1999 SUZUKI GRAND VITARA Section 8f

YH4
GRAND
VITARA
1. Clips
2. Pads
3. Disc
4. Caliper carrier
5. Sensor
6. Shim
1. Caliper pin bolts
ELECTRIC brake
caliper
FRONT BRAKE 5B-5
INSTALLATION
NOTE:
See NOTE at the beginning of this section.
1) Install pad clips and pads.
NOTE:
Install pad with sensor to body center side of caliper.
2) Install caliper and torque caliper pin bolts to specification.
Tightening Torque
(a), (b): 27 N
.m (2.7 kg-m, 20.0 lb-ft) For TOKICO brake. .
caliper
(a): 50 N
.m (5.0 kg-m, 36.5 lb-ft) For SUMITOMO. . . . . .
(b): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
NOTE:
Make sure that boots are fit into groove securely.
3) Torque front wheel nuts to specification.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
4) Upon completion of installation, perform brake test.

YH4
GRAND
VITARA
1. 8 mm bolt
5B-10 FRONT BRAKE
FRONT BRAKE DISC
REMOVAL
1) Hoist vehicle and remove wheel.
2) Remove caliper assembly by loosening carrier bolts (2 pcs.).
CAUTION:
During removal, be careful not to damage brake flexible
hose and not to depress brake pedal.
3) Remove disc by using 8 mm bolts (2 pcs.).
INSPECTION
Refer to FRONT DISC BRAKE PAD INSPECTION.
INSTALLATION
NOTE:
See NOTE at the beginning of this section.
1) Install disc to wheel hub.
2) Install caliper assembly to steering knuckle.
3) Torque caliper carrier bolts to specification.
Tightening Torque
(a): 85 N
.m (8.5 kg-m, 61.5 lb-ft)
4) Torque front wheel nuts to specifications.
Tightening Torque
(b): 100 N
.m (10.0 kg-m, 72.5 lb-ft)
5) Upon completion of installation, perform brake test.

YH4
GRAND
VITARA
5C
PARKING AND REAR BRAKE 5C-1
SECTION 5C
PARKING AND REAR BRAKE
WARNING:
For vehicles equipped with Supplemental Restraint (Air Bag) System

Service on and around the air bag system components or wiring must be performed only by an autho-
rized SUZUKI dealer. Refer to ªAir Bag System Components and Wiring Location Viewº under ªGener-
al Descriptionº in air bag system section in order to confirm whether you are performing service on
or near the air bag system components or wiring. Please observe all WARNINGS and ªService Precau-
tionsº under ªOn-Vehicle Serviceº in air bag system section before performing service on or around
the air bag system components or wiring. Failure to follow WARNINGS could result in unintentional
activation of the system or could render the system inoperative. Either of these two conditions may
result in severe injury.

Technical service work must be started at least 90 seconds after the ignition switch is turned to the
ªLOCKº position and the negative cable is disconnected from the battery. Otherwise, the system may
be activated by reserve energy in the Sensing and Diagnostic Module (SDM).
NOTE:
All brake fasteners are important attaching parts in that they could affect the performance of vital parts
and systems, and / or could result in major repair expense. They must be replaced with one of same part
number or with an equivalent part if replacement becomes necessary. Do not use a replacement part of
lesser quality or substitute design. Torque values must be used as specified during reassembly to assure
proper retention of all parts. There is to be no welding as it may result in extensive damage and weakening
of the metal.
CONTENTS
GENERAL DESCRIPTION5C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Drum Brake Assembly5C- 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
DIAGNOSIS5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CHECK AND ADJUSTMENT5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ON-VEHICLE SERVICE5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Lever5C- 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Parking Brake Cable5C- 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Drum5C- 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Shoe5C- 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wheel Cylinder5C-12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Brake Back Plate5C-14 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TIGHTENING TORQUE SPECIFICATIONS5C-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
REQUIRED SERVICE MATERIALS5C-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPECIAL TOOLS5C-17 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

YH4
GRAND
VITARA
2. Brake cable
3. Locking nut
1. Parking brake cable
2. Equalizer
3. Pin
4. Parking brake lever bolt
5. Parking brake lever assembly1. Parking
brake lever
PARKING AND REAR BRAKE 5C-3
DIAGNOSIS
Refer to Section 5 (BRAKES).
CHECK AND ADJUSTMENT
Refer to Section 5 (BRAKES).
ON-VEHICLE SERVICE
PARKING BRAKE LEVER
REMOVAL
1) Disconnect negative (±) cable at battery.
2) Block vehicle wheels and release parking brake lever.
3) Remove rear center console box.
4) Disconnect lead wire of parking brake switch at coupler.
5) Remove parking brake cable locking nut.
6) Remove parking brake lever bolts and then remove parking
brake lever assembly from equalizer.
7) Remove equalizer from parking brake cable.
NOTE:
Don't disassemble parking brake lever switch. It must be re-
moved and installed as a complete switch assembly.

YH4
GRAND
VITARA
1. Parking brake cable
2. Equalizer
3. Pin
4. Parking brake lever bolt
5. Parking brake lever assembly
5C-4 PARKING AND REAR BRAKE
INSTALLATION
1) Install in reverse order of REMOVAL procedure.
Check equalizer inclined angle.
Angle ªaº: within 15 degrees
Tightening Torque
(a): 23 N
.m (2.3 kg-m, 17.0 lb-ft)
2) After all parts are installed, parking brake lever needs to be ad-
justed. Refer to PARKING BRAKE INSPECTION AND AD-
JUSTMENT in Section 5.
3) Check brake drum for dragging and brake system for proper per-
formance.

YH4
GRAND
VITARA
A-1. Color ring
A-2. Cable
A-3. Grommet
A-4. Bolt
A-5. Clamp (if equipped)A-6. Cross-member
A-7. Chassis frame
A-8. Hanger
A-9. Rear axle
A-10. G-sensor (if equipped) B-1. Parking brake switch
B-2. Parking brake lever
B-3. Parking brake lever bolt
B-4. Floor
B-5. Locking nut
B-6. Spacer
B-7. Pin
B-8. Equalizer
B-9. Adjust rod
B-10. Coupler
PARKING AND REAR BRAKE 5C-5
PARKING BRAKE CABLE
REMOVAL
1) Remove brake drum. (Refer to steps 1) to 5) of BRAKE DRUM
REMOVAL of this section.)
2) Check the color of ring or tape for reinstallation.
NOTE:
Color ring on brake cable is for the purpose of identifica-
tion.
3) Disconnect parking brake cable from brake shoe lever. (Refer to
steps 2) to 5) of BRAKE SHOE REMOVAL of this section.)
4) Disconnect brake cable from brake back plate. (Refer to step 4)
of BRAKE BACK PLATE REMOVAL.)
NOTE:
When it is necessary to remove both right and left parking
brake cables, repeat above steps 1) to 3) on right and left
wheels.
5) Remove cable from parking brake lever. (Refer to steps 1) to 5)
of PARKING BRAKE LEVER REMOVAL of this section.)

YH4
GRAND
VITARA
1. Brake back plate
2. Cable cap
3. Brake cable
1. Parking brake shoe lever
2. Spring
3. Nipple end
5C-6 PARKING AND REAR BRAKE
INSTALLATION
Install parts in reverse order of removal procedure, noting the fol-
lowing.
1) Install brake cable cap to brake back plate securely as shown in
figure.
NOTE:
Color ring or tape on brake cable is for the purpose of identi-
fication. Use cable with the same colored ring as before re-
moval.
2) Install brake cable spring and nipple end to parking brake shoe
lever securely as shown in figure.
3) For brake shoe installation, refer to steps 1) and 4) of BRAKE
SHOE INSTALLATION of this section.
4) For brake drum installation, refer to steps 1) and 3) of BRAKE
DRUM INSTALLATION of this section.
5) For proper routing and secure clamping of parking brake cable.
6) For installation of cable to parking brake lever, refer to PARKING
BRAKE LEVER INSTALLATION of this section.
7) Upon completion of installation, adjust cable. (Refer to PARK-
ING BRAKE CHECK AND ADJUSTMENT in Section 5.) Then
check brake drum for dragging and brake system for proper per-
formance. After removing vehicle from hoist, brake test should
be performed.

YH4
GRAND
VITARA
1. Pawl lever
2. Adjuster
3. Brake shoes
5C-8 PARKING AND REAR BRAKE
Cracked, Scored, or Grooved Drum
A cracked, drum is unsafe for further service and must be replaced.
Do not attempt to weld a cracked drum.
Smooth up any slight scores. Heavy or extensive scoring will cause
excessive brake lining wear and it will probably be necessary to re-
surface drum braking surface.
If brake linings are slightly worn and drum is grooved, drum should
be polished with fine emery cloth but should no be turned.
NOTE:
When drum is removed, visually inspect wheel cylinder for
brake fluid leakage. Correct leaky point, if any.
Brake Shoe
Where lining is worn out beyond service limit, replace shoe.
Thickness ªaº
Standard: 6.5 mm (0.24 in.)
Service limit: 3.0 mm (0.12 in.)
If one of brake linings is to service limit, all linings must be replaced
at the same time.
CAUTION:
Never polish lining with sandpaper. If lining is polished with
sandpaper, hard particles of sandpaper will be deposited in
lining and may damage drum. When it is required to correct
lining, replace it with a new one.
INSTALLATION
NOTE:
See NOTE at the beginning of the section.
1) Before installing brake drum, check outer diameter of brake
shoes. If it is not within value as specified below, adjust it to spec-
ification by turning adjuster.
Outer diameter of brake shoes
ªaº: 219.4 ± 219.7 mm (8.638 ± 8.650 in.)