1999 SUZUKI BALENO service

60G-74E
INSPECTION AND MAINTENANCE

INSPECTION AND MAINTENANCE

Periodic Maintenance Schedule.. 9-2

Engine Oil and Filter 9-7

Gear OH 9-10

Engine Coolant 9-11

Windscreen Washer Fluid 9-13

Air Cleaner 9-13

Spark Plugs 9-14

Brakes 9-15

Steering 9-17

Power Steering (if equipped) 9-18

Clutch Pedal 9-18

Tyres... 9-19

Battery 9-22

Fuses 9-23

Bulb Replacement , 9-25

Wiper Blades 9-29

83

INSPECTION AND MAINTENANCE

60G-74E

70F-05-002

You should take extreme care when

working on your vehicle to prevent

accidental injury. Here are a few

precautions that you should be

especially careful to observe:

• Do not leave the engine running in

garages or other confined areas.

• When the engine Is running, keep

hands, clothing, tools, and other

objects away from the fan and water

pump belt. Even though the fan may

not be moving, it can automatically

turn on without warning. ^
When it is necessary to do service

work with the engine running, make

sure that the parking brake is applied

fully and the transmission is in

Neutral.

Do not touch ignition wires or other

ignition system parts when starting

the engine or when the engine is

running, or you could receive an

electric shock.

Be careful not to touch a hot engine,

exhaust manifold and pipes, muffler,

radiator and water hoses.

Do not allow smoking, sparks, or

flames around gasoline or the

battery. Flammable fumes are

present.

Do not get under your vehicle if it is

supported only with the portable

jack provided in your vehicle.

Be careful not to cause accidental

short circuits between the positive

and negative battery terminals.

Keep used oil, coolant, and other

fluids away from children and pets.

Dispose of used fluids properly;

never pour them on the ground, into

sewers, etc.

9-1
84

60G-74E
INSPECTION AND MAINTENANCE

PERIODIC MAINTENANCE SCHEDULE

The following table shows when regular

maintenance on your vehicle is required. This

table shows in kilometres and months when

inspections, adjustments, lubrication and other

services should be performed.

Maruti recommends that maintenance

on your Maruti vehicle be performed by

Maruti Authorised Dealer/Service

Station.
CAUTION

Whenever it becomes necessary to

replace parts on your vehicle, it is

recommended that you use MARUTI

GENUINE PARTS (MGP).

85

9-2

INSPECTION AND MAINTENANCE

6OG-74E

PERIODIC MAINTENANCE SCHEDULE

A....Ad]ust. l....lnspect and correct or replace If necessary.

T....Tighten to specified torque. C....CIean.

R....Replace or change. O....Rotate

L....Lubrlcate.

Note:

This table includes services as scheduled up to 80,000 km mileage. Beyond 80,000 km, carry out the same services at the same intervals

respectively.

Interval: This interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ENGINE

1. Water pump drive belt (tension, wear)

2. Engine coolant (level, leakage)

3. Engine oil (API GRADE SF, SG, SH) & Oil filter

4. Cooling system hoses and connections (leakage, damage)

5. Engine bolts (All cylinder head and manifold fixings)

6. Engine mounting (loose, damage)

7. Valve clearance

8. Camshaft timing belt (damage, wear)

9. Exhaust system (noise, leakage or otherwise defective)

10. Positive crankcase ventilation System (Hoses, connections and valve;

IGNITION

1. Ignition wiring, (damage, deterioration)

2. Spark plugs (clean and adjust the gap)
FREE INSPECTIONS

1

1

A

I

R

I

-

-

-

_
5

6

I

I

I

I

-

-

A

-
10

12

I

I

R

I

T

T

-

-
PERIODIC MAINTENANCE SERVICE AT COST

20

24

I

R

R

I

-

-

A

I

Replace every 1,00,000 km

-

-

-
I

I

-

-
-

-

-

I
I

I

I

R
30

36

I

I

R

I

T

T

-

-

-

-

-

I
40

48

I

R

R

I

-

-

A

I

I

I

I

R
SO

60

I

I

R

I

T

T

-

-

-

-

-

I
60

72

R

R

R

I

-

-

A

I

I

I

I

R
70

84

A

I

R

I

T

T

-

-

-

-

-

I
80

96

I

R

R

I

-

-

A

I

I

I

I

R

9-3
86

60G-74E
INSPECTION AND MAINTENANCE

Interval: This interval should be Judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

FUEL

1. Air cleaner Paved-road

Dusty condition

2. Accelerator cable and Throttle shafts

3. Fuel tank cap, fuel lines & connections(leakage,damage)

4. Fuel filter (leakage)

CLUTCH AND TRANSMISSION

1. Clutch pedal (play)

2. Clutch slipping (dragging or excessive damage)

3. Manual Transmission/Transfer and Differential oil (level, leakage)

DRIVE SHAFTS

1. Drive shafts boots (bent of boots damage)

BRAKE

1. Brake fluid (level, leakage)

2. Brake pedal (pedal-to-wall clearance)

3. Parking brake lever and cable (play, damage)

4. a. Brake discs and pads, (wear)

b. Brake drums & shoes

5. Master cylinder and wheel cylinder or calliper (oil leakage.boot kit)

6. Brake hoses and pipes (leakage, damage)
FREE

1

1
INSPECTIONS

5

6
10

12

Clean every 5,000 km. F
PERIODIC MAINTENANCE

20

24
30

36
40

48

Replace every 40,000 krr
50

60
SERVICE

60

72
AT

70

84
COST

80

96

Clean every 2,500 km or as required. Replace every 40,000 km. More frequent

replacement if dust condition is severe.

-

-

I

I

I

I

-

I

I

I

-

-

I

I
I&L

I

I

I

I

I

I

I

I

I

I

-

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

-

I

I

I

R

I

R

I

I

I

I

I

I
I&L

-

I

I

I

I

I

I

I

I

I

I

I

I
I&L

I

R

I

I

R

I

R

I

I

I

I

R

I

87

9-4

INSPECTION AND MAINTENANCE

60G-74E

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first
km (x 1,000)

months

WHEEL

1. Tyres (air pressure, abnormal wear, crack, ROTATION)

2. Wheels (damage)

3. Front wheel bearings (loose, damage)

4. Rear wheel bearings (loose, damage)

FRONT AND REAR SUSPENSION

1. Suspension strut (oil leakage, damage)

2. Suspension arms and knuckle supports (loose.damage)

3. Rear spring (damage)

4. Shock absorbers (oil leakage, damage)

5. All bolts and nuts (loose)

6. Suspension arms and Tension rods

STEERING

1. Steering wheel (play, loose)

2. Power steering fluid (level, leakage)/connections

3. All rods and arms (loose, damage, wear)

ELECTRICAL

1. Battery electrolyte (level, leakage)

2. Wiring harness connection (looseness, damage)

3. Lighting system (operation, stains, damage)

4. Horn (operation)

5. System voltage

BODY

1. All chassis bolts and nuts (tighten)

2. All Latches, Hinges & Locks (function)
FREE

1

1
INSPECTIONS

5

6

Rotate and

I

-

-

I

-

-

I

-

-

I

I

I

I

-

I

I

-

-

I
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

I

I&L
10

12
PERIODIC

20

24

inspect every 5,000

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
30

36

km

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
MAINTENANCE

40

48

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
50

60

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
SERVICE

60

72

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
AT

70

84

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L
COST

80

96

I

I

I

I

I

I

I

T

I

I

I

I

I

I

I

I

I

T

I&L

9-5
88

60G-74E
INSPECTION AND MAINTENANCE

Interval: This Interval should be judged

by odometer reading or months,

whichever comes first.
km (x 1,000)

months

ROAD TEST

1. Operation of Brakes, Gear shifting & speedometer

2. Body and Chassis noise

AIR CONDITIONER (if equipped)

1. Check belt tension

2. Check Receiver Drier bubbles.

3. Tighten compressor mounting bolts

4. Check all hose joints, tighten if necessary

5. Check functioning of Recirc flap .*

6. Clean condenser with low pressure water

7. Check belt for frayed edges, change if necessary

8. Check all mounting bolts
FREE

1

1

I

I

I

I

—

I

I

_

-

-
INSPECTIONS

5

6

I

I

I

I

T

I

I

C

I

I
10

12

I

I

I

I

T

I

I

C

I

I
PERIODIC

20

24

I

I

I

I

T

I

I

C

I

I
30

36

I

I

I

I

T

I

I

C

I

I
MAINTENANCE

40

48

I

I

I

I

T

I

I

C

I

I
50

60

I

I

I

I

T

I

I

C

I

I
SERVICE

60

72

I

I

I

I

T

I

I

C

I

I
AT,

70

84

I

I

I

I

T

I

I

C

I

I
COST

80

96

I

I

I

I

T

I

I

C

I

I

The rear shock absorbers are filled with

high pressure gas. Never attempt to

disassemble it or throw it into a fire.

Avoid storing it near a heater or heating

device. When scrapping the absorber,

the gas must be released from the

absorber safely. Ask your dealer for

assistance.

89

9-6

INSPECTION AND MAINTENANCE
60G-74E

All maintenance should be carried

out with the Ignition switch in the

"OFF" position and the car parked

securely on the level ground unless

otherwise specified.

If you are In any way unsure of your

ability to undertake a task, then do

not start it but contact your Maruti

dealer to perform the work for you.
ENGINE OIL AND FILTER

Specified oil

Be sure that the engine oil you use comes

under the API classification of SF, SG or SH.

Select the appropriate oil viscosity according

to the above chart.

9-7
90
70F-07-004E

60G-74E
INSPECTION AND MAINTENANCE

Hitting curbs and running over rocks

can damage tyres and affect wheel

alignment. Be sure to have tyres and

wheel alignment checked periodically

by your MARUTI dealer.

4) Check for loose wheel nuts.

5) Check that there are no nails, stones, or

other objects sticking into the tyres.

Your MARUTI is equipped with tyres

which are all the same type and size.

This is important to ensure proper

steering and handling of the vehicle.

Never mix tyres of different size or type

on the four wheels of your vehicle. The

size and type of tyres used should be

only those approved by MARUTI as

standard or optional equipment for

your vehicle.
Replacing the wheels and tyres

equipped on your vehicle with certain

combinations of aftermarket wheels

and tyres can significantly change the

steering and handling characteristics

of your vehicle. Therefore, use only

those wheel and tyre combinations

approved by MARUTI as standard or

optional equipment for your vehicle.

CAUTION

Replacing the original tyres with tyres

of a different size may result in false

speedometer or odometer readings.
60G-09-019E

Tyre Rotation

To avoid uneven wear of your tyres and to

prolong their life, rotate the tyres as illustrated.

Tyres should be rotated every 5,000 km as

recommended in the periodic maintenance

schedule. After rotation, adjust front and rear

tyre pressures to the specification listed on

your vehicle's Tyre Inflation Pressure Label.

103

9-20

INSPECTION AND MAINTENANCE

60G-74E

60G-06-009

5)
Changing Wheels

To change a wheel, use the following

procedure:

1) Remove the jack , tools and spare wheel

from the vehicle

2) Loosen, but do not remove the wheel nuts. '

3) Jack up the vehicle (follow the jacking

instructions in the EMERGENCY

SERVICE section in this manual)

4) Remove the wheel nuts and wheel.
60G-09-020E

Install the new wheel and replace the

wheel nuts with their cone shaped end

facing the wheel. Tighten each nut snugly

by hand until the wheel is securely seated

on the hub.

Lower the jack and fully tighten the nuts

[to 8.5 kg-m (61.5 Ib-ft)] in a crisscross

fashion with a wrench as shown in the

illustration.
60G-09-021

Full Wheel Cover (if equipped)

Your vehicle includes a jack crank, which has

a flat end. Use the jack crank to remove the

full wheel cap, as shown above.

9-21
104

60G-74E
INSPECTION AND MAINTENANCE

BATTERY

60G-09-022E

When installing the cover, make sure that it is

positioned so that it does not cover or foul the

air valve.
60G-09-038

Batteries produce flammable hydrogen

gas. Keep flames and sparks away from

the battery or an explosion may occur.

Never smoke when working in the

vicinity of the battery .

When checking or servicing the battery,

disconnect the negative cable. Be

careful not to cause a short circuit by

allowing metal objects to contact the

battery posts and the vehicle at the

same time.
To avoid harm to yourself or damage

to your vehicle or battery, follow the

jump starting instructions in the

EMERGENCY SERVICE section of this

manual if it is necessary to jump start

your vehicle.

The level of the battery solution must be kept

between the "UPPER" and the "LOWER" level

lines at all times. If the level is found to be

below the "LOWER" level line, add distilled

water to the "UPPER" level line. You should

periodically check the battery, battery

terminals, and battery holddown bracket for

corrosion. Remove corrosion using a stiff

brush and ammonia mixed with water, or

baking soda mixed with water. After removing

corrosion, rinse with clean water.

If your vehicle is not going to be driven for a

month or longer, disconnect the cable from

the negative terminal of the battery to help

prevent discharge.

105

9-22

INSPECTION AND MAINTENANCE

60G-74E

FUSES

60G-09-024E

©. Main fuse

®. Primary fuse (Lights)

®. Primary fuse (IG)

©. Radiator fan motor fuse

©. Primary fuse (A/C, HTR)

This vehicle has three types of fuses, as

described below:

Main Fuse - The main fuse takes current

directly from the battery.

Primary Fuses - These fuses are between the

main fuse and individual fuses, and are for

electrical load groups.

Individual Fuses - These fuses are in the fuse

box and for individual electrical circuits.
MAIN FUSE / PRIMARY FUSES

80A

60A

60A

30A

60A
All Electric Load

HEAD-R, HEAD-L, TAIL/DOME,

STOP/HORN, HAZARD

CIGAR/RADIO, I.G. COIL/

METER, WIPER/WASHER,

REAR DEF, TURN/BACK,

HEATER RELAY.

RADIATOR FAN MOTOR

A/C, HTR

Main Fuse and Primary Fuses

The main fuse and primary fuses are located

in the engine compartment. If the main fuse

blows, no electrical component will function.

If a primary fuse blows, no electrical

component in the corresponding load group

will function. When replacing the main fuse or

a primary fuse, use a genuine MARUTI

replacement.

If the main fuse or a primary fuse blows,

be sure to have your vehicle inspected

by an authorized MARUTI dealer.

Always use a genuine MARUTI

replacement. Never use a substitute

such as a wire even for a temporary

repair, or extensive electrical damage

and a fire can result.
60G-09-025E

Fuse Box

The fuse boxes are located in the engine

compartment and under the driver's side of

the dashboard.

To remove the fuse box cover under the

dashboard pull off the cover.

9-23
106

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115

60G-74E
INSPECTION AND MAINTENANCE

70F-07-060

For windshield wipers:

1. Hold the wiper arm away from the

window.
72F-09-008

2. Squeeze lock lever (A) towards wiper arms

(B) and remove the wiper frame from the

arm as shown.

113

9-30

60G-74E
EMERGENCY SERVICE

EMERGENCY SERVICE

Jacking Instructions 10-1

Jump Starting Instructions 10-2

Towing 10-4

Emergency Remedies 10-4

Warning Triangle 10-5

115