1999 SUZUKI BALENO change wheel

60G-74E

MODIFICATION WARNING

60G-00-004

The circle with a slash in this manual

means "Don't do this" or "Don't let this

happen".
Do not modify this vehicle. Modification

could adversely affect safety, handling,

performance, or durability and may

contravene regulations. In addition,

damage or performance problems

resulting from modification may not be

covered under warranty.
Improper installation of mobile

communication equipment such as

cellular talephones or CB (Citizen's

Band) radios may cause electronic

interference with your vehicle's ignition

system, resulting in vehicle

performance problems. Consult your

MARUTI dealer or qualified service

technician for advice on installing such

mobile communication equipment.

0-2
Copying, quoting or reproduction of any

part of this manual is not permitted without

explicit approval by MARUTI UDYOG

LIMITED.

60G-74E

WARRANTY POLICY

WARRANTY POLICY

Maruti Udyog Limited (hereinafter called "Maruti"), warrants that each

new Maruti vehicle distributed in India by Maruti and sold by an

authorised Maruti dealer will be free, under normal use and service,

from any defects in material and workmanship at the time of

manufacture SUBJECT TO THE FOLLOWING TERMS AND

CONDITIONS:

(1) Qualification:

To qualify for this warranty:

(a) The Maruti vehicle must be delivered by Maruti authorised

dealer and set-up, serviced by Maruti authorised dealer/

service station.

(b) The warranty registration card in respect of each vehicle

must be completed by the dealer at the time of delivery

of the vehicle and dealer should retain the same.

(2) Term:

The term of the warranty shall be twenty four (24) months

or 40,000 kilometers (whichever occurs first) from the date

of delivery to the first owner.

(3) Maruti's Warranty Obligation:

If any defect(s) should be found in a Maruti vehicle within the

term stipulated above, Maruti's only obligation is to repair or

replace at its sole discretion any part shown to be defective,

with a new part or the equivalent at no cost to the owner for

parts or labour, when Maruti acknowledges that such a defect

is attributable to faulty material or workmanship at the time of

manufacture. The owner is responsible of any repair or

replacements which are not covered by this warranty.
(4) Limitation:

This warranty shall not apply to:

(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluid

changes, headlight aiming, fastener retightening, wheel

balancing, wheelalignment and tyre rotation, cleaning of

injectors, adjustments of carburettor, ignition timing, clutch

and valve clearance.

(b) the replacement of normal wear parts including without

limitation, bulbs, battery, tyres and tubes, spark plugs, belts,

hoses, filters, wiper blades, brushes, contact points, fuses,

clutch disc, brake shoes, brake pads, cable and all rubber

parts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.

(d) any repairs or replacement required as a result of accidents

or collision.

(e) any defects caused by misuse, negligence, abnormal use or

insufficient care.

(f) any vehicle which has been modified or altered, including

without limitation, the installation of performance accessories.

(g) any vehicle on which parts or accessories not approved by

Maruti have been used.

(h) any vehicle which has not been operated in accordance with

the operating instructions in the Maruti Owner's Manual,

(i) any vehicle which has not received, during the warranty

term, the service inspections prescribed in the Maruti

Owner's Manual.

G) any vehicle which has been assembled, disassembled,

adjusted or repaired by other than an Maruti authorised

2-1

60G-74E

MODIFICATION WARNING

60G-00-004

The circle with a slash in this manual

means "Don't do this" or "Don't let this

happen".
Do not modify this vehicle. Modification

could adversely affect safety, handling,

performance, or durability and may

contravene regulations. In addition,

damage or performance problems

resulting from modification may not be

covered under warranty.
Improper installation of mobile

communication equipment such as

cellular talephones or CB (Citizen's

Band) radios may cause electronic

interference with your vehicle's ignition

system, resulting in vehicle

performance problems. Consult your

MARUTI dealer or qualified service

technician for advice on installing such

mobile communication equipment.

0-2
Copying, quoting or reproduction of any

part of this manual is not permitted without

explicit approval by MARUTI UDYOG

LIMITED.

60G-74E

WARRANTY POLICY

WARRANTY POLICY

Maruti Udyog Limited (hereinafter called "Maruti"), warrants that each

new Maruti vehicle distributed in India by Maruti and sold by an

authorised Maruti dealer will be free, under normal use and service,

from any defects in material and workmanship at the time of

manufacture SUBJECT TO THE FOLLOWING TERMS AND

CONDITIONS:

(1) Qualification:

To qualify for this warranty:

(a) The Maruti vehicle must be delivered by Maruti authorised

dealer and set-up, serviced by Maruti authorised dealer/

service station.

(b) The warranty registration card in respect of each vehicle

must be completed by the dealer at the time of delivery

of the vehicle and dealer should retain the same.

(2) Term:

The term of the warranty shall be twenty four (24) months

or 40,000 kilometers (whichever occurs first) from the date

of delivery to the first owner.

(3) Maruti's Warranty Obligation:

If any defect(s) should be found in a Maruti vehicle within the

term stipulated above, Maruti's only obligation is to repair or

replace at its sole discretion any part shown to be defective,

with a new part or the equivalent at no cost to the owner for

parts or labour, when Maruti acknowledges that such a defect

is attributable to faulty material or workmanship at the time of

manufacture. The owner is responsible of any repair or

replacements which are not covered by this warranty.
(4) Limitation:

This warranty shall not apply to:

(a) normal maintenance service required other than the three

free services, including without limitation, oil and fluid

changes, headlight aiming, fastener retightening, wheel

balancing, wheelalignment and tyre rotation, cleaning of

injectors, adjustments of carburettor, ignition timing, clutch

and valve clearance.

(b) the replacement of normal wear parts including without

limitation, bulbs, battery, tyres and tubes, spark plugs, belts,

hoses, filters, wiper blades, brushes, contact points, fuses,

clutch disc, brake shoes, brake pads, cable and all rubber

parts (except oil seal and glass run).

(c) any vehicle which has been used for competition or racing.

(d) any repairs or replacement required as a result of accidents

or collision.

(e) any defects caused by misuse, negligence, abnormal use or

insufficient care.

(f) any vehicle which has been modified or altered, including

without limitation, the installation of performance accessories.

(g) any vehicle on which parts or accessories not approved by

Maruti have been used.

(h) any vehicle which has not been operated in accordance with

the operating instructions in the Maruti Owner's Manual,

(i) any vehicle which has not received, during the warranty

term, the service inspections prescribed in the Maruti

Owner's Manual.

G) any vehicle which has been assembled, disassembled,

adjusted or repaired by other than an Maruti authorised

2-1

6OG-74E
STEERING COLUMN CONTROLS

ACC

Accessories such as the radio can operate,

but the engine is off.

ON

This is the normal operating position. All

electrical systems are on.

START

This is the position for starting the engine using

the starter motor. The key should be released

from this position as soon as the engine starts.

Never remove the ignition key while

the vehicle is moving. The steering

wheel will lock and you will not be

able to steer the vehicle.

Do not leave children alone In a

parked vehicle. Unattended children

could cause accidental movement of

the vehicle, which could result in

severe personal Injury.

Always remove the key when parked

to prevent unintentional operation of

the vehicle and to improve security.
LIGHTING/TURN SIGNAL

CONTROL LEVER

CAUTION

Do not use the starter motor for

more than 15 seconds at a time. If

the engine does not start; wait 15

seconds before trying again. If the

engine does not start after several

attempts, check the fuel and ignition

systems or consult your MARUTI

dealer.

Do not leave the ignition switch in

the "ON" position if the engine is not

running as the battery will

discharge.
60G-04-003

This control lever is located on the outboard

side of the steering column. Operate the lever

as described below.

Lighting Operation

To turn the lights on or off, twist the knob on

the end of the lever. There are three positions:

in the "OFF" position all lights are off; in the

middle position the front parking lights, tail-

lights, registration plate light, and instrument

lights are on, but the headlights are off; in the

third position the headlights come on in

addition to the other lights.

33

4-2

STEERING COLUMN CONTROLS
60G-74E

With the headlights on, push the lever forward

to switch to the high beams (main beams) or

pull the lever toward you to switch to the low

beams. When the high beams (main beams)

are on, a light on the instrument panel will

come on. To flash the high beams (main

beams) pull the lever slightly towards you and

release it.

Lights "On" Reminder (if Equipped)

A buzzer/chime sounds to remind you to turn

off the lights if they are left on when the ignition

key is removed and the driver's door is opened.
Turn Signal Operation

With the ignition switch in the "ON" position,

move the lever up or down to activate the left

or right turn signals.

Normal Turn Signal

Move the lever clockwise until it clicks to signal

a right turn or anticlockwise to signal a left

turn. When the turn is completed, the signal

will cancel and the lever will return to its normal

position.
6OG-04-006

Lane Change Signal

Some times, such as when changing lanes,

the steering wheel is not turned far enough

to cancel the turn signal. For convenience,

you can flash the turn signal by moving the

lever part way and holding it there. The

lever will return to its normal position when

you release it.

4-3
34
60G-04-006

60G-04-005

60G-04-004E

OTHER CONTROLS AND EQUIPMENTS
60G-74E

PARKING BRAKE LEVER

63B-06-001E

The parking brake lever is located between

the seats. To apply the parking brake, hold the

brake pedal down and pull the parking brake

lever all the way up.
63B-06-002E

To release the parking brake, hold the brake

pedal down, pull up slightly on the parking

brake lever, push the button on the end of the

lever with your thumb, and lower the lever to

its original position.
Never drive your vehicle with the

parking brake on: rear brake

effectiveness can be reduced from

over heating, brake life may be

shortened, or permanent brake

damage may result.

If the parking brake does not hold

the vehicle securely or does not fully

release, have your vehicle inspected

immediately by an authorized

MARUTI dealer.

Always apply the parking brake fully

before leaving your vehicle or it may

move, causing injury or damage. When

parking, make sure the gear shift lever

is left in first gear or reverse.

Remember, even though the

transmission is in gear, you must

always apply the parking brake fully.

6-1
54

60G-74E
OTHER CONTROLS AND EQUIPMENT

PEDALS

GEAR LEVER

60G-06-001

Clutch Pedal ©

The clutch pedal is used to disengage the drive

to the wheels when starting the engine,

stopping, or shifting the transmission lever.

Depressing the pedal disengages the clutch.

CAUTION

Do not drive with your foot resting on

the clutch pedal. It could result in

excessive clutch wear, clutch damage,

or unexpected loss of engine braking.
Brake Pedal ®

Your MARUTI vehicle is equipped with front

disc brakes and rear drum brakes. Depressing

the brake pedal applies both sets of brakes.

You may hear occasional brake squeal when

you apply the brakes. This is a normal

condition caused by environmental factors

such as cold, wet, snow, etc.

If brake squeal is excessive and occurs

each time the brakes are applied, you

should have the brakes checked by

your MARUTI dealer.

A WARNING

Do not "ride" the brakes by applying

them continuously or resting your foot

on the pedal. This will result in

overheating of the brakes which could

cause unpredictable braking action,

longer stopping distances, or

permanent brake damage.

Accelerator Pedal ®

This pedal controls the speed of the engine.

Depressing the accelerator pedal increases

power output and speed.
70F-04-005E

The gear change pattern is shown in the

illustration. For details on how to use the

transmission, refer to USING THE

TRANSMISSION in the OPERATING YOUR

VEHICLE section.

55

6-2

OTHER CONTROLS AND EQUIPMENTS

60G-74E

CUP HOLDER (if equipped)
TYRE CHANGING TOOLS

60G-06-007

3)
Continue to lift up the bonnet until it is high

enough to support with the prop rod.

Make sure the bonnet Is fully closed

and latched before driving. If it is not,

it can fly up unexpectedly during

driving, obstructing your view and

resulting in an accident.
60G-06-008

To use the cup holder, pull it out fully. After

using the holder, push it back in.

Do not use the cup holder to hold cups

containing hot liquids, or objects other

than cups. Objects in the cup holder

may be thrown about during a sudden

stop or impact, and could cause

personal injury.
60G-06-009

The jack, wheel wrench and jack crank are

stowed in the luggage compartment behind

the rear seat.

To remove the jack, turn its shaft

counterclockwise and pull the jack out of the

storage bracket. To stow the jack, place it in

the storage bracket and turn the shaft

clockwise until the jack is securely held in

place.

6-7
60

60G-74E
OTHER CONTROLS AND EQUIPMENT

LUGGAGE COMPARTMENT TRIM TRUNK (BOOT) LIGHT (if equipped)

Luggage or other cargo placed in the luggage

compartment are hidden from view by a

luggage compartment trim.

Do not carry items on top of the

luggage compartment trim, even if they

are small and light. Objects on top of

the trim could be thrown about In an

accident, causing injury, or could

obstruct the driver's rear view.

60G-06-010
6OG-O6-O11

The jack should be used only to change

wheels. It is important to read the

jacking Instructions in the

EMERGENCY SERVICE section of this

manual before attempting to use the

jack.
When you open the trunk (boot) lid, the trunk

(boot) light comes on and remains on as

long as you keep the lid open.

Do not leave the boot (trunk) lid open

for a long time, or the battery will

discharge.

After using the jack, jack crank and

wheel wrench, be sure to stow them

securely or they can cause injury if an

accident occurs.

61

6-8

OTHER CONTROLS AND EQUIPMENTS
60G-74E

FRONT SEAT BACK POCKET

(if equipped)
REAR SPOILER WITH STOP LAMP

Other Controls (if equipped)

63B-06-022

This pocket is provided for holding light and

soft things such as gloves, newspapers or

magazines.

Do not put hard or breakable objects

In the pocket. If an accident occurs,

objects such as bottles, cans etc. can

injure the occupants in the rear seat.
60G-50-002E

Rear Spoiler is provided to improve

aerodynamic stability at higher speeds and

better asthetics. Stop Lamp (if equipped) is

fitted inside the Rear Spoiler. The stop lamp

will glow as and when the Brake Pedal is

depressed.

CAUTION

Never close the dicky door too hard or

with jerk or lift the dicky by holding

spoiler, rear spoiler may get damaged.

Close the dicky door gently and make

sure it is closed properly.
ALLOY WHEELS

Maintenance with tyre wears (if equipped)

60G-50-003E

Wider alloy wheels are provided in the vehicle

for better grip on the road and more fuel

economy. For balancing of wheels please

consult MARUTI authorised workshop.

CAUTION

Never try to remove the tyre from alloy

wheel rim in convention manner (by

hammering), it will damage the wheel

rim. Always insist on tyre changing

machine.

6-9
62

60G-74E

OTHER CONTROLS AND EQUIPMENT

POWER ANTENNA Other Controls

(if equipped)
LEATHER COVER

Steering Column Controls (if equipped)

60G-50-004E

60G-50-006E

Power antenna on the rear side will

automatically come up on switching on the

AM/FM receiver fitted in the vehicle.
For better control on steering wheel leather

cover is provided.
HIGH MOUNT STOP LAMP

(if equipped)

High mount stop lamp is provided with your

vehicle and is fitted on rear parcel tray. The

stop lamp will glow as when the brake pedal

will be depressed.

To change the bulb of the stop lamp, remove

the clips at both sides of the cover, by

pressing the inner pin inside so that the clip

gets loose and remove the bulb on turning

it anticlock-wise

The rating of bulb is 21W/12V.There are one

bulb in high mount stop lamp.

63

6-10

60G-74E
OPERATING YOUR VEHICLE

Reduce your speed and change

down to a lower gear before going

down a long or steep hill. A lower

gear will allow the engine to provide

braking. Avoid riding the brakes or

they may overheat, resulting in brake

failure.

When driving on slippery roads, be

sure to slow down before changing

down. Excessive and or sudden

changes in engine speed may cause

loss of traction, which could cause

you to lose control.

Make sure that the vehicle is

completely stationary before you

change into reverse.
CAUTION

To help avoid clutch damage, do not

use the clutch pedal as a footrest

while driving or use the clutch to

keep the vehicle stationary on a hill.

Depress the clutch fully when

changing gear.

When changing gears or starting off,

do not race the engine. Racing the

engine can shorten engine life and

prevent smooth operation.
BRAKING

The distance needed to bring any vehicle to a

halt increases with the speed of the vehicle.

The braking distance needed, for example, at

60 km/h will be approximately 4 times greater

than the braking distance needed at 20 km/h.

Start to brake the vehicle when there is plenty

of distance between your vehicle and the

stopping point, and slow down gradually.

69

7-4

OPERATING YOUR VECHILE

60G-74E

RUNNING-IN

Servo assisted brakes

Your vehicle has servo assisted brakes which

works with the assistance of engine vacuum.

Do not switch off the engine while

vehicle is in motion, for example, while

driving down a hill as this will cause

loss of vacuum assistance leading to

reduction of braking efficiency

substantially.

If servo assistance is lost due to a stalled

engine or other failures, the system is still fully

operational on reserve power and you can

bring the vehicle to a complete stop by

pressing the brake pedal once and holding it

down. The reserve power is partly used up

each time you depress the brake pedal. Apply

smooth and constant pressure to the pedal.

Do not pump the pedal.
Even without reserve power in the

brake system, you can still stop the

vehicle by pressing the brake pedal

harder than normally required.

However, the stopping distance may be

lonaer.

On loose surface where the wheels can

easily loose traction (such as gravel,

etc.), the stopping distance required for

your vehicle may be greater than for a

comparable vehicle with a conventional

brake system. Allow for extra stopping

distance when driving on loose

surfaces.
CAUTION

The future performance and reliability

of the engine depends on the care and

restraint exercised during its early life.

It is especially important to observe the

following precautions during the initial

1000 km of vehicle operation.

• After starting, do not race the

engine. Warm it up gradually.

• Avoid prolonged vehicle operation at

a constant speed. Moving parts will

bed in better if you vary your speed.

• Do not exceed 100 km/h.

• Start off from a stop slowly. Avoid

full throttle starts.

• If possible, avoid hard braking,

especially during the first 300 km of

driving.

• Do not drive slowly with the

transmission in a high gear.

• Drive the vehicle at moderate engine

speeds.

7-5
70
If water gets into the brake drums,

brake performance may become poor

and unpredictable. After driving

through water or washing the

underside of the vehicle, test the brakes

while driving at a slow speed to see if

they have maintained their normal

effectiveness. If the brakes are less

effective than normal, dry them by

repeatedly applying the brakes while

driving slowly until the brakes have

regained their normal effectiveness.

60G-74E
DRIVING TIPS AND SAFE DRIVING

Snow Chains

If you must use snow chains to increase tyre

traction, observe the following precautions:

• Choose a safe place away from traffic to

install the chains.

• When installing the chains carefully follow

the manufacturer's instructions.

• Install the chains on the front tyres.

• With the chains on, drive only at slow and

moderate speeds.

• If Your Vehicle Gets Stuck

If your vehicle gets stuck in snow, mud, or

sand, follow the directions below:

1) Change back and forth between first gear

and reverse. This will create a rocking

motion which may give you enough

momentum to free the vehicle. Press

gently on the accelerator to keep wheel

spin to a minimum. Remove your foot from

the accelerator while changing gear.

Do not race the engine. Excessive wheel

spin will cause the tyres to dig deeper,

making it more difficult to free the vehicle.

2) If your vehicle remains stuck after a few

minutes of rocking, get another vehicle to

pull you out.
Do not allow anyone to stand near the

vehicle when you are rocking it, and do

not spin the wheels faster than an

indicated 40 km/h on the speedometer.

Personal injury and/or vehicle damage

may result from spinning the wheels

too fast.

CAUTION

Do not continue rocking the vehicle for

more than a few minutes. Prolonged

rocking can cause engine overheating

or transmission damage.

DRIVING ON WET ROADS

CAUTION

When driving on wet roads, avoid driv-

ing through large amount of standing

water on the road. Large amount of

water entering the engine compart-

ment may cause damage to the engine

and or electrical components.

If stuck in deep water, do not start till

water level drops.

Water Is incompressible substance,

water inside engine is harmful to

the engine."
Make sure your tyres are in good

condition and always maintain the

specified tyre pressure. Refer to

"TYRES" in the "INSPECTION AND

MAINTENANCE" section for details.

Do not use tyres other than those

specified by MARUTI. never use

different sizes or types of tyres on

the front and rear wheels. For

information regarding the specified

tyres, refer to ^"SPECIFICATIONS"

section.

Never use oversized tyres or special

shock absorbers and springs to

raise (jack up) your vehicle.This will

change the handling characteristics.

After driving through water, test the

brakes while driving at a slow speed

to see if they have maintained their

normal effectiveness. If the brakes

are less effective than normal, dry

them by repeatedly applying the

brakes while driving slowly until the

brakes have regained their normal

effectiveness.

75

8-2

DRIVING TIPS AND SAFE DRIVING

60G-74E

DO'S AND DON'TS FOR SAFE

DRIVING

Exercise care in handling your vehicle. Be

conscious of not only your own safety but also

the safety of others on the road, and thus enjoy

the best and most comfortable driving

experience.

This section contains basic rules for safe

driving. Read it carefully for good

understanding of the content so that you can

enjoy safe and pleasant driving in your Maruti

vehicle.

72F-08-001

Starting

1. Adjust the driver's seat for the proper

driving posture.

2. Adjust the rear view mirror so as to obtain

the best possible rear view.

3. Before moving off, look forward and back

to confirm safety.
72F-08-002

72F-08-003

8-3
76