1999 OLDSMOBILE AURORA instrument panel

yellowblue
2-21
RUN (D): This is the position the switch returns to after
you start your engine and release the switch. This is the
position for driving. Even when the engine is not
running, you can use RUN to operate your electrical
power accessories and to display some instrument panel
warning lights.
START (E): This position starts your engine. When the
engine starts, release the key. The ignition switch will
return to RUN for normal driving.
NOTICE:
If your key seems stuck in LOCK and you can't
turn it, be sure you are using the correct key; if
so, is it all the way in? If it is, then turn the
steering wheel left and right while you turn the
key hard. But turn the key only with your hand.
Using a tool to force it could break the key or the
ignition switch. If none of this works, then your
vehicle needs service.
Key Reminder Warning
If you leave your key in the ignition, with the engine off,
you will hear a warning chime when you open the
driver's door.
Retained Accessory Power
After you turn the ignition off and remove the key, you
will still have electrical power to such accessories as the
radio, power windows, and sunroof (option) for up to 10
minutes. But if you open a door, power is shut off.
Always leave your key in LOCK. If you leave your key
in any other position than LOCK, your battery will
discharge prematurely.
Starting Your Engine
Move your shift lever to PARK (P) or NEUTRAL (N).
Your engine won't start in any other position
-- that's a
safety feature. To restart when you're already moving,
use NEUTRAL (N) only.
ProCarManuals.com

yellowblue
2-35 Turn and Lane Change Signals
The turn signal has two upward (for right) and two
downward (for left) positions. These positions allow you
to signal a turn or a lane change.
To signal a turn, move the lever all the way up or
down. When the turn is finished, the lever will
return automatically.
An arrow on the
instrument panel will
flash in the direction of
the turn or lane change.
To signal a lane change, just raise or lower the lever
until the arrow starts to flash. Hold it there until you
complete your lane change. The lever will return by
itself when you release it.As you signal a turn or a lane change, if the arrows don't
flash but just stay on, a signal bulb may be burned out
and other drivers won't see your turn signal.
If a bulb is burned out, replace it to help avoid
an accident.
If the arrows don't go on at all when you signal a turn,
check the fuse (see ªFuses and Circuit Breakersº in the
Index) and for burned-out bulbs.
Turn Signal On Chime
If your turn signal is left on for more than 3/4 of a
mile (1.2 km), a chime will sound and the DIC will
display the TURN SIGNAL ON? reminder message.
To turn off the chime, move the turn signal lever to the
off position. To turn off the DIC message, press any
button on the DIC.
ProCarManuals.com

yellowblue
2-36 Headlamps
Turn the band to this symbol to turn on:

Parking Lamps

Sidemarker Lamps

Taillamps

Instrument Panel Lights

License Plate Lamps
Turn the band to this symbol to turn on the
headlamps as well as the other operating lamps.
Turn the band to OFF to turn off the lamps/lights.
Headlamp High/Low Beam Changer
To change the headlamps
from low beam to high or
high to low, pull the turn
signal lever all the way
toward you until you hear a
click. Then release it.
When the high beams are
on, a light on the instrument
panel also will be on.
ProCarManuals.com

yellowblue
2-40
1. Move the cruise control switch to ON.
2. Get up to the speed you want.3. Push in the button at the end of the lever and release
it. The CRUISE light on the instrument panel will
come on.
4. Take your foot off the accelerator pedal.
ProCarManuals.com

yellowblue
2-42
Ending Cruise Control
There are two ways to turn off the cruise control:

Step lightly on the brake pedal, or

Move the cruise switch to OFF. The CRUISE light
will also go out.
Erasing Speed Memory
When you turn off the cruise control or the ignition,
your cruise control set speed memory is erased.
Exterior Lamps
Headlamps
See ªTurn Signal/Multifunction Leverº in the Index.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DRL can be helpful in many different driving
conditions, but they can be especially helpful in the
short periods after dawn and before sunset.
A light sensor on top of the instrument panel makes the
DRL work, so be sure it isn't covered.The DRL system will make your low
-beam headlamps
come on at reduced brightness in daylight when:

the ignition is on,

the headlamp switch is off and

the transaxle is not in PARK (P).
When DRL are on, only your low
-beam headlamps will
be on. The parking lamps, taillamps, sidemarker and
other lamps won't be on. Your instrument panel won't
be lit up either.
When it's dark enough outside, your low
-beam headlamps
will change to full brightness. The other lamps that come
on with your headlamps will also come on. When it's
bright enough outside, the regular lamps will go off, and
your low
-beam headlamps change to the reduced
brightness of DRL.
To idle your vehicle with the DRL off, shift the
transaxle into PARK (P). The DRL will stay off until
you shift out of PARK (P).
To turn off all exterior lighting at night when you are in
PARK (P), turn off the headlamps and move the twilight
sentinel control, located to the left of the steering
column, all the way toward MIN. See ªTwilight
Sentinelº in the Index.
As with any vehicle, you should turn on the regular
headlamp system when you need it.
ProCarManuals.com

yellowblue
2-43 Fog Lamps
To turn on the fog lamps,
first turn on the parking
lamps or headlamps. Then
press the fog lamp switch
located on the left side of
the instrument panel. A
light will glow on the
switch when the fog lamps
are on. To turn off the fog
lamps, press it again.
The fog lamps will also turn off when you turn on your
high
-beam headlamps, but will turn on again when you
switch to low beams.
Cornering Lamps
The cornering lamps are designed to come on when you
signal a turn. This will provide more light for cornering
at night.
ProCarManuals.com

yellowblue
2-44 Twilight Sentinel


Twilight sentinel turns the
headlamps, taillamps and
parking lamps on and off
by sensing how dark it
is outside.
To operate it, leave the headlamp switch off and move
the twilight sentinel control toward MAX. The control is
located to the left of the steering column.
If you move the control all the way to MAX, your lamps will
remain on for three minutes after you turn off your engine. If
you move the control toward MIN, the lamps will go off
quickly when you turn off your engine. You can set this delay
time for only a few seconds or up to three minutes.
Light Sensor
Your twilight sentinel and daytime running lamps work
with the light sensor on top of the instrument panel.
Don't cover it up. If you do it will read ªdarkº and the
headlamps will come on.
Interior Lamps
Instrument Panel Brightness Control
You can brighten or dim your instrument cluster, radio and
climate control displays and control lights by rotating the
INTERIOR LIGHTS control between LO and HI when
your lights are on. Rotate the control all the way to HI and
you will turn on the interior courtesy lamps.
Courtesy Lamps
When any door is opened, several lamps go on. They
make it easy for you to enter and leave the car. To turn
on these lamps, rotate the INTERIOR LIGHTS knob all
the way to HI.
ProCarManuals.com

yellowblue
2-45 Illuminated Entry
Press the UNLOCK button on the remote lock control
transmitter and the interior courtesy lamps will come on
and stay on for up to one minute. The lamps will turn off
immediately by pressing the LOCK button on the
remote lock control transmitter, starting the ignition or
activating the power door locks.
Delayed Illumination
When you open the door to enter your vehicle, the
interior lamps will come on. When you close the door
with the ignition off, the interior lamps will stay on for
25 seconds or until the ignition is turned on. Note that
locking the doors with the power door lock switch will
override the delayed illumination feature and the lights
will turn off right away.
Theater Dimming
This feature allows for a three to five-second fade out of
the courtesy lamps instead of immediate turn off. They
will not fade if the interior lights switch is used.
Exit Lighting
With this feature, the interior lamps will come on for
25 seconds after you remove the key from the ignition.
This will give you time to find the door pull handle or
lock switches when you exit the vehicle.
Parade Dimming
This feature prohibits the dimming of your instrument
displays during daylight while your headlamps are on.
This feature operates with the light sensor for the
twilight sentinel and is fully automatic. When the light
sensor reads darkness outside, you will be able to dim
your instrument panel displays once again.
Perimeter Lighting
When the UNLOCK button on the remote lock control
transmitter is pressed, the headlamps, parking lamps,
back
-up lamps and cornering lamps will come on if it is
dark enough outside according to the twilight sentinel.
This feature can be programmed on or off for each
driver's transmitter.
To turn the feature off:
1. Turn the ignition key to OFF.
2. Press and hold the door lock switch throughout this
procedure. All doors will lock.
ProCarManuals.com