAUTION:
When fasteners are removed, always reinstall them at the same location from which they were re-
moved. If a fastener needs to be replaced, use the correct part number fastener for that application. If
the correct part number fastener is not available, a fastener of equal size and strength (or stronger) may
be used. Fasteners that are not reused, and those requiring thread-locking compound, will be called
out. The correct torque value must be used when installing fasteners that require it. If the above condi-
tions are not followed, parts or system damage could result.
CONTENTS

YH4
GRAND
VITARA
1. Yellow connector of passenger air bag (inflator) module
2. Steering support member
3. Air bag harness
AIR BAG SYSTEM 10B-57
3) Connect Yellow connector of passenger air bag (inflator) mod-
ule, and be sure to lock connector with lock lever.
ii) Connect connector.
ii) Lock connector with lock lever.
4) Install glove box.
5) Install ªAIR BAGº fuse to ªAIR BAGº fuse box.
6) Turn ignition switch to ON and verify that ªAIR BAGº warning
lamp flashes 6 times and then turns off.
If it does not operate as described, perform ªAir Bag Diagnostic
System Checkº in this section.
HANDLING AND STORAGE
SDM
WARNING:
Never power up air bag system when SDM is not rigidly at-
tached to the vehicle. Otherwise, personal injury may result.
CAUTION:
After detecting one time of such collision as to meet deploy-
ment conditions, the SDM must not be used.
Refer to ªDiagnosisº when checking the SDM.

Never attempt disassembly of SDM.

When storing SDM, select a place where neither high tempera-
ture nor high humidity is anticipated and oil, water and dust are
kept off.

If SDM was dropped from a height of 90 cm (3 ft) or more or if it
is found to be damaged or deformed, replace it with a new one.

If installation part of SDM was damaged, repair that part com-
pletely before reinstallation.

All SDM and mounting bracket fasteners must be carefully
torqued and the arrow must be pointed toward the front of the ve-
hicle to ensure proper operation of the air bag system.

YH4
GRAND
VITARA
10B-62 AIR BAG SYSTEM
1. Air bag wire harness
2. Ground
3. SDM case ground
AIR BAG WIRE HARNESS AND CONNECTORS
Air bag wire harness can be identified easily as it is covered with a
yellow protection tube. Be very careful when handling it.

When an open in air bag wire harness, damaged wire harness,
connector or terminal is found, replace wire harness, connectors
and terminals as an assembly.

When installing it, be careful so that the air bag wire harness is not
caught or does not interfere with other parts.

Make sure all air bag system grounding points are clean and
grounds are securely fastened for optimum metal-to-metal con-
tact. Poor grounding can cause intermittent problems that are dif-
ficult to diagnose.
DISPOSAL
Do not dispose of the live (undeployed) air bag (inflator) modules
and the live (inactivated) seat belt pretensioners. When disposal is
necessary, be sure to deploy the air bag according to deployment
procedure described under ªAir Bag (Inflator) Modules Disposalº
and to activate the pretensioner according to activation procedure
described under ªSeat Belt Pretensioners Disposalº.
WARNING:
Failure to follow proper air bag (inflator) module and seat
belt pretensioner disposal procedures can result in air bag
deployment and pretensioner activation which could cause
personal injury. Undeployed air bag (inflator) module and
inactivated seat belt pretensioner must not be disposed of
through normal refuse channels.
The undeployed air bag (inflator) module and inactivated
seat belt pretensioner contain substances that can cause
severe illness or personal injury if the sealed container is
damaged during disposal.