1999 SUZUKI GRAND VITARA oil type

IGNITION SYSTEM (FOR H27 ENGINE) 6F2-9
INSPECTION
Inspect them for electrode wear, carbon deposits and Insulator
damage.
If any abnormality is found, replace them with specified new plug.
Spark plug air gap “a” :
1.0 – 1.1 mm (0.039 – 0.043 in.)
Spark plug type :
DENSO K20PR-U11/SK16PR11
NGK BKR6E-11/*IFR5J11
INSTALLATION
1) Install spark plug (3) and tighten them to specified torque.
Tightening torque
Spark plug (a) : 25 N·m (2.5 kg-m, 18.0 lb-ft)
2) Install ignition coil assembly (2) securely.
3) Tighten ignition coil bolt (1), and then connect ignition coil
coupler.
4) Install ignition coil cover.CAUTION:
When servicing the iridium/platinum spark plugs (slender
center electrode type plugs), do not touch the center
electrode to avoid damage to it. The electrode is not
strong enough against mechanical force as it is slender
and its material is not mechanically tough.
NOTE:
Under –25°C (–13°F), it is highly recommended to use the
spark plugs with an asterisk (*) for better engine starting
performance.

AUTOMATIC TRANSMISSION (4 A/T) 7B1-3
General Description
Item Specifications
Torque
converterType 3-element, 1-step, 2-phase type (with TCC (lock-up) mechanism)
Stall torque ratio 2.0
Oil pump Type Trochoid type oil pump
Drive system Engine driven
Gear
change
deviceType Forward 4-step, reverse 1-step planetary gear type
Shift position“P” range Gear in neutral, output shaft fixed, engine start
“R” range Reverse
“N” range Gear in neutral, engine start
“D” range
(O/D ON)Forward 1st ↔ 2nd ↔ 3rd ↔ 4th (O/D)
automatic gear change
“D” range
(O/D OFF)Forward 1st ↔ 2nd ↔ 3rd
automatic gear change
“2” range (Normal mode) Forward 1st ↔ 2nd ← 3rd auto-
matic gear change
(Power mode) Forward 2nd ← 3rd automatic gear
change and fixed at 2nd gear
“L” range Forward 1st ← 2nd ← 3rd reduction, and fixed at
1st gear
Gear
ratio1st
(low gear)2.826
2nd
(second gear)1.493
3rd
(top gear)1.000
4th
(overdrive gear)0.689
Reverse
(reverse gear2.703
Control elements Wet type multi-disc clutch ... 3 sets
Wet type multi-disc brake ... 4 sets
One-way clutch ... 3 sets
Transfer Hi : 1.000
Lo : 1.816 (4WD model only)
Final gear reduction
ratio (Differential)5.125
Lubrication Lubrication system Force feed system by oil pump
Cooling Cooling system Radiator assisted cooling (water-cooled)
Fluid used
An equivalent of DEXRON
III

7F-2 DIFFERENTIAL (REAR)
General Description
The differential assembly using a hypoid bevel pinion and gear is installed to the rear axle. It is set in the conven-
tional type axle housing.
The differential assembly is decisive in that the drive power is concentrated there. Therefore, use of genuine
parts and specified torque is compulsory. Further, because of sliding tooth meshing with high pressure between
bevel pinion and gear, it is mandatory to lubricate them by hypoid gear oil.
Diagnosis
Diagnosis Table
Condition Possible Cause Correction
Gear noiseDeteriorated or water mixed lubricant Repair and replenish.
Inadequate or insufficient lubricant Repair and replenish.
Maladjusted backlash between drive bevel pin-
ion and gearAdjust as prescribed.
Improper tooth contact in the mesh between
drive bevel pinion and gearAdjust or replace.
Loose drive bevel gear securing bolts Replace or retighten.
Damaged differential gear(s) or differential pin-
ion(s)Replace.
Bearing noise(Constant noise) Deteriorated or water mixed
lubricantRepair and replenish.
(Constant noise) Inadequate or insufficient
lubricantRepair and replenish.
(Noise while coasting) Damaged bearing(s) of
drive bevel pinionReplace.
(Noise while turning) Damaged differential side
bearing(s) or axle bearing(s)Replace.
Oil leakageClogged breather plug Clean.
Worn or damaged oil seal Replace.
Excessive oil Adjust oil level.