1999 SUZUKI GRAND VITARA Section 8f

YH4
GRAND
VITARA
1. Inner end of interlock cable
2. Key release cam
1. Key release cam
2. Cable outer(a)
Type-2
Type-2
AUTOMATIC TRANSMISSION (4 A / T) 7B1-73
TYPE-2
5) With key release cam set as shown at the left figure, connect
inner end of interlock cable to key release cam. (Select lever
side.)
6) Move key release cam so that it is set at such angle as shown
at the left figure and with special tool inserted in hole A , fix key
release cam.
Special Tool
(A): 09925-78210 (6 mm)
7) With key release cam fixed with special tool, install cable outer
to bracket and after making sure that cable outer is pushed in
arrow direction B by leaf spring, tighten mounting nut to speci-
fied torque. Remove special tool.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
8) Turn ignition key to ªACCº position and shift select lever to ªNº
range, and check for the followings.
a. When select lever is shifted at ªPº range with knob button
depressed, ignition key can not be turned from ªACCº to
ªLOCKº position.
b. When knob button is released, ignition key can be turned to
ªLOCKº position.
c. When ignition key is at ªLOCKº position, select lever can not
be shifted from ªPº to any other range.
9) Install console box.
10) Install steering column cover.
11) Adjust steering column or tighten steering column bolts.
12) Install steering column hole cover.
13) If equipped with air bag system, enable air bag system.
Refer to ªEnabling Air bag Systemº in Section 10B.

YH4
GRAND
VITARA
AUTOMATIC TRANSMISSION (4 A / T) 7B1-77
ªAº, (d)
1. Drive plate
2. Torque converter
3. Case right stiffener (if equipped)
4. Automatic transmissionTightening torque
(a): 50 N´m
5.0 kg-m
36.5 lb-ft
(b): 65 N´m
6.5 kg-m
47.0 lb-ft
(c): 85 N´m
8.5 kg-m
61.5 lb-ft
(d): 78 N´m
7.8 kg-m
56.5 lb-ft
1. Automatic transmission
2. Transfer (4WD)
3. Engine rear mounting
4. Engine rear mounting member Tightening torque
(a): 50 N´m (5.0 kg-m, 36.5 lb-ft) ªAº: Sealant 99000-31110
REMOUNTING
WARNING:
When moving transmission assembly with torque convert-
er equipped in it, be sure to keep it horizontal. Tilting it with
its front facing down may allow converter to fall off. Where-
by an injury may result.
For remounting, reverse dismounting procedure. Use specified
torque as given below and left.
Tightening torque
N.mkg-mlb-ft
Exhaust No.1 pipe to manifold
bolts or nuts505.036.5
Muffler to exhaust No.2 pipe
nuts606.043.5
Universal joint flange bolts and
nuts505.036.5

Oil filler tube bolts

Select cable bracket bolts232.317.0

Clamp wiring harness and hoses securely.

Refer to ªSelect Cableº section for adjusting procedure of select
cable.

Refer to ªA / T Throttle Cableº section for tuning of A / T throttle
cable.

Follow fluid level check procedure for refilling automatic transmis-
sion fluid and its level adjusting.

Connect battery, and confirm that engine and transmission func-
tion acceptably.

When remounting drive plate, use specified bolts.

YH4
GRAND
VITARA
7B1-78 AUTOMATIC TRANSMISSION (4 A / T)
ON-VEHICLE
SERVICE MOUNTING
EXTERNAL
UNIT REPAIR
Refer to the same section of UNIT REPAIR MANUAL mentioned in FOREWORD of this manual.
TIGHTENING TORQUE SPECIFICATIONS
Fastening portion
Tightening torque
Fastening portion
N´mkg-mlb-ft
Automatic transmission fluid drain plug232.317.0
Transfer oil filler / level and drain plugs232.317.0
Transmission case plug171.712.5
Manual select lever nut131.39.5
Manual select cable nut70.75.5
Manual selector assembly bolts181.813.5
Transmission to engine bolts and nuts858.561.5
Engine rear mounting bolts
Engine rear mounting member bolts
Transmission case right stiffener bolts
505.036.5
Universal joint flange bolts and nuts505.036.5
Torque converter mounting bolts656.547.0
Adapter case or extension case bolts
(G16 engine)353.525.5
Adapter case or extension case bolts
(J20 / H25 engines)424.230.0
Transmission range switch lock bolt5.50.554.0
Oil pipe union bolts353.522.5
Drive plate bolts787.856.5
Interlock cable clamp screw2.20.221.5
Interlock cable outer mounting nut131.39.5

YH4
GRAND
VITARA
7C1
CLUTCH 7C1-1
GENERAL DESCRIPTION7C1 - 2 . . . . . . . . . . . . .
DIAGNOSIS7C1 - 3 . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE7C1 - 4 . . . . . . . . . . . . . . .
Clutch Pedal Height 7C1 - 4. . . . . . . . . . . . . . . . . .
Clutch Pedal Free Travel 7C1 - 4. . . . . . . . . . . . .
Clutch Fluid Pipe and Hose 7C1 - 4. . . . . . . . . . .
Clutch Master Cylinder 7C1 - 5. . . . . . . . . . . . . . .
Fluid Inspection 7C1 - 6. . . . . . . . . . . . . . . . . . . . .
Disassembly and Assembly
Clutch Master Cylinder 7C1 - 7. . . . . . . . . . . . . . Clutch Operating Cylinder 7C1 - 8. . . . . . . . . . . .
UNIT REPAIR7C1-10 . . . . . . . . . . . . . . . . . . . . . . . .
Clutch Cover, Clutch Disc and
Flywheel 7C1 - 10. . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE
SPECIFICATIONS7C1-14 . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS7C1-14 . . . . .
SPECIAL TOOLS7C1-14 . . . . . . . . . . . . . . . . . . . . .
SECTION 7C1
CLUTCH
CONTENTS

YH4
GRAND
VITARA
1. Pipe
2. Hose
3. Flare nut
1. Pipe
2. Hose
3. Flare nut
4. E-ring
1. Master cylinder
assembly
2. Clutch pipe
3. Attaching nut
4. Attaching bolt
5. Clevis pin
6. Clip
7. Flare nut
CLUTCH 7C1-5
INSPECTION
Check pipe and hose for dent, kink, crack, dirt and dust. Replace
if check result is not satisfactory.
INSTALLATION
Reverse removal sequence noting following points.
Tighten flare nuts to specified torque.
Tightening Torque
(a): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
NOTE:

For air bleeding of master cylinder alone, it must be removed
from vehicle.
(For procedures of removal and installation of master cylin-
der assembly and air bleeding, refer to CLUTCH MASTER
CYLINDER section.)

Do not allow fluid to get on painted surface.

Do not allow pipe and hose to contact hard against vehicle
or other parts.

Install each clamp securely.

Install E-ring securely as shown.

After installation, check clutch pedal free travel and bleed air
from system.

Check fluid leakage.

Add fluid close to MAX level of reservoir.
CLUTCH MASTER CYLINDER
REMOVAL
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Remove push rod clevis pin.
3) Disconnect fluid pipe from master cylinder.
NOTE:
Do not allow fluid to get on painted surfaces.
4) Remove master cylinder attaching nut and bolt.
5) Remove master cylinder assembly and gasket.

YH4
GRAND
VITARA
1. Master cylinder
1. Attaching bolt
2. Attaching nut
3. Clevis pin
ªAº
7C1-6 CLUTCH
INSTALLATION
1) To bleed air from master cylinder itself, tilt it as shown in figure
and add fluid into it.
NOTE:
After bleeding air from master cylinder, plug pipe hole in it
to prevent fluid from spilling out of it till pipe is connected.
2) Install master cylinder assembly and new gasket to body, attach-
ing bolt, nuts and push rod clevis pin.
NOTE:
Do not reuse gasket.
3) Torque attaching bolt and nut to specification.
4) Connect fluid pipe and torque flare nut to specification.
Tightening Torque
(a): 13 N
.m (1.3 kg-m, 9.5 lb-ft)
(b): 16 N
.m (1.6 kg-m, 11.5 lb-ft)
5) Apply grease to clevis pin and install it.
ªAº: Grease 99000-25010
6) Fill reservoir with specified brake fluid and check fluid leakage.
7) After installation, bleed air from system and check clutch pedal
free travel. Refer to BRAKE section for air bleeding procedure.
FLUID INSPECTION
Fluid level should be always between MIN and MAX lines on reser-
voir. If fluid decreases quickly, check for leakage, repair leaky point,
if any, and add fluid up to MAX level.
NOTE:

Brake fluid damages painted surface badly. Should it get on
painted surface, remove it immediately and clean surface
thoroughly.

Do not use shock absorber fluid or any other fluid which con-
tains mineral oil. Do not use container which has been used
for mineral oil or which is wet from water. Mineral oil will
cause swelling and distortion of rubber parts in hydraulic
clutch system and water will mix with brake fluid, lowering
fluid boiling point. Keep all fluid containers capped to pre-
vent contamination.

Make sure not to use fluid whose container cap was first
opened more than a year ago.

YH4
GRAND
VITARA
ªAº
1. Reservoir cap
2. Cylinder
3. Piston assembly
4. Push rod
5. Piston stopper
6. Circlip
7. Boot
8. Lock nut
9. Clevis
1. Clutch operating cylinder
2. Hose
3. E-ring
7C1-8 CLUTCH
4) Tighten lock nut to specified torque.
Tightening Torque
(a): 10 N
.m (1.0 kg-m, 7.5 lb-ft)
5) For installation of master cylinder to vehicle, refer to INSTALLA-
TION described previously.
CLUTCH OPERATING CYLINDER
REMOVAL
NOTE:
Do not allow fluid to get on painted surfaces.
1) Clean around reservoir cap and take out fluid with syringe or
such.
2) Disconnect fluid hose from operating cylinder.
3) Remove operating cylinder attaching bolts and operating cylin-
der.
INSTALLATION
1) For air bleeding of master cylinder alone, it must be removed
from vehicle.
For procedures of removal and installation of master cylinder as-
sembly and air bleeding, refer to CLUTCH MASTER CYLINDER
section.
2) Apply small amount of grease to rod tip.
ªAº: Grease 99000-25010
NOTE:
Don't allow any grease to be on boot.
3) Install clutch operating cylinder and torque attaching bolts to
specification.
4) Connect clutch fluid hose and torque union bolt to specification.
Tightening Torque
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft)
(b): 23 N
.m (2.3 kg-m, 16.5 lb-ft)

YH4
GRAND
VITARA
CLUTCH 7C1-9
5) Fill reservoir with specified brake fluid and check for fluid leak-
age.
6) Bleed air from system and check clutch pedal free travel. Refer
to BRAKE section for air bleeding procedure.