1999 SUZUKI BALENO Fan belt

60G-74E
BEFORE DRIVING

DRIVER SEAT HEIGHT ADJUSTER

(if equipped)
ADJUSTABLE HEAD RESTRAINTS

(if equipped)

606-03-015

If the driver's seat is equipped with a seat

height adjuster knob on the outboard side of

the seat, adjust the seat to the proper height

by turning the adjuster knob.

WARNING
72F-03-014

Adjusting Seatbacks

The seatbacks can be adjusted to different

angles. To adjust the seatback angle, pull up

the lever on the outboard side of the seat,

move the seatback to the desired position, and

release the lever to lock the seatback in place.

Seatbacks should always be in an

upright position when driving, or seat

belt effectiveness may be reduced. Seat

belts are designed to offer maximum

protection when seatbacks are in the

fully upright position.
70F-01-019

WARNING

Head restraints are designed to help reduce

the risk of neck injuries in the case of an

accident. Adjust the head restraint to the

position which places the top of the head

restraint closest to the top or your ears.

23

3-10

BEFORE DRIVING

60G-74E

SEAT BELTS

60G-03-016

To raise the head restraint, pull upward ort the

restraint until it clicks. To lower the restraint,

push down on the restraint while holding in

the lock lever. If a head restraint must be

removed (for cleaning, replacement, etc.),

push in the lock lever and pull the head

restraint all the way out.
70F-01-022E

Wear your Seat Belts at All Times.

WARNING

Never allow persons to ride in the

cargo area of a vehicle. In the event

of an accident, there is a much

greater risk of injury for persons who

are not riding In a seat with their seat

belt securely fastened.

Seat belts should always be adjusted

so the lap portion of the belt is worn

low across the pelvis, not across the

waist. Shoulder straps should be
WARNING

1 worn on the outside shoulder only,

and never under the arm. Seat belts

should never be worn with the straps

twisted and should be adjusted as

tightly as is comfortable to provide

the protection for which they have

been designed. A slack belt will

provide less protection than one

which is snug.

Make sure that each seat belt buckle

is inserted into the proper buckle

catch. It is possible to cross the

buckles in the rear seat.

Do not wear your seat belt over hard

or breakable objects in your pockets

or on your clothing. If an accident

occurs, objects such as glasses,

pens, etc. under the seat belt can

cause injury.

Never use the same seat belt on

more than one occupant and never

attach a seat belt over an infant or

child being held on an occupant's

lap. Such seat belt use could cause

serious injury in the event of an

accident. _K

3-11
24

60G-74E

BEFORE DRIVING

Pregnant women should use seat

belts, although specific recommen-

dations about restraint use should

be made by the woman's medical

advisor.

Periodically inspect seat belt

assemblies for excessive wear and

damage. Seat belts should be replaced

if webbing becomes frayed,

contaminated, or damaged in any way.

It is essential to replace the entire seat

belt assembly after it has been

stressed in an impact, even if damage

to the assembly is not obvious.

Infants and small children should never

be transported unless they are properly

restrained. Restraint systems for

infants and small children can be

purchased locally and should be used.

Make sure that the system you

purchase meets applicable safety

standards. Read and follow all the

directions provided by the

manufacturer.
Avoid contamination of seat belt

webbing by polishes, oils, chemicals,

and particularly battery acid. Cleaning

may safely be carried out using mild

soap and water.

For children, if the shoulder belt

irritates the neck or face, move the child

closer to the center of the vehicle.

A WARNING

Be sure to inspect all seat belt

assemblies after any collision. Any seat

belt assembly which was in use during

a collision (other than a very minor one)

should be replaced, even if damage to

the assembly is not obvious. Any seat

belt assembly which was not in use

during a collision should be replaced

if it does not function properly or is

damaged in any way.
70F-01-021

There are two types of seat belt, "Lap-shoulder

belt" and "Lap belt".

To fasten the seat belt, sit up straight and well

back in the seat, pull the buckle tongue

attached to the seat belt across your body and

slide it into the buckle catch on the opposite

side until you hear a "click".

25

3-12

BEFORE DRIVING
60G-74E

70F-01-022E

To reduce the risk of sliding under the belt

during a collision, position the lap portion of

the belt across your lap as low on your hips

as possible and adjust the belt to a snug fit

using the proper method for each type of the

belt as described below. Make sure that the

belt is not twisted.
70F-01-023E

To unfasten the belt, press the release button

on the buckle catch.
70F-01-024E

To Adjust the Belt

• Lap-shoulder belt

Pull the shoulder portion of the belt

upwards through the tongue plate.

The length of the diagonal shoulder strap

adjusts itself to allow freedom of movement.

The seat belt has an emergency locking

retractor (ELR), which is designed to lock the

seat belt only during a sudden stop or impact.

3-13
26

60Q-74E
BEFORE DRIVING

70F-01-025

Your vehicle is equipped with the shoulder

anchor height adjusters for the front seat belts,

adjust the shoulder anchor height so that the

shoulder belt rides on the center of the

outboard shoulder. To adjust the shoulder

anchor height, slide the anchor up or down

while pulling the lock knob out. After

adjustment, make sure that the acnhor is

securely locked.

No modifications or additions of any

sort should be made to the seat belt or

its operating mechanism.
60G-03-017

Seat Belt Hanger (if equipped)

When you move a seatback, make sure

the belt webbing is hooked in the belt

hangers so the seat belts are not

caught by the seatback, seat hinge, or

seat latch. This helps prevent damage

to the belt system.
60G-03-018E

Lap belt

On this belt the adjuster is incorporated in

the tongue unit.

To tighten the belt, pull the free end of the

belt across alongside the lap strap until it

is adjusted to a snug comfortable position.

27

3-14

BEFORE DRIVING

60G-74E

60G-03-019E

To lengthen, release the tongue from the

buckle unit, pull the tongue (adjuster) in the

direction of the arrow, at right angles to the

belt. The tongue should then be refitted into

the buckle unit and the belt tightened as

previously described.
60G-03-020E

NOTE:

To identify the center seat belt buckle catch

and tongue in the rear seat, "CENTER" is

moulded on the buckle catch and tongue of

the center lap belt. The buckle catches are

designed so a buckle tongue can not be

inserted into the wrong buckle catch.
70F-01-030

Child Restraint Systems

MARUTI highly recommends that you use a

child restraint system to restrain infants and

small children. Many different types of child

restraint systems are available; make sure that

the restaint system you select meets

applicable safety standards.

All child restraint systems are designed to be

secured in vehicle seats by lap belts or the

lap portion of lap-shoulder belts. Whenever

possible, Maruti recommends that child

restraint systems be installed on the rear seat.

According to accident statistics children are

safer when properly restrained in rear seating

positions than in front seating positions.

3-15
28

S0G-74E
OPERATING YOUR VEHICLE

OPERATING YOUR VEHICLE

Exhaust Gas Warning 7-1

Daily Inspection Checklist 7-1

Starting the Engine 7-2

Using the Transmission 7-3

Braking 7-4

Running-in 7-5

Catalytic Converter (if equipped) 7-6

Improving Fuel Economy 7-7

Trailer Towing 7-7

OPERATING YOUR VECHILE

60G-74E

EXHAUST GAS WARNING
DAILY INSPECTION CHECKLIST

60G-07-001E

Avoid breathing exhaust gases.

Exhaust gases contain carbon

monoxide, a potentially lethal gas that

is colourless and odourless. Since

carbon monoxide is difficult to detect

by itself, be sure to take the following

precautions to help prevent carbon

monoxide from entering your vehicle.

• Do not leave the engine running in

garages or other confined areas.

• Do not park with the engine running

for a long period of time, even in an

open area. If it is necessary to sit for

a short time in a parked vehicle <=>
with the engine running, make sure

the air intake lever is set to "FRESH

AIR" and the fan is at high speed.

To allow proper operation of your

vehicle's ventilation system, keep

the air inlet grille in front of the

windscreen clear of snow, leaves, or

other obstructions at all times.

Keep the exhaust tailpipe area clear

of snow and other material to help

reduce the buildup of exhaust gases

under the vehicle.This is particularly

important when parked in blizzard

conditions.

Have the exhaust system inspected

periodically for damage and leaks.

Any damage or leaks should be

repaired immediately.

7-1
70F-05-007

Before driving:

1) Make sure that windows, mirrors, lights,

and reflectors are clean and unobstructed.

2) Check the tyres.

3) Look for fluid and oil leaks.

NOTE:

It is normal for water to drip from the air

conditioning system after use.

4) Adjust the seat/head restraint.

5) Check the brake pedal and the parking

brake lever.

6) Adjust the mirrors.

7) Make sure that you and passengers have

properly fastened your seat belts.

8) Make sure that all warning lights come on

as the key is turned to the "ON" or "START'

position.

9) Check all gauges.

10) Make sure that the brake fluid level

warning light is off when the parking brake

is released with the ignition switch in "ON"

position.

66
65

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

EMERGENCY SERVICE

60G-74E

JACKING INSTRUCTIONS

60G-06-009

1) Park the vehicle securely on hard level

ground.

2) Apply the parking brake firmly and shift into

"R" (Reverse). Choke the front and rear wheel

diagonally opposite the wheel to be changed.

3) Switch on the hazard warning flasher if your

vehicle is in or near traffic.

4) Slacken but do not remove wheel nuts on the

wheel to be changed.

5) Position the jack vertically and raise the jack

by turning the jack handle clockwise until the

jack head recess fits the frame boss.

6) Continue to raise the jack slowly and smoothly

until the tyre clears the ground. Do not raise

the vehicle more than necessary.

10-1
63B-10-001E

70F-08-001

60G-10-001

NOTE:

Use the wheel nut wrench in combination with

jack crank to raise or lower the jack as shown

in the illustration.
Use the jack only to change wheels.

Never jack up the vehicle on an

inclined surface.

Never raise the vehicle with the jack in

a location other than under the frame

boss near the wheel to be changed.

Make sure that the jack is raised at

least 2 inches (51 mm) before it

contacts the vehicle. Use of the jack

when it is within 2 inches of being

fully collapsed may result in failure

of the jack.

Never get under the vehicle when it

is supported by the jack. t=>

116

60G-74E
EMERGENCY SERVICE

JUMP STARTING INSTRUCTIONS

60G-10-002
60G-10-003

Never run the engine when the

vehicle is supported by the jack and

never allow passengers to remain in

the vehicle.
Never attempt to jump start your

vehicle if the battery appears to be

frozen. Batteries in this condition

may explode or rupture if jump

starting is attempted.

When making jump lead

connections, be certain that your

hands and the Jump leads remain

clear from pulleys, belts, or fans.

Batteries produce flammable

hydrogen gas. Keep flames and

sparks away from the battery or an

explosion may occur. Never smoke

when working in the vicinity of the

battery.

If the booster battery you use for

jump starting is installed in another

vehicle, make sure the two vehicles

are not touching each other.

If your battery discharges

repeatedly, for no apparent reason,

have your vehicle inspected by an

authorized MARUTI dealer.

To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions below

precisely and in order. If you are in

doubt, call for qualified road service.

10-2

EMERGENCY SERVICE

60G-74E

WARNING TRIANGLE (TYPE-1)

If the temperature indication does not come

down to within the normal, acceptable range:

1) Turn off the engine and check that the

water pump belt and pulleys are not

damaged or slipping. If any abnormality is

found, correct it.

2) Check the coolant level in the reservoir. If

it is found to be lower than the "LOW" line,

look for leaks at the radiator, water pump,

and radiator and heater hoses. If you

locate any leaks that may have caused the

overheating, do not run the engine until

these problems have been corrected.

3) If you do not find a leak, carefully add

coolant to the reservoir and then the

radiator, if necessary. (Refer to "ENGINE

COOLANr in the "INSPECTION AND

MAINTENANCE" section.)
K is dangerous to remove the radiator

cap when the water temperature is

high, because scalding fluid and steam

may be blown out under pressure. The

cap should only be taken off when the

coolant temperature has lowered.

To help prevent personal Injury, keep

hands, tools and clothing away from the

engine cooling fan and airconditioner

fan (if equipped). These electric fans

can automatically turn on without

warning.
843-10-004

In case of vehicle break-down or during

emergency stopping where your vehicle could

become a potential traffic hazard, please keep

the warning triangle, provided with your

vehicle, on the pathway (road) behind the

vehicle so as to warn the approaching traffic,

at an approximate distance of 5-15 m, such

that reflecting side of the triangle faces the

rear. Please activate the hazard warning lamps

before alighting the vehicle to keep the warning

triangle.

10-5
120

60G-74E
EMERGENCY SERVICE

WARNING TRIANGLE (TYPE-2)

In case of vehicle breakdown or during

emergency stopping where your vehicle

could become a potential traffic hazard,

keep the warning triangle, provided with

your vehicle, on the road free from any

obstacles behind your vehicle so as to warn

the approaching traffic, at an approximate

distance of 50-100 m, the reflecting side of

the triangle should face the on coming

traffic. Please activate the hazard warning

lamps before alighting the vehicle to keep

the warning triangle.
Remove the warning triangle

carefully from the box as shown by arrow

1.

Open both the reflector arms as shown

by arrows and lock arms with each other

with the clip provided in the right arm.

Open the bottom stand in counter clock-

wise direction as shown by arrow 3.

Position the warning triangle behind the

vehicle on a plain surface.

Reverse the removal procedure

keeping inside the box.
for

121

10-6